Argos Harrogate Multimedia CD760 User manual

ASSEMBLY INSTRUCTIONS Components parts and fittings contained in the box
Harrogate Multimedia CD760 Component Parts List Fittings
A
Large screw x 12
Easy Assembly Instructions
BSmall screw x 8
C
Shelf support x 32
DStability brackets x 8
1 – Top
Before you
start, here is
some helpful
advice
1. We suggest that you spend a short time reading through this leaflet
and then follow the simple step by step instructions.
2. This item should be attached to the wall with the enclosed strap for
safety reasons before use. Due to the wide variety in types of walls,
the necessary wall screw & rawl plug are not provided.Please read
and follow the enclosed wall fixing guide carefully so that you can be
sure you use the appropriate screw and rawl plug for your type of wall.
3. Do not discard any of the packaging until you have checked that you
have all the components and fittings needed for assembly and in
case the product is returned to the supplier for whatever reason.
4. Assemble the unit on a carpet, to avoid scratching the unit.
5. Keep all fittings and glue out of reach of children.
6. All you need to assemble the unit is an appropriate screwdriver.
2 – Base
3 – Left Side FScrew covers x 8
4 – Right Side
5 – Centre Shelf
6-7 – Back Panels
8-15 – Adjustable Shelves
E Wall Fixing Pack x 1
12
859
200
1600
Help Line : 08456 400 800
X 2 X 2 X 2 X 2

ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS
Harrogate Multimedia CD760 Harrogate Multimedia CD760
1. Attach the two sides
(part 3 & 4) to the base
(part 2) using four large
screws (part A). Ensure
that the removable arrows
on the two sides are
pointing up and the
grooves for the back are
as per the diagram.
2. Slide the back (part 6)
into place ensuring the
oak surface is visible
from the front of the unit.
3. Attach the center shelf
(part 5) to the unit using
four large screws (part A).
Ensure that the back (part 6)
fits neatly into all of the
grooves.
4. Slide the other back
(part 7) into position,
ensuring it too fits neatly
into all of the grooves.
34

ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS
Harrogate Multimedia CD760 Harrogate Multimedia CD760
5. Attach the top (part 1)
to the unit using the
remaining four large
screws (part A).
Attach the screw covers
(part F) to the 8 visible
screw heads
6. Attach the adjustable
shelves (part 8~15) using
the shelf supports (part C).
56

ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS
Harrogate Multimedia CD760 Harrogate Multimedia CD760
7. Attach the stability
brackets (part D) to the
unit using the small
screws (part B). Attach
the screw covers (part F)
to the 8 visible screw
heads.
8. We strongly recommend
that the unit is attached to
the wall using the Fixing
Pack (E) provided. Place the
unit against the wall in its
final desired location, note
where the wall screw will
need to fixed into the wall.
Attach the wall strap to the
unit using the small screw
as per the diagram. Using
a suitable drill bit attach the
strap to the wall using the
screw and rawl plug
provided (make sure the
rawl plug supplied is
suitable for the wall, if not
please use a suitable rawl
plug).
78

Harrogate Multimedia CD760
Dimensions
Width - 85.9cm
Depth - 20cm
Height - 160cm
Issue 1 - 9/07/08
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
875/1935
Assembly Instructions - Please keep for future reference

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: If required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all ttings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its nal position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your oor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws ,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
Glue safety - Take care when using glue, please follow the advice below

Please check you have all the panels listed below
2
Top
1
(16.1 x 86cm)
Base
2
(20 x 86cm)
Centre Shelf
5
(15.85 x 80.7cm)
Left side panels
3
(16 x 157cm)
Right side panels
4
(16 x 157cm)
Back board x 2
6~7
(78.5 x 81.4cm)
Components - Panels If you have damaged or missing components,
call the Customer Helpline: 08456 400800
Adjustable Shelves x 8
8~15
(13.8 x 80.5cm)

3
Please check you have all the ttings listed below
38mm Large screw x 12
A
14mm Small screw x 8
B
Shelf support x 32
C
Note: The quantities below are the correct amount to complete the assembly. In some cases more ttings
may be supplied than are required.
Components - Fittings
Stability brackets x 8
D
Screw covers x 8
F
Wall Strap x 2 12mm Screw x 2
Plug x 2 32mm Screw x 2
E
Tools required
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Small
hammer
Ruler/tape
measure
Drill
Eye protection
(when using a
hammer or glue)
7mm Suitable drill bit
(for use with wall plug)
01 02 03 04 05 06 07 08 09 0 100 110 120 130 140 150
01 23 45 6
Ruler - Use this ruler to help correctly identify the screws
100 20 30 40 50 60 70 80 90 100
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105

4
Assembly Instructions
Step 1
Bottom assembly
Attach the two sides &
to the base using
four large screws .
Ensure that the removable
arrows on the two sides
are pointing up and the
grooves for the back are
as per the diagram.
3
A
6
42
2
A
2
A
4
A
3
Attaching back panel
Slide the back into
place ensuring the oak
surface is visible from the
front of the unit.
6
Step 2