Argos 239/2352 User manual

ADDINGTON STYLES TWO TONE
CONSOLE TABLE
Dimensions
Width - 70cm
Depth - 30cm
Height - 75cm
Issue 1 - 26/02/14
Important – Please read these instructions fully before starting assembly
Assembly Instructions - Please keep for future reference 239/2352

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
•Check you have all the
components and tools listed on
the following pages
plastic bags and separate them
into their groups.
•Keep children and animals
away from the work area, small
parts could choke if swallowed.
•Make sure you have enough
space to layout the parts before
starting.
•During assembly do not stand
or put weight on the product,
this could cause damage.
•Assemble the item as close
to its final position (in the same
room) as possible.
•Assemble on a soft level
surface to avoid damaging the
unit or your floor.
•Parts of the assembly may be
easier with 2 people.
•To reduce the
likely hood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
•Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
•From time to time check that
there are no loose screws on
this unit.
•This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
•Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
•Reguraly check andensure
that all bolts and fittings are
tightend properly.
Handy Hints
•Remore all fitting from the

Components - Panels
Please check you have all the panels listed below
2
Legs x4 (5.5x73.2cm)
2
Top Cabinet (70x30x17.3cm)
1
If you have damaged or missing components,
call the Customer Helpline:
Shelf (3.1x24.3x92.6cm)
3

3
M6x65mm Bolt x 12
Ruler - Use this ruler to help correctly identify the screws
Tools required
A
Washer x 12
B
Spring Washer x 12
C
Note:
may be supplied than are required.
Allen Key x 1
D
Components - Fittings
Ruler/tape
measure
Drill
6mm Suitable drill bit
(for use with wall plug)
The quantities below are the correct amount to completed the assembly. In some cases more fittings
Phillips screwdriver
Strap x 1
E
M6x30mm Wall plug x 1
F
G
4x15mm Screw x 2

4
Assembly Instructions
Step 1 a:
Assemble legs
a: Take out drawers.
b: Turn over the top
cabinet on smooth
and clean surface. Attach
legs to top cabinet
by bolts , spring
washers , washers
and Allen key . Do not
tighten the bolts.
1
b:
21
A
BC
D
1
1
2

5
Assembly Instructions
Assemble shelf
a: Attach shelf
3
to
legs as shown by
bolts , spring washers
,washers and Allen
key . Do not tighten
the bolts.
b: Turn over the cabinet.
Tighten all bolts. Put
drawers into cabinet.
Step 2
b:
a:
2
A B
C
D
3

5
Assembly Instructions
Fixing to wall
b: With help, move
Addington Console into
position.
Assembly is completed.
Step 3
b:
a:
It is recommended that
the Addington Console is
fixed to a wall.
a:
hole in product.
Mark fixing hole on wall
and remove Addington
Console.
Drill 6mm hole and insert
wall plug F
Insert screw Gthrough
strap Einto pre - drilled
Before drilling, check wall
for hidden pipes
and cables.
.
Reposition
Addington Console
and fix wall strap using
screw G.
Note: Wall plugs supplied
are for solid walls only.
The correct type of fixing
must be used for your wall
seek professional advice
if in doubt.

When drilling into walls always
check that there are no hidden wires or pipes etc.
You can use one of the following types of wall plug if your walls are made
of brick, breeze block, concrete, stone or wood.
Care &
Maintenance Safety: Always check the fitting
and location to ensure your safety
in and around the home.
Fitting: From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.
If plastic wall plugs
are supplied with your
product :
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
using incorrect fixings is the
responsibility of the installer
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualified
tradesperson if you are unsure.
Hints:
1: General rule: Always us a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5: Ensure wall plugs are well fitted and are a tight fit in the
drilled hole.
No. 1 "General Purpose" wall plug No. 3 "Cavity Fixing" wall plug No. 5 "Hammer Fixing" wall plug
Generally aerated blocks should not
be used to support heavy loads, use
a specialist fitting in this case. For light
loads, general purpose wall plugs can
be used.
No. 2 "Plasterboard" wall plug
For use with plasterboard partitions or
hollow wooden doors. For use with walls stuck with
plasterboard. The hammer fixing allows
it to be fixed to the wall rather than the
plasterboard. Always check the fixing
is secure to the retaining wall.
For use when attaching light loads on
to plasterboard partitions. For use when fitting or supporting
heavy loads such as shelving, wall
cabinets and coat racks.
For use with heavier loads such as TV
& HiFi speakers and satellite dishes etc.
No. 4 "Cavity Fixing-Heavy Duty"
wall plug No. 6 "Shield Anchor" wall plug
Heavy loads
Revision 2 - 7/10/09
A Guide to - Wall Mounting & Fixings
12