Argos Phoenix 719/3147 User manual

Assembly Instructions - Please keep for future reference
Dimensions
Width - 35cm
Depth - 35cm
Height - 35cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Phoenix 1 Cube Unit
issue 1 9/02/’10
719/3147
719/1101

We do not
recommend the use
of power drill/ drivers
for inserting screws,
as this could damage
the unit. Only use hand
screwdrivers.
Warning: The unit weighs
approximately 5.5kgs.
Please lift with care.
●Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
●From time to time check that
there are no loose screws on this
unit.
●This product should not be
discarded with household waste.
Take to your local authority waste
disposal centre.
1
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Care and maintenance
Check you have all the
components and tools listed on
pages 2 and 3.
plastic bags and separate them
into their groups.
Remove all fittings from the
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand on the panels, this
could cause damage.
Assemble the unit as close to its
final position (in the same room)
as possible.
Assemble on a soft level
surface to avoid damaging the unit
or your floor.
Parts of the assembly will be
easier with 2 people.
Dispose of all packaging carefully
and responsibly.
Assembly to be carried out by
the competent adult only.
During assembly children
should be kept away from the
product due to the potential risk of
injury.
Do not use this item if any
components are missing or
damaged.
“IMPORTANT: RETAIN THESE
INSTRUCTIONS FOR FUTURE
REFERENCE”.
Argos Ltd. MK9 2NW. This product is suitable for
children in the age of 6 or above.
Regularly check all fastenings
to ensure that they are properly
tightened.
The maximum weight of the
children user: 50kgs.

Components - Panels
Please check you have all the panels listed below
2
Shelf x 2 (32 x 34.9cm)
1Back (34.8 x 34.8cm)
3
Side x 2 (35 x 35cm)
2
If you have damaged or missing components,
call the Customer Helpline:08456 400800
15mm Screw x 12
Phillips screwdriver
(medium & large)
Ruler/tape
measure
Components - Fittings
Please check you have all the fittings listed below
Tools required
Ruler - Use this ruler to help correctly identify the screws
B
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
45mm Screw x 8
A
Cap x 8
C
Wall strap x 1
D
12mm Screw x 1
EF
Wall plug x 1
26mm Screw x 1
G
Metal plate x 1
H

A
Assembly Instructions
Step 1
Fitting the shelves
a:
Step 1
a: Use Screws to fix
the Sides , onto
Shelves .
Use Caps to cover the
holes on the unit.
A
b:
1
b: Use Screws to fix
Back onto the unit.
B
C
3
1
2
2
2
1
C
3
B
3
c: Place the unit to the
desired location.
c:
Unfinished edge
Assembly is complete.

Assembly Instructions
If you need help or have damaged or missing parts, call the Customer Helpline : 08456 400800
4
J
H
D
F
G
Example of different configuration
It is strongly recommended
that the unit is attached to
the wall using Wall straps
C .
D
b: Use Screw to fix the
Wall strap onto the
back of the unit .
c: With help, place the
unit in the intend position.
d: Drill a hole in the wall
at an appropriate position
and insert Wall plug
(Masonry walls only).
To secure the unit, fix
Wall strap to the wall
using Screw (Masonry
walls only).
E
D
D
F
G
Note: It would be useful to
ask someone to help you
at this stage.
Important: When drilling
into walls always check
that there are no hidden
wires or pipes etc. Make
sure that the screws and
wall plugs supplied are
suitable for supporting
the unit. Consult a
qualified tradesperson if
you are not sure.
Fixing with another unit
HB
a: Use Screws to fix
the Metal plate of link
another unit from the
back.
B
H
E

A Guide to - Wall Mounting & Fixings
Revision 2 - 7/10/09
Important note:
Types of walls
Care &
Maintenance
No.1 “General Purpose” wall plug
No.6 “Shield Anchor” wall plug
Heavy loads
No.3 “Cavity Fixing” wall plug
No.4 “Cavity Fixing-Heavy Duty”
wall plug
No.5 “Hammer Fixing” wall plug
No.2 “Plasterboard” wall plug
Generally aerated blocks should not
be used to support heavy loads, use
a specialist ftting in this case. For light
loads, general purpose wall plugs can
be used.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
For use with plasterboard partitions or
hollow wooden doors.
For use when ftting or supporting
heavy loads such as shelving, wall
cabinets and coat racks.
For use with walls stuck with
plasterboard. The hammer fxing allows
it to be fxed to the wall rather than the
plasterboard. Always check the fxing
is secure to the retaining wall.
For use when attaching light loads on
to plasterboard partitions.
Safety: Always check the ftting
and location to ensure your safety
in and around the home.
Fitting: From time to time check
the ftting to ensure the wall plugs
or screws do not become loose.
You can use one of the following types of wall plug if your walls are made
of brick, breeze block, concrete, stone or wood.
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5: Ensure wall plugs are well ftted and are a tight ft in the
drilled hole.
If plastic wall plugs
are supplied with your
product:
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualifed
tradesperson if you are unsure.
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
using incorrect fxings is the
responsibility of the installer.

Assembly Instructions -
Please keep for future reference 719/1101
719/3147
Dimensions
Depth - 35.5cm
Width - 35cm
Height - 35cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Version 2 Date: 23/10/13

• Argos Ltd. MK9 2 NW. • This product is suitable for
children in the age 6 or above.
• Maximum load: 20 kgs.
• Regularly check all fastenings
to ensure that they are properly
tightened.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority waste
disposal centre.
IMPORTANT: RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3.
rom the
plastic bags and separate them
into their groups.
• Keep children and animals away
from the work area, small parts
could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand on the product,
this could cause damage.
• Assemble the item as close to
room) as possible.
• Assemble on a soft level surface
to avoid damaging the unit or your
r.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Do not use this item if any
components are missing or
damaged.
• Assembly to be carried out by
the competent adult only.
• During assembly children should
be kept away from the product due
to the potential risk of injury.
1
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.

2
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components,
call the Customer Helpline: 08456 400800
Top/Bottom panel x 2 (34.9 x 34.9cm)
1
Side panel x 2 (31.8 x 34.9cm)
2
Back panel x 1 (34.5 x 34.5cm)
3

3
Note: The quantities below are the correct amount to complete the assembly. in some cases mor
may be supplied than are required.
Components - Fittings
ABC
Nail x 8 Screw cover x 450mm Screw x 8
110 120 130 140 1500 10 20 30 40 50 60 70 80 90 100
0 1 2 3 4 5 6
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Tools required
Phillips screwdriver
(medium & large)
Small
hammer
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
Ruler - Use this ruler to help correctly identify the screws
Flatblade screwdriver
(medium)
D
33mm Screw x 1
E
Wall strap x 2
F
Wall plug x 1
14mm Screw x 3
G
Note E G : Please keep the

Assembly Instructions
Attaching unit
a:
Step 1
4
Top panel onto the
Side panels .
A
1
2
Use Screw covers
Q to
cover the screw heads.
C
b:
Bottom panel onto the
unit.
A
1
a:
b:
1
2
2
A
A
A
A
Unnished
back edge
1
2
2
A
A
A
C
C
C
A
C
Unnished
back edge

Assembly Instructions
5
Step2
Step 3
Fixing back panel
panel onto the unit.
B
3
B
3
12
Finishing the unit
With help, place the unit in
the intended position.
back surface
Back
Important:
The unit MUST
be ‘square’ when
the back is attached.

Assembly Instructions
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Fixing with another unit
With help, move the unit
remove the unit.
Drill a hole and insert Wall
plug .
Reposition
Fixing to wall
Warning:
The unit is heavy.
Lift with care.
Warning:
Before drilling,
check wall for
hidden pipes
and cables.
F
D
G
E
It is recommended that the
Wall strap to link
another unit from the
back.
into position.
strap using Screw .
strap onto the top panel.
G
E
U
S
6
X 2
Step 4
G
E
G
a: b:
a:
b:
wall
G
E
Top panel
F
D
DEF
Note: Wall plugs supplied are
for solid wall only.
be used for your wall, seek
professional advice if in doubt

A Guide to - Wall Mounting & Fixings
Revision 2 - 7/10/09
Important note:
Types of walls
Care &
Maintenance
No.1 “General Purpose” wall plug
No.6 “Shield Anchor” wall plug
Heavy loads
No.3 “Cavity Fixing” wall plug
No.4 “Cavity Fixing-Heavy Duty”
wall plug
No.5 “Hammer Fixing” wall plug
No.2 “Plasterboard” wall plug
Generally aerated blocks should not
be used to support heavy loads, use
loads, general purpose wall plugs can
be used.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
For use with plasterboard partitions or
hollow wooden doors.
heavy loads such as shelving, wall
cabinets and coat racks.
For use with walls stuck with
is secure to the retaining wall.
For use when attaching light loads on
to plasterboard partitions.
Safety: Always check the fitting
and location to ensure your safety
in and around the home.
Fitting: From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.
You can use one of the following types of wall plug if your walls are made
of brick, breeze block, concrete, stone or wood.
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5:
drilled hole.
If plastic wall plugs
are supplied with your
product:
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualified
tradesperson if you are unsure.
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
responsibility of the installer.

MADE IN
BRITAIN
Dimensions
Width - 35cm
Depth - 35cm
Height - 35cm
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 2 - 19/08/13
Important - Please read these instructions fully before starting assembly
ALR2900
719/3147
Phoenix - 1 Cube Unit
Issue 1 was not produced by Dec and so, there are slight differences to panels and kit.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 5.5kgs.
Please lift with care.
• Check you have all the
components and tools listed on
page 2.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• Parts of the assembly will be
easier with 2 people.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
strap supplied.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
12 3
80%
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Tools required
Rule Scissors
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Please check you have all the fittings listed below
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A B C
D
Electric drill
(do not use for
fitting screws)
45mm Screw (F65) x 8 13mm Screw (F63) x 4 Plate (F587) x 1
Strap Screw Washer x 2
Overbalance protector kit (F269) x 1
E
Nail (F51) x 10
Top/Base (D2403A)
(320 x 349mm) x 2
Side (D2404A)
(350 x 350mm) x 2
Back (X345-345)
(345 x 345mm)
F
Cover Cap (F939) x 8

A
A
A
Assembly Instructions
3
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Join the top and base
to one side
Fix the top and base
to one side using 4
screws .
Note: The arrows
indicate the finished
edges of the panels.
A
Step 1
Step 2
1
2
Fit the back
Place the back ,
coloured surface facing
down, onto the unfinished
edges of the unit and
secure it using the 10
nails .
3
Step 3
E
Fit the other side
Fit the remaining side
to the top and base
using 4 screws .
Note: The arrows
indicate the finished
edges of the panel.
1
A
2
A
A
A
A
1
1
2
1
1
2
3
Fit the back
Place the back ,
coloured surface facing
down, onto the unfinished
edges of the unit and
secure using 8 screws .
3
Step 3
B
BB
BB
B
BB
B
BB
B
BB
3
E

Assembly Instructions
4
Step 4
To join the cubes and
fit the overbalance
protector
The cube can be joined
to another cube using
the plate supplied to
create a larger unit.
Place the cubes
together, making sure
that the back edges are
flush with one another.
Fix the plate over the
2 units to be joined using
4 screws .
To prevent possible
overbalancing we
recommend that this unit
is secured to a suitable
wall by use of the
overbalance protector kit
. fitted to the unit or an
alternative fixing method
of your choice.
Wall fixings are not
supplied as they will
need to suit the wall
type.
Warning: Take
care when
drilling the wall that you
do not drill into any
pipes, wires etc. If in
doubt, consult an expert.
1 Cube Unit
2 Cube Unit
2+2 Cube Unit
4 Cube Unit
The cubes can be joined in any combination.
Here is an example.
Strap
Washer
Screw
(not supplied)
Wall fixing
(not supplied)
Wall
Wall
Fit the other end of the strap to the wall
D
Strap
Washer
Screw
Fit one end of the strap to a
suitable position on the cube
D
C
C
B
D
B
C
x 4

Assembly Instructions
F
F
F
5
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 5
Fit the cover caps
Peel off the cover caps
from their backing paper
and stick them over the
head of the screws on
the sides .
Assembly is complete
Step 6
F
F
F
F
F
2
2
2