Argos Seville 171/8140 User manual

Assembly Instructions - Please keep for future reference
Issue 2 - 12/12/13
Ruler - Use this ruler to help correctly identify the screws
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
MADE IN
BRITAIN
If you need help or have damaged or missing parts, call the Customer Helpline: 0870 112 1928
or email: [email protected] (quoting your original order number)
Important - Please read these instructions fully before starting assembly
Dimensions
Seville - Bedside
ALR2908
171/8140
145/0446
157/3622
170/9214
Width - 35.5cm
Depth - 33cm
Height - 41.5cm
160/9785
162/9325
162/7956
159/7732
Issue 2 - 12/12/13 - New cat codes added

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 7kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

2
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email:
[email protected] (quoting your original order number
and the reference numbers below)
12 3 Top/Base (D2493A)
(321 x 327mm) x 2
Left Side (D2494A)
(412 x 328mm)
Right Side (D2495A)
(412 x 328mm)
Drawer Front (D2496A)
(317 x 157mm)
Left Drawer Side (W410LH)
(300 x 95mm)
Right Drawer Side (W410RH)
(300 x 95mm)
Drawer Back (W288-95)
(288 x 95mm)
Drawer Base (T299-297)
(299 x 297mm) Back (X175-347)
(175 x 347mm)
4 5 6
7
8
9

Glue Safety - Take care when using glue, please follow the advice below
Skin contact: Remove contami-
nation by washing with soap and
water. This procedure should be
followed prior to aeting and
drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
3
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• From time to time check that
there are no loose screws on
this unit.
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email:
[email protected] (quoting your original order number
and the reference numbers below)
Tools required
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
A
Wooden dowel (F22) x 4
B
Metal dowel (F901) x 2
C
D E F
G
Small locking
nut (F3) x 2
Nail (F51) x 540mm Screw (F910) x 8
Handle (F300) x 1
H
Knock-in Peg (F171WH) x 4
IR (F601)
L (F600)
F599
F599
Drawer stops (F599) x 2
Runners (F600) x 1 and (F601) x 1
25mm Screw (F95) x 1

4
F
Step 1
Assembly Instructions
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email:
[email protected] (quoting your original order number
and the reference numbers below)
B
C
Prepare the drawer
front
Screw 2 metal dowels
into the holes shown on
the back of the drawer
front .
Note: Tighten metal
dowels up fully against
the panels.
B
4
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .
Note: Arrow on locking
nut must point towards
hole in edge of panel.
C
5
6
Step 2
C
5
C
6
B
B
4
Step 3
Attach the drawer
sides to the drawer
front
Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
5
6
4
C
C
5
6
B
B
C
Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on
either surface of the drawer sides.
Make sure that the small groove
is on the inside, as shown.
4
5
6
Small
groove
Plain chipboard
surface

Assembly Instructions
5
Step 4
H
H
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
8
5 6
4
7
5 6
8
7
7
H
5 6
8
5
6
4
6
6
5
6
5
SNAP!
SNAP!
F599
I
I
F599
I
Step 6
Push in drawer stops
Carefully break off the 2
drawer stops (F599) from
the drawer runners .
Push the drawer stops
fully through the drawer
sides and from
the inside.
I
5 6
F599
I
F599
I
H
H
7
8
299mm

Finished
front edge
Assembly Instructions
6
Step 7
Attach the handle
Attach the handle to
the drawer front
using screw .
4
G
E
Prepare the left side
Separate the runners .
Push fit the left runner
marked ‘L’ into the left
side .
Note: Runners must be
be fitted flat against the
panel. If necessary
gently tap into final
position.
I
I
1
Step 8
Prepare the right side
Push fit the left runner
marked ‘R’ into the right
side .
Note: Runners must be
be fitted flat against the
panel. If necessary
gently tap into final
position.
I
2
Step 9
L
F600
I
R
F601
I
G
E
4
I
1
I
Finished
front edge
2

D
D
Finished
front edge Finished
front edge
D
D
Assembly Instructions
7
Step 10
Step 11
Prepare the top and
the base
Tap 2 wooden dowels
into the top and the
base .
A
3
3
Join the top to the
right side
Push the top onto
the right side and
secure with 2 screws .
Step 12
3
2
D
A
A
Plain chipboard
surface
3
Finished
front edge
23
x 2
Finished
front edge
3
Join the base to the
right side
Push the base onto
the right side and
secure with 2 screws .
3
2
D

Assembly Instructions
8
Step 13
Fit the left side
Push the left side
onto the assembly and
secure with 4 screws .
1
D
D
D
D
D
1
Step 14
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the 3
edges of the back as
shown.
Stand the unit up for
the next step.
9
F
9
yy
x
x
b:
F
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
9

Assembly Instructions
9
If you need help or have damaged or missing parts, call the Customer Helpline: 0870 112 1928
or email: [email protected] (quoting your original order number and the reference numbers on the component pages)
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Insert the drawer
Lift the front of the
drawer whilst inserting to
overcome the ‘stop’
system.
Note: To ensure that
your drawer runs
smoothly, spray a small
amount of furniture
polish into the grooves.
Assembly is complete
Step 15