Argos Pagnell 709/2664 User manual

Assembly Instructions -
Please keep for future reference 709/2664
Dimensions
Depth - 40.5cm
Width - 73cm
Height - 100cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Version 2 Date: 11/03/13
Pagnell Bookshelf

Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority waste
disposal centre.
IMPORTANT: RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
• Argos Ltd. MK9 2 NW. • Regularly check all fastenings
to ensure that they are properly
tightened.
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3.
rom the
plastic bags and separate them
into their groups.
• Keep children and animals away
from the work area, small parts
could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand on the product,
this could cause damage.
• Assemble the item as close to
room) as possible.
• Assemble on a soft level surface
to avoid damaging the unit or your
r.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Do not use this item if any
components are missing or
damaged.
• Assembly to be carried out by
the competent adult only.
• During assembly children should
be kept away from the product due
to the potential risk of injury.
1
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• This product is suitable for
children in the age 6 or above.
• Maximum load:
50 kgs ( top of bookshelf ).

2
Components - Panels
Please check you have all the panels listed below
Top panel (73 x 40cm)
1
If you have damaged or missing components,
call the Customer Helpline: 08456 400800
Finished
front edge
Right side panel
(38 x 98.4cm)
2Left side panel
(38 x 98.4cm)
3
Bottom panel (69.8 x 37.9cm)
4
Shelf x 2 (69.8 x 37.9cm)
5
Back panel (72.4 x 95.2cm)
7
Front panel (69.8 x 4.5cm)
6

3
Note: The quantities below are the correct amount to complete the assembly. in some cases mor
may be supplied than are required.
Components - Fittings
E
C
14mm Screw x 7
A
30mm Dowel x 16
F
Nail x 20
G
Wall plug x 1
B
Plastic support x 3
H
Wall strap x 1 x 1
(This screw is
included in the
bag of wall strap)
15mm Locking nut x 16
110 120 130 140 1500 10 20 30 40 50 60 70 80 90 100
0 1 2 3 4 5 6
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Tools required
Phillips screwdriver
(medium & large)
Small
hammer
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
Ruler - Use this ruler to help correctly identify the screws
Flatblade screwdriver
(medium)
Bradawl
(or sharp point)
D
39mm Locking pin x 16

Assembly Instructions
Step 2
Fitting dowels
a:
a:
Insert Dowels into
the Bottom panel and
Shelves .
4
A
Step 1
b:
Continued on next page.
4
b:
Insert Dowels into
the Right side panel
and Left side panel .
2
A
3
Attaching plastic
supports
a:
Plastic supports onto
the Front panel .
6
C
B
C
BC
BC
B
6
C
B
a:
A
A
A
A
4
A
A
A
A
5 x 2
5
2
3

Assembly Instructions
b:
a:
5
D
Step 4
b:
Front panel onto the
Bottom panel .
6
C
Step 2 -
Step 3
Screw Locking pins
into the Right side panel
and Left side panel
.
2
D
3
Attaching bottom
panel
Fitting locking pins
Position Bottom panel
onto the Left side panel
.
Insert Locking nuts
into the Bottom panel .
Use a screwdriver to turn
Locking nuts clockwise
to lock.
4
E
4
C
C
C
6
4
C
continued
Note:
Insert Locking pins
as far as shown.
Do not over tighten.
3
4
3
4
E
E
E
D
D
D
D
D
D
D
D
D
D
D
D
2
3
back edge
E

Assembly Instructions
a:
6
Step 7
Step 5
Step 6
Continued on next page.
Attaching right side
panel
Attaching shelves
a:
Position Shelves onto
the unit.
Insert Locking nuts
into the Shelves .
Use a screwdriver to turn
Locking nuts clockwise
to lock.
4
E
4
E
5
E
5
E
2
E
5
E
Position Right side panel
onto the unit.
Insert Locking nuts
into the Shelves and
Bottom panel .
Use a screwdriver to turn
Locking nuts clockwise
to lock.
5
5
3
2
5
5
4
4
Screw Locking pins
into the Top panel .
1
D
Attaching top panel
Note:
Insert Locking pins
as far as shown.
Do not over tighten.
D
D
D
D
E
E
E
D
back edge
back edge
1
E
E
E
E
E

Assembly Instructions
b:
7
Step 8
Step 7 -
Fixing back panel
continued
b:
Position Top panel
onto the unit.
Insert Locking nuts
into the Right side panel
and Left side panel
.
Use a screwdriver to turn
Locking nuts clockwise
to lock.
1
E
2
E
4
1
E
E
E
E
back surface
F
7
back edge
2
3
Attach Back panel
onto the unit using Nails
.
F
7
Important:
The unit MUST
be ‘square’ when
back is attached.
E

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
8
Assembly Instructions
It is recommended that
wall.
of top panel using Screw
Fix Wall strap to back
.
With help, move
bookshelf into position.
Warning:
The bookshelf is
heavy.
Lift with care.
and remove bookshelf.
Drill a hole and insert Wall
plug .
Warning:
Before drilling,
check wall for
hidden pipes and
cables.
Reposition bookshelf
Screw .
Fixing to wall
H
wall
C
H
Top panel
G
H
HHG
Note: Wall plugs supplied are
for solid wall only.
be used for your wall, seek
professional advice if in doubt
Back panel
Step
C
G
H
9
Assembly is complete.

A Guide to - Wall Mounting & Fixings
Revision 2 - 7/10/09
Important note:
Types of walls
Care &
Maintenance
No.1 “General Purpose” wall plug
No.6 “Shield Anchor” wall plug
Heavy loads
No.3 “Cavity Fixing” wall plug
No.4 “Cavity Fixing-Heavy Duty”
wall plug
No.5 “Hammer Fixing” wall plug
No.2 “Plasterboard” wall plug
Generally aerated blocks should not
be used to support heavy loads, use
a specialist tting in this case. For light
loads, general purpose wall plugs can
be used.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
For use with plasterboard partitions or
hollow wooden doors.
For use when tting or supporting
heavy loads such as shelving, wall
cabinets and coat racks.
For use with walls stuck with
plasterboard. The hammer xing allows
it to be xed to the wall rather than the
plasterboard. Always check the xing
is secure to the retaining wall.
For use when attaching light loads on
to plasterboard partitions.
Safety: Always check the fitting
and location to ensure your safety
in and around the home.
Fitting: From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.
You can use one of the following types of wall plug if your walls are made
of brick, breeze block, concrete, stone or wood.
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5: Ensure wall plugs are well tted and are a tight t in the
drilled hole.
If plastic wall plugs
are supplied with your
product:
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualified
tradesperson if you are unsure.
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
using incorrect xings is the
responsibility of the installer.