Argos Haversham User manual

Haversham - 3 Dr 3 Drw Sideboard
159/9280
Assembly Instructions
- Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400 800
Important – Please read these instructions fully before starting assembly
Dimensions
Width - 120cm
Depth - 39cm
Height - 80,5cm
Issue 1 - 01/10/10

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: if required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
. Check you have all the
components and tools listed on
pages 2 and 3.
. Remove all fittings from the
plastic bags and separate them
into their groups.
. Keep children and animals
away from the work area, small
parts could choke if swallowed.
. Make sure you have enough
space to layout the parts before
starting.
. Do not stand or put weight on
the product, this could cause
damage.
. Assemble the item as close
to its final position (in the same
room) as possible.
. Assemble on a soft level
surface to avoid damaging the
unit or your floor.
. We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
. Parts of the assembly will be
easier with 2 people.
. Dispose of all packaging
carefully and responsibly.
This product contain
Natural timber; you may
notice some variation in the grain
and colour of different component
parts which is normal for furniture
produced using natural wood and
is not the result of any
manufacturing fault.
.
Care and maintenance
.
. Avoid placing the furniture in
direct sunlight as this will cause
the timber to prematurely age.
Use an appropriate furniture
polish for natural wood
furniture and a dry cloth to
clean the product.
. From time to time check
that there are no loose
screws on this unit.
. This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.

Components - Panels
Please check you have all the panels listed below
2
01
02
03
04
06
08
16
05
07
09 10
13
14
22
23
19 20 21
15
11
Right front leg (78,5 x 4,5cm)
Right back leg (78,5 x 4,5cm)
Left front leg (78,5 x 4,5cm)
Left back leg (78,5 x 4,5cm)
Door X 3 (54,9 x 36,2cm)
Large middle wall (72 x 36cm)
Central foot (5 x 4cm)
Top panel (120 x 39cm)
Base panel (110 x 39cm)
Shelf (x 36cm)72,5 Back panel (x 37,7cm)74,4
Drawer front X 3
Drawer bottom X 3
Large runner X 2
Runner X 4
Drawer left side X 3 Drawer right side X 3 Drawer back X 3
Small middle wall
(x 18cm)36,2
(
(
(
x 30,7cm)34,8
35 x 2,8cm)
35 x 1,9cm)
(((
((
35 x 13cm) 35 x 13cm) 29,6 x 13cm)
(x 19,5cm)36
Back panel X 2 (x 36,8cm)74,4
12 H profile 73 (x 2,2cm)
17 18
Left side panel (73,5 x 29cm)Right side panel (73,5 x 29cm)

3
2m
Components - Fittings
Please check you have all the fittings listed below
If you have damaged or missing components,
call the Customer Helpline: 08456 400 800
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
0510 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Tools required
Phillips screwdriver
(medium & large)
Eye protection
(when using a
hammer or glue)
Small
hammer
Ruler/tape
measure
AA
A
D
H
Foot pad 5 X
AB
8,0 x 30mm Wooden dowel X 54
C
I
3,5 x 30mm Screw X 48
3,5 x 25mm Screw X 12
3,5 x 40mm Screw X 3
3,5 x 14mm Screw X 25
EF
Handle X 6 Plastic pin X 6
G
10 x 10 Nail X 35
JL
Locking nut X 16
M
Hinge plate X 4 Thin hinge plate X 2
N
Hinge X 6
O
Metal dowel X 16
P
Wall strap X 1
QR
Washer X 2 Squared washer X 4

.a)
.b)
A
J
L
D
D
Assembly InstructionsAssembly InstructionsAssembly Instructions
Step 2
Step 1
Assembly Instructions
A
A
A
O
O
02
01
03
04
4
Insert wooden dowels
into leg , , and
as shown.
Screw metal dowels
into leg , , and
.
Do note over
tighten metal
dowels.
a) Fit side panel , left
front leg and left back
leg together.
b) Insert locking nuts
where shown. Use a
screwdriver to turn locking
nuts clockwise to lock.
Fix hinge plates using
screws as shown.
01
01
17
01
02
02
04
22
17
02
03
03
03
03
04
22
04
A
A
O
D
B
L
J
04
A
A
A
A
A
A
A
A
A
A
A
O
O
O
O
O
O
O
O
O
O
O
O
01
02
03
04
J
J
J
J
J
J
04
03
17
B
B
A
A
A
A
22
22
22
22
Make sure holes
face this side
Parts , , and
are labelled for easier
identification.
Insert wooden dowels
into large runners .
Fix runner to side panel
using screws . Make
sure holes in runner are
positioned as shown.

Assembly Instructions
Step 3
Step 4
5
A
A
A
A
A
A
a) Fit side panel , right
front leg and right back
leg together.
b) Insert locking nuts
where shown. Use a
screwdriver to turn locking
nuts clockwise to lock.
Fix hinge plates using
Fix thin hinge plates
screws as shown.
.using screws as shown.
18
02
01
D
D
L
M
J
A
.
D
D
L
J
A
J
J
J
J
J
J
D
D
.b)
.a)
02
18
01
A
A
A
A
A
D
D
M
M
A
A
A
A
A
A
A
A
A
A
A
A
A
M
D
D
08
09
07
15
D
A
15
Front view
==
B
B
22
22
22
18 B
Fix runner to side panel
using screws . Make
sure holes in runner are
positioned as shown. Make sure holes
face this side
Insert wooden dowels
into the indicated parts.

Assembly Instructions
Step 5
Step 6
Step 7
6
I
C
C
C
C
C
C
I
07
09
08
18
01
02
C
Fix large middle wall
to base panel using
screws .
Fix shelf using screws
.
Fix assembled right side
panel using screws
as shown.
08
07
I
C
09
18 C

Assembly Instructions
Step 8
Step 9
7
C
C
C
C
C
C
C
C
C
C
C
O
O
O
O
O
03
17
04
05 15
15
PAINTED EDGE
Fix assembled left side
panel using screws
as shown.
Fix small middle wall to
the top panel using
screws . Screw metal
dowels where shown.
17
05
C
O
C
ATTENTION!
Make sure
panels are
positioned as show
in the picture.
15

Assembly Instructions
Step 10
Step 11
8
05
05
16
I
23
23
23
C
C
B
B
B
B
C
J
J
J
J
J
B
H
5x
H
H
H
H
H
With the help of a hammer,
fix foot pads as shown.
H
Fix top panel to the
assembled part using
screws . Insert locking
nuts as shown. Use a
screwdriver to turn locking
nuts clockwise to lock.
Fix central foot using
screw .
Fix runners using
screws . Make sure
holes in runners are
positioned as shown.
05
C
J
16
I
23
B
Make sure holes
face this side

Assembly Instructions
Step 12
Step 13
9
23
23
23
B
B
B
B
B
X
12
11
11
10
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
R
G
R
G
R
G
R
R
G
G
IMPORTANT
Cabinet must be
“square” when
back is attached.
Fix runners using
screws . Make sure
holes in runners are
positioned as shown.
Position back panels
and within rebates with
profile in place as
shown. Attach back panels
using nails and where
shown, use squared
washers plus nails .
Note that back panel is
larger than the back
panels and must be
positioned on the left side.
23
B
Make sure holes
face this side
G
G
R
10
11
12
10
11