Argos Wooden Filer User manual

Assembly Instructions - Please keep for future reference
-
227/6966
Dimensions
Width - 39cm
Depth - 39.5cm
Height - 80cm
Important
Version 1 Date: 28/04/14
Wooden Filer
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
- Please read these instructions fully before starting assembly

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
Glue safety - Take care when using glue, please follow the advice below
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
that all bolts and fittings are
tightend properly.
Handy Hints

Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline:
Argos = 0345 6400800
Left side panel
(38.9 x 78.3cm)
2Back panel
(38.5 x 76cm)
3
Right side panel
(38.9 x 78.3cm)
1
Pilot holes
for guidance
only
2
Top panel
(39 x 39cm)
4
Front bottom panel
(35.8 x 11cm)
5
Large drawer right side
(34 x 26cm)
14
Large drawer left side
(34 x 26cm)
15
Drawer bottom x 4
(33.6 x 33.6cm)
17
Large drawer back
(32.6 x 26cm)
16
Front panel
(35.8 x 5cm)
8
Middle panel
(35.8 x 11cm)
6
Back bottom panel
(35.8 x 11cm)
7
Small drawer front x 3
(35.1 x 13.8cm)
9
(35.1 x 30cm)
Large drawer front
13
Small drawer right side
x 3 (34 x 11.5cm)
10
Small drawer left side
x 3 (34 x 11.5cm)
11
Small drawer back
x 3 (32.6 x 11.5cm)
12
Finished front edge

3
Ruler - Use this ruler to help correctly identify the screws
Tools required
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Small
hammer
Ruler/tape
measure
Drill
Eye protection
(when using a
hammer or glue)
7mm Suitable drill bit
(for use with wall plug)
The screws length is measured from the head to the point (30mm screw shown).
Please check you have all the fittings listed below
Runner x 8
A
14mm Screw x 5
E
12mm Screw x 24
B
Nail x 14
H
30mm Dowel x 8
C
12mm Locking nut x 16
I
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
Plastic support x 2
F
39mm Locking pin x 26
D
Plastic file support x 2
K
Wall strap x 1
O
15mm Locking nut x 10
G
Glue x 1
J
Components - Fittings
(This Screw is included
in the bag of runner)
Handle x 4
M
12mm Screw x 8
N
P
30mm Screw x 24
L
(This screw is
included in the
wall strap bag)
x 1
Wall plug x 1

4
Assembly Instructions
Step 1
a:
b:
Continued on next page.
A
B
A
A
A
A
A
A
A
A
1
D
D
D
C
B
B
B
B
B
B
B
B
D
B
A
B
1
Pilot holes for
runner position
Middle hole
1
A
BMiddle hole 1
B
B
B
B
C
J
J
1.7cm
Finished front edge
Position Runners in
front edge of the Right
side panel .
Runners on the Right
side panel .
Slide top of the Runners
Use screws to fix the
back.
Attaching runners
a:
1
A
A
A
B
1
Slide top of Runners
shown using Screws .
Insert Dowels into the
Right side panel .
Screw Locking pins(3pcs)
forward and fix as
b:
A
B
C
into the Right side
panel .
Note: Insert locking pins
as far as shown.
Do not over tighten.
1
1
Place a small amount of
Glue into the dowel
holes.
J
D

5
Assembly Instructions
c:
d:
Step - continued1
B
A
B
B
B
B
A
A
A
A
A
A
A
A
2
D
B
A
B
2
D
D
B
B
C
J
B
B
B
B
B
B
Pilot holes for
runner position
Middle hole 2
Middle hole
2
C
J
1.7cm
Finished
front edge
D
back.
c:
Position Runners in
front edge of the Left side
panel .
2
A
Slide top of the Runners
A
Runners on the Left
side
panel .
Use screws to fix the
A
B
2
Slide top of Runners
shown using Screws .
forward and fix as
Insert Dowels into the
Left side panel .
Screw 3 Locking pins
the Left side panel
.
d:
A
B
C
into
D
Note: Insert locking pins
as far as shown.
Do not over tighten.
2
2
Place a small amount of
Glue into the dowel
holes.
J

6
Assembly Instructions
Step 2
a:
b:
b:
Continued on next page.
Step 3
a:
Unfinished
back edge
E
E
FF
F
E
E
E
C
J
C
C
C
5
5
8
6
2
5
8
G
G
J
C
C
7
Finished
front edge
C
J
C
J
J
Attaching plastic
supports
a:
Plastic supports onto
the Front bottom panel
.
Front bottom panel
onto the Front panel .
Use Screws to fix
Use Screws to fix
E
5
F
b: E
5
8
Attaching bottom panel
and support panel
Insert Locking nuts
into the Front bottom
panel .
G
5
b: Position Front bottom
panel and and Front
panel onto the Left
side panel .
5
8
2
G
Use a screwdriver to turn
Locking nuts
clockwise to lock.
Front bottom panel .
5
Insert Dowels into the
C
a:
Place a small amount of
Glue into the dowel
holes.
J
Middle panel and
Back bottom panel .
6
7
Insert Dowels into the
C
Place a small amount
of Glue into the dowel
holes.
J

7
Assembly Instructions
c:
d:
continuedStep 3 -
6
7
6
2
7
5
1
G
G
G
G
G
Unfinished
back edge
G
G
Insert Locking nuts
into the Middle panel
and Back bottom panel
.
G
6
7
c: Position Middle panel
and Back bottom panel
onto the Left side
panel .
2
Use a screwdriver to turn
Locking nuts
clockwise to lock.
G
Insert Locking nuts
into the Front bottom
panel , Middle panel
and Back bottom panel
.
G
5
6
7
G
Use a screwdriver to turn
Locking nuts
clockwise to lock.
6
7
d: Position Right side
panel onto the unit.
1

8
Assembly Instructions
a:
b:
Step 4
G
D
Unfinished
back edge
G
G
G
G
4
2
1
4
D
D
D
D
Note:
Insert Locking pins
as far as shown.
Do not over tighten.
D
into the Top panel .
4
a: Screw Locking pins
Attaching top panel
b: Carefully locate the
Top panel onto the
unit.
4
Insert 4 Locking nuts
into the unit.
G
Use a screwdriver to turn
Locking nuts clockwise
to lock.
G

9
Assembly Instructions
Step 5
a:
Continued on next page.
Step 6
9
3
H
D
D
D
D
D
Unfinished
back surface
Important:
The unit MUST
be ‘square’ when
back is attached.
Fixing back panel
Attach Back panel
onto the unit using Nails
.
H
3
Note:
Insert Locking pins
as far as shown.
Do not over tighten.
D
into the Small drawer front
.
9
a: Screw Locking pins
Small drawer assembly