Argos Malibu 305/1764 User manual

MADE IN
BRITAIN
Dimensions
Width - 39cm
Depth - 40cm
Height - 92.5cm
Malibu - 5 Drawer Chest
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 2 - 30/09/13
Important - Please read these instructions fully before starting assembly
ALR2845
305/1764
305/1757
305/1740
305/1771
305/1733
Issue 2 - 30/09/13 - Drawer Front code corrected to D2034A

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 16.5kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
1
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Top (D2029A)
(388 x 396mm)
Rail (D2032A)
(349 x 92mm) x 2
Cross Rail (D2033A)
(349 x 88mm) x 2
Left Side (D2030A)
(910 x 394mm)
6
2
3
4
Right Side (D2031A)
(910 x 394mm)
8
Drawer Wrap (W161)
(943 x 95mm) x 5
Drawer Base (T161)
(299 x 330mm) x 5
7
9
5
Back (X954)
(333 x 373mm)
Drawer Front (D2034A)
(345 x 157mm) x 5

Please check you have all the fittings listed below
Tools required
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 10
B
Metal dowel (F901) x 14
C
D
Large locking
nut (F900) x 4
E
Small locking
nut (F3) x 10
F
H I
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Nail (F51) x 10
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Electric drill
(only use when
drilling into walls)
25mm Screw (F50) x 5
R (F601)
L (F600)
F599
F599
K
Drawer stops (F599) x 10
Runners (F600) x 5 and (F601) x 5
Handle (F631) x 5
Bracket (F327) x 1
13mm Screw (F79) x 1
G
J
40mm Screw (F910) x 8

Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
x 5
x 5
x 5
x 5
Prepare the drawer
fronts and wraps
a: Screw 2 metal dowels
. into the holes shown
on the back of the 5
drawer fronts .
Note: Tighten metal
dowels up fully against
the panel.
b: Insert 2 small locking
nuts into the holes
shown on the 5 drawer
wraps .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
B
6
a:
b:
F
7
B
Assemble the drawers
a: Place drawer base
into the narrow slot on
the drawer wrap .
Fold wrap around the
base.
b: Turn drawer wrap
assembly over and push
onto the back of the
drawer front .
Note: Turn locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
8 8
7
6
F
B
B
B
6
7
7
7
7
B
F
a:
b:
B
F
7
F
F
Step 2
6
6

Assembly Instructions
5
Step 3
Attach the drawer
stops
Carefully break off 2
drawer stops (F599) from
a set of drawer runners
. .
Push the drawer stops
fully through the drawer
wrap from the inside.
K
SNAP!
SNAP!
F599
7
7
Attach the handles
Attach a handle to
each of the 5 drawer
fronts using screw .
Note: Do not
overtighten the screws.
I
H
K
K
F599
K
F599
K
F599
K
H
Step 4
x 5
x 5
6
6
I

Assembly Instructions
6
Step 5
Prepare the left side
Separate the runners .
Push fit the left runners
marked ‘L’ into the left
side .
Note: Runners must be
be fitted flat against the
panel. If necessary
gently tap into final
position.
Insert 2 large locking
nuts into the left side
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Tap a wooden dowel
into the left side .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
1
K
K
E
A
K
K
L
F600
K
K
K
K
E
E
E
1
1
A
10mm
A
1
Finished
front edge
A
R
F601
K
K
K
K
K
K
E
E
Prepare the right side
Push fit the right runners
. marked ‘R’ into the
right side .
Insert 2 large locking
nuts into the right
side .
Tap a wooden dowel
into the right side .
2
K
E
A
2
2
Finished
front edge
2
Step 6

Finished
front edge
G
G
A
A
Assembly Instructions
7
Step 7
Prepare the rails
Tap 2 wooden dowels
into each of the rails .
A
A
A
4
Prepare the cross rails
Tap 2 wooden dowels
into each of the the
cross rails .
Step 9
Step 8
A
5
x 2
Fit the rails to the
right side
Push the rails onto
the right side and
secure them with 2
screws .
plain chipboard
surface
plain chipboard
surface
plain chipboard
surface
plain chipboard
surface
4
4
Rail (349 x 92mm)
2
4
2
G
Cross Rail
(349 x 88mm)
4
5
x 2

Finished
front edge
G
G
Assembly Instructions
8
Step 10
plain chipboard
surface
plain chipboard
surface
Step 11
Fit the cross rails
Push the cross rails
onto the right side
and secure them with 2
screws .
5
2
G
5
2
5
G
G
G
G
1
Fit the left side
Push the left side
onto the assembly and
secure it with 4 screws .
G
1

Assembly Instructions
9
Step 12
Step 13
Prepare the top
Screw 4 metal dowels
into the top .
Fix the bracket in the
middle of the top ,
flush to the back edge,
using screw .
B
B
B
B
Finished
front edge
plain
chipboard
surface
3
J
C
B
3
J
C
3
Fit the top
Push the top onto
the side panels and
. .
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the side panels and
. .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
3
1
2
1
2
E
E
B
E
3
1
2
Finished
front edge