Argos Romantic Large 653/9441 User manual

Romantic Large TV Unit
Assembly Instructions - Please keep for future reference 653/9441
Dimensions
Width - 120cm
Depth - 38cm
Height - 52.6cm
Issue 1 - Nov/20/16
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800

1
Safety and Care Advice
Important –Please read these instructions fully before starting assembly
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Check you have all the
components and tools listed on
the following pages.
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
• Parts of the assembly will be
easier with 2 people.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
tightend properly.
Handy Hints

Components - Panels
Please check you have all the panels listed below
2
Top front rail (108 x 3.8cm)
4
Left frame side (50.1 x 36.4cm)
2
Top panel (120 x 38cm)
1
Shelf panel (108 x 32.8cm)
5
If you have damaged or missing components, call the
Customer Helpline:
Argos = 0345 6400800
Back panel (109.2 x 34.4cm)
9
Back rail (108 x 8.8cm)
7
Bottom front rail (108 x 7.5cm)
6
Back drawer panel x 2 (48.4 x 16.5cm)
10
Right frame side (50.1 x 36.4cm)
3
Center panel (35.1 x 32cm)
8
Left side drawer panel x 2 (30 x 16.5cm)
11 Right side drawer panel x 2 (30 x 16.5cm)
12
Left drawer front (53.7 x 21.3cm)
13
Bottom drawer panel x 2 (49.6 x 28.8cm)
15
Right drawer front (53.7 x 21.3cm)
14

3
A
E
30mm Bolts x 3
B
25mm Screw x 16 Allen key x 1
C
Note:
may be supplied than are required.
16mm Flat washer x 3
D
Components - Fittings
10mm Spring washer x 3
F
GHI
15mm Cam locks x 17 25mm Bolts x 2 30mm Metal handle x 2
35mm Cam bolts x 17
Tools required
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Ruler/tape
measure
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
The screws length is measured from the head tothe point (30mm screw shown).
20mm Pads x 4
K
25mm Rectangle Pad
L

4
Assembly Instructions
Step 1
Insert Cam bolts
a: Insert Cam bolts
into top panel
as shown
.
a:
b:
1
F
F
F
1
b: Insert Cam bolts
into left frame side
and right frame
side as shown
F
F
F
F
2
2
3
3
FF
F

5
Assembly Instructions
Insert Cam bolts
c: Insert Cam bolts
into shelf panel
as shown
.
c:
d:
5
5
d: Insert Cam bolts
into back rail
and bottom front
rail as shown
F
7
6
F
F
F
F
7
6

6
Assembly Instructions
Assembly frame side
Step 2
Insert Cam locks
into the shelf panel
back rail and top
front rail . Press
firmly together . Turn the
cam lock clockwise with
a philipshead screwdriver
to lock.
3
G
Step 3
Assembly center panel
4
7
5
7
5
4
G
Insert Cam locks
into the bottom front rail
and center panel
Press firmly together.
Turn the cam locks
clockwise with a
philipshead screwdriver
to lock.
6
8
5
G
G
3
G
6
8
G
T
N
O
R
F
FRONT
FRONT

7
Assembly Instructions
a: Assembly frame side
Step 4
Insert Cam locks
into the shelf panel
back rail ,bottom
front rail and top
front rail . Press
firmly together . Turn the
cam lock clockwise with
a philipshead screwdriver
to lock.
Step 5
Assembly back panel
7
5
G
G
G
2
6
4
9
6
7
4
5
Insert back panel
into the slot of back rail
& frame side .
9
Remove
K
a: b:
b: Attach the pad
Remove cover paper on the
pad . Attach the pad
into under the legs.
Remove cover paper on the
pad . Attach the pad
into under the center panel.
With help stand the
assembled unit upright.
K
L
K
L
K

8
Assembly Instructions
Assembly Drawer
Step 7
a:
a:
Position Left side
drawer panel ,and
right side drawer panel
into left drawer front
Fix through holes
using screw
13
13
11
12
11
12
A
A
A
b:
Insert bottom panel
drawer into the slot of
side drawer panel &
drawer front panel.
b: 15
15
Step 6
Assembly top panel
G
G
E
D
B
C
1
Insert Cam locks
into side panel
as shown .Press top panel
onto assembly.Turn cam
locks to lock . Insert bolts
, Spring washer ,
flat washer , Tighten
with supplied allen key
Do not over tighten.
G
23
C
BD
E
1

9
Assembly Instructions
Assembly Drawer
Step 8
Position two drawers
into the assembled unit.
c:
c:Position back panel
drawer
Fix thourgh holes
using screw
10
AA
A
d: Position metal handle
into drawer front
panel.
Fix through holes
using bolt
d:
I
H
H
I
Repeat (step 7) for
second drawer with
right drawer front .
10
14
Left Drawer Right Drawer