Argos Yanniek 483/4124 User manual

Dimensions
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Assembly Instructions - Please keep for future reference
Tip : To prevent damage,
we recommend that you
build your unit on the
carton(s) it was packed in.
Height - 67.0 cm
Depth - 91.0 cm
Width - 197.8 cm
Yanniek Bed 90x190
Argos = 03456 400 800
483/4124
459/7344
459/7344 WHITE
483/4124 OAK
Issue: 1 - 19/11/15
DR82152

1
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
•
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
that all bolts and fi ttings are
tightend properly.
Handy Hints
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
Glue safety - Take care when using glue, please follow the advice below•
Important – Please read these instructions fully before starting assembly
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• Check you have all the
components and tools listed
on the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Assembly should be carried out
by a competent adult only.
• do not use this item if any
components are missing
or damaged.
• this item is suitable for childeren
from the age of 6.
Safety and Care Advice

Please check you have all the panels listed below
Components - Panels If you have damaged or missing components,
call the Customer Helpline:
2
03456 400 800
Footboard
(955 x 670 x 34 mm)
P8997
19
Back
(1908 x 411 x 3 mm)
BO2686
1
Drawer base x 2
(516 x 280 x 3 mm)
BO3101
2
Drawer back x 2
(506 x 120 x 12 mm)
LA1654
3
Left drawer side x 2
(280 x 120 x 12 mm)
LA1655
4
Right drawer side x 2
(280 x 120 x 12 mm)
LA1656
5
Shelf
(801 x 280 x 22 mm)
P1018
6Storage bottom
(1910 x 315 x 15 mm)
P1019
7
Storage top
(1910 x 315 x 15 mm)
P1020
8
Bedbase
(1910 x 670 x 18 mm)
P1021
9
Small bedbase
(1910 x 235 x 18 mm)
P1022
10
Plinth
(1900 x 60 x 28 mm)
P1876
11
Storage side left
(387 x 299 x 15 mm)
P2695
12 Storage side right
(387 x 299 x 15 mm)
P2696
13
Door front
(550 x 382 x 15 mm)
P3716
14
Front panel
(1910 x 122 x 18 mm)
P4751
15
Rear panel
(1910 x 282 x 15 mm)
P4752
16
Drawer front x 2
(550 x 189 x 15 mm)
P4753
17
Headboard
(955 x 670 x 34 mm)
P8996
18

Please check you have all the fittings listed below
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
Tools required
Eye protection
(when using a
hammer or glue)
Ruler/tape
measure
0102030405060708090 100 110 120 130 140 150
0123456
Small
hammer
Setsquare
Spirit level
Drill
7mm Suitable drill bit
(for use with wall plug)
Flatblade screwdriver
(medium)
Phillips screwdriver
(medium & large)
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
The screwslength ismeasured from thehead to the point (30mm screw shown).
3
12mm 15mm
Runner x 4
PM16951
U
Shelf/door handle x 3 (128mm)
GR1957
T
Screw x 4 (M4x9mm)
FK1981
S
Plug x 12
FK1800
R
Nail holder x 1
FK1415
Q
Wooden dowel x 8 (8x30mm)
FK1411
P
Chipboard screw x 36 (4x30mm)
FK1322
O
Pozi screw x 4 (4x12.5mm)
FK1309
N
Drawer fixing screws x 8 (6.3x10mm)
FK1301
M
Hinge back x 2
FK12641
L
Hinge door x 2
FK1240
K
Shelf support x 1 (5x15mm)
FK1201
J
Connector x 6 (20x12mm)
FK1016
I
Small locking screw x 6 (5x11mm)
FK10561
H
Allen key x 1 (3mm)
FK1013
G
Large locking nut x 12 (15x12mm)
FK1012
F
Locking screw x 16 (5x24mm)
FK1011
E
Locking nut x 4 (12x10mm)
FK1010
D
Confirmat screw x 23 (5x40mm)
FK1005
C
Foot x 4
FA1706
B
Nail x 30
FA1515
A
Glue x 1
FA1510
W

Assembly Instructions
4
Finished
front edge
8
J
F
F
F
F
F
F
F
F
180˚
Finished
front edge
Finished
front edge
Finished
front edge
F
13
P
P
P
P
12 U
M
M
MM
U
13
C
C
C
C
6
12
7
8
G
Finished
front edge
Finished
front edge
Step 1
Step 2
a:
b:
a:
b:
b: Attach left @and right
storage sides #with 4
confirmat screws Cto the
shelf 6using allen key G.
Preparing storage
sides
a: Insert 4 wooden dowels
Pwith a small amount of
glue Winto the holes of
left @and right storage
sides #.
Fix runners Uon left storage
side @as shown using
4 drawer fixing screws M.
Make sure the arrow on the
runner is pointing to the
finished front edge.
Assembling storage
unit
a: Insert 8 large locking
nuts Finto storage bottom
7and top 8where shown.
Make sure the ‘arrow’
on the large locking nuts F
are pointing towards the
holes in the edges of 7
and 8.
b: Turn over the storage top
8and insert shelf support
J.
Continued on next page.
U
U
M
M
1.
2.
W
P

W
P
Finished
front edge
RH
E
Finished
front edge Finished
front edge
Finished
front edge
15
P
P
P
P
13 8
C
C
C
CC
C
C
C
712
L
L
19
E
E
E
E
E
E
R
R
R
R
R
H
H
H
L
c:
a:
b:
Assembly Instructions
5
Step 2 continued
Step 3
c: Attach storage bottom
7and top 8with 8
confirmat screws Cto the
storage sides @and #
using allen key G.
Inserting fittings
a: Insert 4 wooden dowels
Pwith a small amount of
glue Win the holes of
front panel %.
b: Insert 5 plugs Rin
footboard (.
Screw 3 small locking
screws Hand 6 locking
screws Ein footboard (.
Followed by screwing 2
back hinges Lin footboard
(.

Assembly Instructions
6
19
8
7
19
8
15
15
W
J
Finished
front edge
F
F
F
F
Step 4
a:
b:
b: Put drop of glue Win the
2 holes of footboard (
before sliding them onto the
dowels of front panel %.
Make sure front panel %is
placed beneath shelf
support Jas is shown.
Attaching panels
a: Use a screwdriver to
turn the 4 locking nuts F
in storage top 8and
bottom 7clockwise to
lock on footboard (.

Assembly Instructions
7
Step 5
E
E
EE
E
E
H
H
H
18
R
R
R
R
R
R
R
b:
a:
RH
E
b: Insert 7 plugs Rin
headboard *.
Screw 3 small locking
screws Hand 6 locking
screws Ein headboard *.
Followed by attaching the
runners Uwith 4 drawer
fixing screws M.
Make sure the arrow on the
runner is pointing to the
finished front edge.
M
M
M
M
U
U
Preparing panels
a: Attach plinth !to
rear panel ^with 5
confirmat screws Cusing
allen key G.
Insert 4 large locking
nuts Finto rear panel ^
where shown.
Make sure the ‘arrow’
on Fis pointing towards
the hole in the edge of
rear panel ^.
Finished
front edge
Finished
front edge
F
16
11
F
F
F
F
C
C
C
C
C
U
U
M
M
1.
2.

Assembly Instructions
8
Step 6
8
7
16
18
C
C
C
C
C
C
8
a:
b:
15
Assembling main body
a: Connect the rear panel
^to the footboard (
and use a screwdriver to
turn the 2 locking nuts F.
Let another person hold
the rear panel ^while
connecting the headboard
*to the rear panel ^,
storage top 8and bottom
7.
Use a screwdriver to
turn the 6 locking nuts F.
b: Fix the front panel %to
the storage top 8with 6
confirmat screws Cusing
allen key G.
19
F
F
FF
F
F
F
F

Assembly Instructions
9
Step 7
8
10 O
OO
O
O
O
O
O
O
O
Step 8
a:
Continued on next page.
Assembling support
boards
a: Flip the unit from its
side with two persons.
Use 8 chipboard screws
Oto attach small bedbase
0to the storage top 8,
make sure to position
the small support board
against the front panel %.
Note: there are no pre-
drilled holes for the
chipboard screws O.
Fitting back panel
Attach back 1to the back
of the storagebox with the
coloured surface facing the
inside of the unit using nails
A.
Use nail holder Qto hold
the nails vertical and at
correct distance as you
secure the back. The nails
should be spaced about
150 mm apart.
Attach the 4 feet Bon the
storage bottom 7using 12
chipboard screws O.
Note: there are no pre-
drilled holes for the
chipboard screws O.
15
90˚
19
A
A
A
A
A
A
A
A
A
A
A
AA
A
AA
A
A
A
A
A
A
A
A
A
A
B
B
B
B
1
7O
O
O
O
O
OO
O
O
O
O
O
18
AA
O
O
O
B
A
Q