Argos Canterbury 517/0571 User manual

Canterbury 5+2 CHEST
Assembly Instructions - Please keep for future reference
509/4334
476/9086
517/0571
Dimensions
Width - 84.3cm
Depth - 41.9cm
Height - 144.5cm
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0845 6400800
71932 Version A Date 09/11/2015
25 Kg
55 lbs
max
5 Kg
11 lbs
9 Kg
20 lbs

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Check you have all the
components and tools listed on
the following pages.
• Remove all ttings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to lay out the parts before
starting.
• During assembly, do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its nal position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your oor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the use
of power drivers for
inserting screws, as
this could damage
the unit. Only use hand screw
drivers.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
Glue safety - Take care when using glue, please follow the advice below
• The provided tip-over restraint
must be installed in order to
optimize user safety.
Safety

Components - Panels
Please check you have all the panels listed below
2
If you have damaged or missing components, call the
Customer Helpline: Argos = 0845 6400800
EG
EF
A 00489 Left drawer side
(34.5 x 14cm) x7
B 00488 Right drawer side
(34.5 x 14cm ) x7
C 02743 Drawer back
( 32.1 x 14cm) x2
D02744 Drawer back
(70.6 x 14cm) x5
P06056 Drawer bottom
(33.3 x 34.2cm) x2
R06057 Drawer bottom
(71.8 x 34.2cm) x5
S09783 Back panel
(142.1 x 76.4cm)
K 76425 Profile side
(41.5 x 2.5cm) x2
M 76426 Profile side
(41.5 x 2.5cm) x2
N 76315 Profile front
(83.5 x 2.5 cm) x2
FY Side panel L/R
(141.2 x 39 cm) x2
LA Top panel (84.3 x 41.9cm)
IA Bottom panel (84.3 x 41.9cm)
(25.6 x 35.2 cm)
EE Drawer front
(75.1 x 22.1cm) x5
O 76316 Base rail
(75.4 x 3.1 cm)
Drawer front, left
(37.4 x 22.1cm)Drawer front, right
(37.4 x 22.1cm)
DDivider panel

3
Please check you have all the ttings listed below
Drawer fastener x28
Flat head screw (ø4 x 13mm) x15
Handle x12
Cam x24
Note: The quantities below are the correct amount to complete the assembly. In some cases more ttings
may be supplied than are required.
Dowel (ø5 x 30mm) x17
Panel clips x8
Machine screw (M4 x 20mm) x12
Flat head screw (ø3,5 x 15mm) x14
Strap x2
Wedges x4
Components - Fittings
Ruler - Use this ruler to help correctly identify the screws
Tools required
10401 11011
20203 20228 22601
25233 25440
26228
31687 33204
81040 94009
41435
94066
Flat head screw (ø6,3 x 27mm) x7
26033
Drawer runner x14
Machine screw (M4 x 15mm) x28
26221
Cam bolt x24
31513
63008
Floor glider x4
Stabilizer x1
Glue x1
Tape dots x1
Drawer support x14
17414
Flat head screw (ø5,8 x 9mm) x30
26020
10510
Drawer bottom support x5
Cross head screwdriver
(medium & large)
Wooden block
Tape measure
Flathead screwdriver
(medium)
Ruler
Eye protection
(when using a
hammer or glue)
01 02 03 04 05 06 07 08 09 0 100 110 120 130 140 150
01 23 45 6
Hammer

5
Assembly Instructions
Step 1
Step 2
Insert dowles Dowel
# 20203 X10
Insert dowels 20203 into
outer holes on the ends
of side panel FY and
divider panel G .
Place cam 31687 into
the holes on top of side
panel FY and divider
panel G .
Arrow facing the edge of
the panel.
Fittings you will need for this step:
Fittings you will need for this step:
Cam bolt
# 31513 X10
Insert cam bolts
Insert cam bolts 31513
into the holes on top and
bottom panel LA and
IA . Also insert cam bolts
in center holes of the top
panel LA . See detail
drawing.
Cam bolt must be
screwed ush down.
Cam
# 31687 X10
(X2)
FY
LA
IA
G
4

6
Assembly Instructions
Step 3
Fittings you will need for this step:
Flat head screw
# 26020 X24
Flat head screw
# 25233 X12
Drawer runner
# 41435 X12
FY FY
12
10
8
5
3
1
FY
FY
1.
2.
3.
Place drawer runners
Extend drawer glide
41435 . Place at head
screw 26020 through
the correct holes at the
back of the drawer glide,
into the holes on the side
panels FY .
Tighten screw but do not
overtighten.
Close slide until the front
hole is visible through
the oval slot on the slide.
Place at head screw
26020 thorugh the hole in
the slot into the hole on
the panel.
Tighten screw but do not
overtighten.
Attach the at head
screw 25233 into hole in
drawer glide.
Repeat this step for each
of the remaining runners.
5

Assembly Instructions
7
Step 4
Attaching drawer run-
ners
Fittings you will need for this step:
Drawer runner
# # 41435 X2
Flat head screw
# 26020 X4
Flat head screw
# 25233 X2
Step 5
G
3.
2.
1.
FY
FY
IA
Extend drawer glide
41435 . Place at head
screw 26020 through
the correct holes at the
back of the drawer glide,
into the holes on the side
panels G.
Tighten screw but do not
overtighten.
Close slide until the front
hole is visible through
the oval slot on the slide.
Place at head screw
26020 thorugh the hole in
the slot into the hole on
the panel.
Tighten screw but do not
overtighten.
Attach the at head
screw 25233 into hole in
drawer glide.
Repeat this step on other
side of divider panel G.
Attaching bottom panel
Place cam bolts from the
bottom panel IA into
the holes in the end of
side panels FY .
Make sure the nished
edge is facing toward
the front and that the
unnished side is facing
toward the bottom of the
cabinet.
Tighten the cams.
6

LA
G
Attaching back panel
Slide the back panel S
smoothly down into the
grooves in the side and
bottom panel FY + IA .
Assembly Instructions
8
Step 6
Step 7
FY
FY
IA
S
Attaching divider panel
Press down divider panel
Gtowards the top panel
LA . Make sure the
nished edge is facing
toward the front .
Tighten cams with a
screwdriver, as shown.
7
Unnish face

Assembly Instructions
Step 8
9
Step 9
Gathering proles
Insert wedges 33204
into slots on the angle
ends of side and front
proles K + N+ M .
Use a hammer.
Fittings you will need for this step:
Wedges
# 33204 X4
M
K
N
FY
IA
LA
FY
G
x2
S
Attaching top panel
Place the cam bolts from
top panel LA into the
end holes on side panel
FY . Tighten cams.
Top
Bottom
8

Insert dowels 20203
into outer holes on the
gathering proles. Use
glue 22601 as shown.
Assembly Instructions
Gathering proles to
cabinet
Step 11
Step 10
10
Gathering proles
Fittings you will need for this step:
Fittings you will need for this step:
Push the prole down
as it reaches the bottom
panel IA . Use at head
screw 26033 to tighten.
Flat head screw
# 26033 X7
Glue
# 22601 X1
FY
N
K
M
S
LA FY
IA
G
Dowel
# 20203 X7
9