Argos Stratford White User manual

Stratford White - 2 Door Wardrobe
Dimensions
Width - 87cm
Depth - 55.1cm
Height - 195.2cm
BK00760 - Issue 1 - 17/07/2014
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 0345 6403030
Assembly Instructions - Please keep for future reference 144/4878

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• Due to difference in floor
levels, doors may not be
aligned. Adjustment may be
necessary.
• To prevent bowing of shelves
do not over load, and always
distribute weight evenly.
• If a residual aroma is
experienced with your new
furniture after the packaging
is removed simply ensure the
room is well ventilated and this
will assist a speedy removal
• We do not
recommend the
use of power drill/
drivers for inserting
screws, as this
could damage the unit. Only use
hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• It is essential that this unit be
fixed to a wall with the fittings
provided.
• Please retain the product label
on the back of the unit, as this
information will help support any
queries.
• Dust with a clean cloth or, if
required a slightly damp cool
cloth. Do not use household
cleaners, abrasives or polishes
as permanent damage may
occur.
• Your furniture is finished to the
required colour. Avoid exposure
to strong sunlight as this can
change the colour. Change in
appearence may also occur if
items are permanently left on a
surface.
• Do not drag the furniture or lift
it by its top.
• Avoid sharp objects, contact
with water and direct heat on all
surfaces
• From time to time check that
there are no loose screws on
this unit.
• Doors should be secured or
removed before moving.
• You should get assistance
when moving or lifting your
furniture. Furniture consisting of
more than one unit should be
disassembled before attempting
to move it.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance - Non compliance with this information may affect your guarantee

Components - Panels
Please check you have all the panels listed below
2
LH cornice return (55.5 x 7cm)
3
Cornice front section (87 x 7cm)
2
RH cornice return (55.5 x 7cm)
4
Assembled wardrobe (191 x 80 x 53.1cm)
1
If you have damaged or missing components,
call the Customer Helpline:
0345 6403030

3
Please check you have all the fittings listed below
Ruler - Use this ruler to help correctly identify the screws
Tools required
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
Components - Fittings
Phillips screwdriver
(medium)
Small
hammer
Step ladder
(or equivalent)
Eye Protection
(when using
hammer)
The following components are pre-fitted and are illustrated for reference only.
20mm handle screw x 2
20mm Dovetail Jointer x 2
A
Wall strap x 1
E
20mm Cornice screw x 7
B
15mm Screw x 1
C
15mm Washer x 2
DF
9mm Dovetail Jointer x 2
White ceramic handle x 2

4
Assembly Instructions
Step 1
Remove and replace
handle
a: Position the unit in
the required position. The
white ceramic handles
are fitted to the inside of
the unit, using a Philips
screwdriver unscrew the
20mm handle screws in
each handle and remove
both the 20mm handle
screw and the white
ceramic handle.
b: Replace the white
ceramic handle on the
front of the unit. Fix in
position by screwing
the 20mm handle screw
into each white ceramic
handle from inside the
unit using a Philips
screwdriver.
20mm Handle screw
a:
b:
1
Philips screwdriver
Philips screwdriver
White ceramic handle
20mm Handle screw
WARNING: Help may be
required for this step.

Assembly Instructions
Step 2
Assemble Cornice
a: Work on a flat clean
surface . Position the RH
cornice return 4and
the cornice front section
2together to make a
corner and press the
20mm dovetail jointer
Acurved edge first into
the deepest slot made
by the two sections and
the 9mm dovetail Binto
the shallowest. Tap home
firmly with a hammer to
make the joint tight.
Repeat for the other joint.
b: Place the cornice
on top of the wardrobe,
you may need to use
step ladders to do this.
position the cornice being
careful to ensure that
the back edges of the
cornhice are flush with
the back of the robe and
that the overhang on
each side is equal. Once
the position is correct,
screw down firmly with a
philips screwdriver and
the 20mm cornice screws
C.
Note: There are not any
pre drilled holes in the
top of the robes for this.
42
A
1
C
5
a:
b:
Small hammer
24
3
Philips screwdriver
WARNING: Help may be
required for this step.
B

6
Assembly Instructions
Step 3
Fixing to wall
It is recommended that
the wardrobe is fixed to
a wall
Fix wall strap Fto the
top of wardrobe using
15mm screw Dand
15mm washer E.
Warning: The
15mm screw D
is for fixing the
wall strap Fto furniture
only. In addition to this
you will need to choose
a screw or fitting which is
suitable for securing the
wall strap Fto the type
of walls you have. If you
are unsure about what
type of screw to use seek
professional help.
Step 4
D
F
E
E
A
B
2
Adjusting doors
1. To adjust the height /
level of the door loosen
all screw ‘A’s on all hinge
plates, level the door
height and retighten all
screw ‘A’s.
2. To adjust the gap
between the doors
loosen screw ‘B’, then
turn screw ‘C’ clockwise
to close the gap or
anticlockwise to increase
the gap. Re-tighten
screw ‘B’ to lock position.
3. To adjust the distance
away from the unit
loosen screw ‘B’, this
allows the hinge arm
to slide back and forth.
Adjust as required then
re-tighten screw ‘B’.
Assembly is complete.
1
3
A
C
Using the correct type of screw
screw through the washer and wall
strap into a pre-drilled hole in the
wall

If you need help or have damaged or missing parts, call the Customer Helpline: 0345 6403030