Argos 6001955 User manual

Turner Black PU Seated Barstool
Assembly Instructions - Please keep for future reference
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the customer helpline: 08456 400800
6001955
Dimensions
Width - 42cm
Depth - 55cm
Height - 97～119cm
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Care and maintenance
• To clean, wipe clean with a
soft dry cloth.
• From time to time check that
there are no loose screws on
this unit.
• Assemble this product on a
flat surface.
• Assemble all parts loosely
before tightening any bolts.
• Discard all extra fittings and
keep fittings out of reach of
children.
• We suggest you spend a short
time reading through this leaflet
and follow the simple step by
step assembly instructions.
• Do not discard any of the
packaging until you have
checked that you have all the
parts and the pack of fittings.
• Maximum safe weight of user:
100kgs.
• Retain Assembly Instructions
for future reference.

1
Components - Parts
Please check you have all the parts listed below
Please check you have all the fittings listed below
Components - Fittings If you have damaged or missing components,
call the customer helpline: 08456 400800
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
1
4
2
5
3
6
Seat Upper leg Gaslift
Foot rest Decor ring Base
AB C
Bolt x 4 Washer x 4 Allen key x 1
Ruler - Use this ruler to help correctly identify the screws
105150 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170

Assembly Instructions
Step 1
Step 2
Attaching upper leg
Attaching footrest
Connect the footrest
into the upper leg by
turning it clockwise.
Place the seat upside
down on a flat protected
surface. Position the
upper leg and make
sure that the arrow on
the plate is pointing
towards the front edge of
the seat as shown in the
inset diagram. Secure
using washer and
bolt .
2
A
A
B
B
A
B
A
A
B
B
Arrow
4
2
2
2
2
2
1
1
1
4

If you need help or have damaged or missing parts, call the customer helpline: 08456 400800
Lever
Assembly Instructions
Step 3
Step 4
Attaching gaslift
Attaching the seat
Position the seat as
shown and insert the
gaslift into the upper
leg . Secure by press-
ing down the seat firmly.
Gaslift operation
To adjust the seat higher,
lift up the lever under the
seat and release at
desired height.
To lower the seat, lift up
the lever while seated on
the stool.
Plastic tip
3
Place the base on a
flat protected surface.
Position the decor ring
on the base and
insert the gaslift into
the decor ring and hole
of the base.
Important:
Remove plastic
tip cover on gaslift
before assem-
bling.
6
6
5
5
3
3
3
2
2
3

Width - 41cm
Depth - 52cm
Height - 97-119cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 15/08/13
Dimensions
Turner Bar Stool
Assembly Instructions - Please keep for future reference 600/1955

1
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warnings
Care and maintenance
• Do not discard any of the
packaging until you have
checked that you have all the
parts and the pack of fittings.
• Discard all extra fittings and
keep fittings out of reach of
children.
• At least 2 people are required
to assemble this product.
• Assemble this product on a flat
surface.
• Assemble all parts loosely
before tightening any bolts.
• Unit weight: 9kgs.
• Maximum safe weight of user:
110kgs.
• Retain Assembly Instructions
for future reference.
• Dispose of all packaging
carefully and responsibly.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Do not stand on the stool.
• Do not use the stool as a step
ladder.
• Make sure the legs remain in
contact with the ground.
• Do not knock the surface of
the seat against sharp solid
surfaces.
• This product should only be
used on firm, level ground.
• Do not sit with sharp objects in
back pockets as this may
damage the seat surface.
• Please clean the product using
either damp (not wet) cloth and
a mild domestic soap solution or
by using an appropriate polish.
• Do not use any abrasive
materials when cleaning.
• From time to time check that
there are no loose bolts on this
unit.

2
Components - Parts
Please check you have all the parts listed below
Please check you have all the fittings listed below
Components - Fittings
If you have damaged or missing components,
call the Customer Helpline: 08456 400800
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
105 150 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
1Seat
(41.5 x 41 x 52cm)
2Upper leg
(Ø16 x 39.5cm)
3Gaslift
(Ø5 x 50.5~72.5cm)
4Foot rest
(Ø1.6 x 38 x 3.3cm)
5Decor ring
(Ø5 x 7.5 x 2.2cm)
6Base
(Ø41 x 8.5cm)
A
M6 x 25mm Bolt x 2
C
Washer x 4
D
Allen key x 1
B
M6 x 18mm Bolt x 2

3
Assembly Instructions
Step 1
Step 2
Attaching upper leg
Attaching footrest
Connect the footrest
into the upper leg by
turning it clockwise.
Place the seat upside
down on a flat protected
surface.
Position the upper leg
and make sure that the
arrow on the plate is
pointing towards the front
edge of the seat as
shown in the inset
diagram.
Secure using washers
and bolts for the two
holes near the front of
the seat & bolts for the
back holes.
A
C
A
A
B
B
C
C
A
C
C
B
C
B
C
Arrow
4
22
2
2
2
2
1
1
1
1
4

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Lever
Assembly Instructions
Step 3
Step 4
Attaching gaslift
Attaching the seat
Position the seat as
shown and insert the
gaslift into the upper
leg . Secure by
pressing down the seat
firmly.
Gaslift operation
Assembly is complete.
To adjust the seat higher,
lift up the lever under the
seat and release at
desired height.
To lower the seat, lift up
the lever while seated on
the stool.
Plastic tip
4
Place the base on a
flat protected surface.
Position the decor ring
on the base and insert
the gaslift into the
decor ring and hole of
the base.
Important:
Remove plastic tip
cover on gaslift
before
assembling.
6
6
5
5
3
3
3
2
2
3