Argos 615967012 User manual

Ref. no NEM 01.00 Date: 10/10/11
Double wardrobe
A embly In truction - Please keep for future reference
Important - Please read these instructions fully before starting assembly
Dimen ion
For enquirie relating to pare part plea e contact : 08456 400800
Width - 80.2cm
Depth - 54.5cm
Height - 189.7cm
615967012
615967022
615973512
615973522

Safety and care advice
Important - Please read these intructions fully before starting assembly
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Check you have all the
components and tools listed on
pages 3 and 4.
Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight
on the panels, this could cause
damage.
• Assemble the unit as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• If using power tools, please
follow the safety instructions
supplied with the tools.
•We do not
recommend the
use of power drill/
drivers for inserting
screws, as this
could damage the unit. Only use
hand screwdrivers.
• Warning: Before drilling,
check the wall for hidden pipes
and cables.
• Dispose of all packaging
carefully and responsibly.
• Warning: The unit weighs
approximately 56kgs
Please lift with care.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Care and maintenance
Recycling – the packaging materials for this product may
be recycled through your local recycling centre. When you
want to dispose of the product itself, please consider
donating it to a local charitable organisation, otherwise
recycle it through your local recycling centre.
Cleaning instructions
• This product has been
manufactured using modern
manufacturing methods and
materials. With appropriate
in-home care and mainte-
nance it will provide trouble
free performances. Many
domestic multi-purpose
cleaning agents are unsuitable
for use on this product.
The use of aggressive chemi-
cals can result in irreversible
damage. Please follow these
guidelines carefully.
USE only 5% soap, 95%
water solution, wiping with a
damp (not wet) cloth. Finally
dry with a soft clean cloth.
Dust with a soft clean cloth
only.
DO NOT USE wax furniture
polish, abrasive or aggressive
cleaners, bleach or hypochlo-
rate (chlorine) based cleaners,
multi-purpose cleaners,
dilutes, acetone, alcohol,
solvent or similar products.
2

4
Top (80.2 x 54.5cm)
2
Right side
(52 x 187.9cm)
1
Left side
(52 x 187.9cm)
5
Bottom (76.9 x 51.6cm)
10
Left drawer
side
(40 x 16cm)
11
Right drawer
side
(40 x 16cm)
12
Drawer bottom
(73.1 x 39.9cm)
13
Drawer back
(71.95 x 16cm)
9
Drawer front (79.8 x 24cm)
6
Front structural plinth (76.9 x 7.8cm)
7
Shelf (76.9 x 51.6cm)
8
Doors x 2 (155.3 x 39.8cm)
3
Double back panel
(79 x 181cm)
3
Component - Panels
Plea e check you have all the panel li ted below

Wooden dowel x 14
Support foot x 4
Ruler -Usethisruler to help correctly identify thescrews
Tools required
A
Metal dowel x 14
H
Note: The quantities below are thecorrect amount to complete the assembly. In some cases more
fittings may be supplied than are required.
0510 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
EF
N
C
D
L
Q
15mm Screw x 7 35mm Screw x 6
25mm Nail x 30
G
Long locking
nut x 10
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
01234 56
Phillips screwdriver
(medium & large)
Spirit level
Flatblade screwdriver
(medium)
Small
hammer
Ruler/tape
measure
Drill
Ø 5mm Suitable drill bit
Eye protection
(when using a
hammer)
mm
Spacer x 1
I
S
B30mm
30mm Screw x 4
Wedgefix housing x 4 Wedgefix dowel x 4
“L” Bracket x 1
Hanger rail
support x 2
hanging rail x 1
11mm Euroscrew x 4
U1
U2
R
U
12mm Screw x 6
T
V
Fixing block x 1
O
Short locking
nut x 4
B1
Pair of roller runners x 1
Z2
Z1
X1
N N1
Y1
Y
clip hinge x 6
and 15mm Screw x 12
hinge
mounting plate x 6
M
Doorstop x 1
Handle x 3
27mm Connector x 3
P
4MAx15 Connect. screw x 3
Block x 1
25mm Screw x 3
Bumper x 3
Component - Fittings For enquirie relating to pare part plea e
contact : 08456 400800
Plea e check you have all the fitting li ted below
4

Fit wooden dowels .
Attach hinge plates .
Fit metal dowels .
Fit long locking nuts .
Fix runner parts to the
side panel through
holes shown in the detail
view using euroscrews
and screws .
Fit wooden dowels
and long locking nuts
to the plinth .
Fix doorstop to top
with 2 screws .
Fit metal dowels to
top .
Preparation of side
panels
Preparation of top
and plinth
Assembly Instructions
Step 1
Step 2
B
B
Bottom side
Bottom side
Z1
Z1
Z1
B
C
C
C
C
B
B
B
B
C
1
1
2
2
R
Y1
Y1
Y1
A
Front side
Front side
Front side
Z1
U1
R
U1
A
A
A
4
4
6
6
4
A
U1
N
M
M
Y1
B
N
M
5

Attach wedgefix
housing fitting to
shelf .
Preparation of shelf
Assembly Instructions
Step 3
B
B
7
C
5
C
F
7
F
F
Fix wooden dowel c .
Fit long locking nuts .
Preparation of
bottom
Step 4
C
B
6

Position side panels 1
and 2 onto bottom 5
and plinth .
Use a screwdriver to turn
locking nuts b clock-
wise to lock.
Attaching panels
Assembly Instructions
Step 5
Step 6
B
5
6
Position top panel 4
onto the side panels
1 2 .
Use a screwdriver to turn
locking nuts D clock-
wise to lock.
Fix of top panel
4
12
1
2
B
5
6
1
2
B
4
1
2
B
7

U
X1
X1
Attach back panel 3
using 30 nails .
Fit support foot .
Position back panel
.
Fix the block support
as shown, with screw
Assembly Instructions
Step 7
Step 8
3
3
5
56
6
E
D
D
D
Attach back panels
E
3
3
Important:
Cabinet MUST
be “square”
when the back
is attached
U
U
X1
8

Assembly Instructions
Not included
I
H
Top of Unit
W
A
L
L
W
A
L
L
Step 9
Wall fixing
N
To prevent possible
overbalancing we
recommend that this unit
is secured to a suitable
wall by use of the 'L'
Bracket I fitted to the
Top of the unit.
Fix the Bracket I loosely
onto the top of the unit
using spacer I screw R
and mark the wall for the
wall fixing.
Swivel the Bracket away
from the wall and drill a
hole in the wall using a
suitable drill bit and fit
your wall fixing. See wall
mounting & fixings guide
at the back page.
Swivel the Bracket back
and fix the Bracket to the
wall, then tighten Screw
C
I
H
H
Important:
Take care when
drilling the wall
that you do not
drill into any
pipes, wires etc.
If in doubt, consult
an expert.
wall plug and
screw not
included.
N
N
Important:
two people are
needed here.
9

Assembly Instructions
Step 10
Ø5mm
P
O
Fittings have been
supplied in order to join
units together.
If your unit has drawers
you may need to remove
them to reach some of
the holes.
Place units together in
their final positon.
Decide position where to
drill through using a Ø5
mm bit.
Push the Connector K
into the hole and then
screw Bolt J in from the
other side, tighten with a
screwdriver.
P
O
10

Assembly Instructions
Step 14
Fix Wedgefix dowels G
onto the side panels 1
. .
Block the shelf
on the Wedgefix dowels
G as shown.
Fix hanger rail supports
onto the side panels 1
using the screws
Fit the hanging rail
on the supports L as
shown.
Step 11
Attaching shelf
and hanging rail
N
N
L
L
S
L
L
G
G
G
G
F
G
1
2
1
2
7
7
7
S
1
2
S
11

Fit runner
Fix runner part 2 onto the
drawer using 12 mm
screws .
Position fixing block P into
the groove of the drawer
back and screw to fix.
Fix bumper as shown.
Assembly Instructions
Step 12
Step 13
T
T
9
9
U2
U2
U2
R
R
R
Assembling of drawer
box
Fit the RH 14 and LH
13 drawer sides to the
drawer back 15 using
30 mm screws S
Assembling drawer
fronts
Slide drawer bottom
panel 11 into the drawer
box grooves.
Fit short locking nuts E
to the drawer side panels
14 13 .
Insert wooden dowels A
in the drawer side panels
14 13 .
Fit metal dowels B onto
the drawer front .
Position drawer front
2 onto drawer box,
turn locking nuts E
clockwise to lock.
Fit handle using 35mm
screws
10
11
10
11
12
12
A
9
9
T
11
11
11
10
10
10
13
13
13
Z2
B1
B1
B1
B1
A
C
C
C
Z2
Z2
Q
Q
V
V
N1
N1
N1
12

Assembly Instructions
Step 14
Step 15
Fitting hinges to door
Fix 3 hinges to each
door 11 using 15 mm
screws R .
Fix bumpers as shown.
Repeat with all the
doors.
YY
Y
Y
N
N
N
8
8
Insert drawers
Tilt the drawer as shown.
Slide the drawer box along
the runner parts until the
stop.
Wheels and runner parts
have to be correctly
matched as shown.
N
N1
N1
N1
N1
x2
13

Assembly Instructions
Hang door and
fit handles
Important:
The Hinge Arm
must be flat
against the Hinge
Plate.
Step 16
Slot door hinges
onto the hinge plates
tighten screw to lock
hinges in position.
Fit Handles using
35mm screw
See step 17
(Hinge adjustment)
if the doors need adjust-
ment
V
V
V
Q
Q
Q
Q
Q
8
8
Y1
Y1
Y
Y
14

Assembly Instructions
Step 17
A
A
C
Hinge adjustment
Important:
Before adjusting the Doors,
use a spirit level to check
the Base (or Top) of the unit
is levelled front-to-back and
side-to side in the 3
positions shown.
Use suitable packing pieces
(not supplied) to make the
unit levelled BEFORE
making any adjustment to
the hinges as shown.
a: Height adjustment
Loosen screws 'A' on fixing
plates and move door up or
down as required.
Retighten screws 'A'.
b: Forward or backwards
adjustment
Loosen screw 'B' on fixing
plate and move Door in or
out as required.
Retighten screw 'B'.
c: Sideways adjustment
To move Door 'OUT' at
hinge position, slacken
screw 'C' .
To move Door 'IN' at hinge
position, tighten screw 'C'.
a:
B
b:
c:
That's the Robe
completed.
Take care of your unit by
using a damp cloth to
clean it.
Please remember to
occasionally check that
all Cams and Screws are
tight.
15

A Guide to - Wall Mounting & Fixings
Revision 2 - 7/10/09
Important note:
Types of walls
Care &
Maintenance
No.1 “General Purpose” wall plug
No.6 “Shield Anchor” wall plug
Heavy loads
No.3 “Cavity Fixing” wall plug
No.4 “Cavity Fixing-Heavy Duty”
wall plug
No.5 “Hammer Fixing” wall plug
No.2 “Plasterboard” wall plug
Generally aerated blocks should not
be used to support heavy loads, use
loads, general purpose wall plugs can
be used.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
For use with plasterboard partitions or
hollow wooden doors.
heavy loads such as shelving, wall
cabinets and coat racks.
For use with walls stuck with
is secure to the retaining wall.
For use when attaching light loads on
to plasterboard partitions.
Safety: Always check the fitting
and location to ensure your safety
in and around the home.
Fitting: From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.
You can use one of the following types of wall plug if your walls are made
of brick, breeze block, concrete, stone or wood.
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5:
drilled hole.
If plastic wall plugs
are supplied with your
product:
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualified
tradesperson if you are unsure.
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
responsibility of the installer.
16