Argos HOME New Pagnell 622/1168 User manual

Dimensions
Width - 100cm
Depth - 48.5cm
Height - 71.5cm
New Pagnell Desk
Assembly Instructions - Please keep for future reference 622/1168
618/7202
Important - Please read these instructions fully before starting assembly
Version 1 Date: 09/11/16
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
606/9447

Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Safety and Care Advice
Important –Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
Glue safety - Take care when using glue, please follow the advice below
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
that all bolts and fittings are
tightend properly.
Handy Hints
• Do not use this item if any
components are missing or
damaged.
• Parts of the assembly will be
easier with 2 people.
• Argos Ltd. MK9 2 NW. • This product is intended for
children in the age 6 or above.
• Maximum load:
50 kgs (top of desk).
• Assembly of this product must
be carried out by a competent
adult.
IMPORTANT: RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
• During assembly children
should be kept away from the
product due to possible risk of
injury.

2
Pilot holes
for guidance
only
Finished front edge
Table top (100 x 48cm)
1
Right side panel
(46 x 70cm)
4
Top support (58.5 x 11cm)
2
Bottom support (58.5 x 11cm)
3
Middle panel
(46 x 70cm)
5Left side panel
(46 x 70cm)
6
Front support
(36.7 x 11cm)
7Drawer right side
x 2 (34 x 11.5cm)
11
Back support
(36.7 x 11cm)
8
Front panel
(36.7 x 4.5cm)
9
Drawer front x 2
(36 x 14.4cm)
10
Drawer left side
x 2 (34 x 11.5cm)
12
Drawer back
x 2 (33.5 x 11.5cm)
13
Large drawer
front (36 x 33.6cm)
15
Large drawer right
side (34 x 24cm)
16
Large drawer left
side (34 x 24cm)
17
Large drawer back
(33.5 x 24cm)
18
Back panel (60 x 39.4cm)
19
Drawer bottom
x 3 (33.6 x 34.4cm)
14
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline:
Argos = 0345 6400800

Note:
14mm Screw x 4
Nail x 12
Components - Fittings
E
J
3
The quantities below are the correct amount to complete the assembly. In some cases mor
may be supplied than are required.
(This Screw is included
in the bag of runner)
A
Runner x 6
B
12mm Screw x 18
C
30mm Dowel x 13
D
Plastic support x 2
F
39mm Locking pin x 22
G
15mm Locking nut x 10
H
50mm Screw x 8
I
Screw cover x 4
K
12mm Locking nut x 12
L
Glue x 1
M
30mm Screw x 12
N
12mm Screw x 6
Ruler - Use this ruler to help correctly identify the screws
Tools required
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Small
hammer
Ruler/tape
measure
Drill
Eye protection
(when using a
hammer or glue)
7mm Suitable drill bit
(for use with wall plug)
The screws length is measured from the head to the point (30mm screw shown).

Assembly Instructions
Step 1
4
a:
b:
Continued on next page.
4
A
B
A
B
A
B
4
B
B
B
B
B
F
F
Pilot holes for
runner position
Finished
front edge
F
Attaching runners
Note:
The front part of
the runner should be
approximately 1.7cm
from the front edge of the
panel.
a: Position Runners in
front edge of the Right
side panel .
4
Runners on the Right
side panel .
A
Slide top of the Runners
A
A
B
4
.
C
C
C
b: Slide top of Runners
forward and x as
shown using Screws .
A
B
Insert Dowels into the
Right side panel .
C
Screw Locking pins
into the Right side panel
.
F
Note: Insert locking pins
as far as shown.
Do not over tighten.
4
4
B
A
B
Middle hole
1.7cm
4
A
B
BMiddle hole
4

Assembly Instructions
5
5
B
A
Pilot holes for
runner position
Step - continued1
Note:
The front part of
the runner should be
approximately 1.7cm
from the front edge of the
panel.
c: Position Runners in
front edge of the Middle
panel .
5
A
d: Slide top of Runners
forward and x as
shown using Screws .
A
Insert Dowels into the
Middle panel .
C
5
Runners on the Middle
panel .
Slide top of the Runners
A
A
B
5
.
B
B
A
B
A
B
A
5
B
B
A
B
B
A
B
C
C
C
d:
c:
A
BB
Middle hole
A
BMiddle hole
1.7cm
5
5
Finished
front edge

Assembly Instructions
Step 2
Fitting dowels and
locking pins
6
a:
b:
F
C
C
CC
C
C
C
F
F
8
7
3
2
6
2
3
Insert Dowels into
the Top support ,
Bottom support ,
Front support and
Back support .
b:
C
7
8
a:
Insert Dowels into
the Left side panel .
C
Screw Locking pins
into the Left side panel
.
F
Note: Insert locking pins
as far as shown.
Do not over tighten.
6
6

Assembly Instructions
Step 3
Attaching plastic
supports
b:
a:
7
Step 4
E
E
D
D
9
E
E
9
7
8
7
4
a:
Plastic supports onto
the Front panel .
E
9
D
b:
Front panel onto the
Front support .
E
9
7
E
D
G
G
Attaching bottom
panel and back
support
a: Position Front support
and Back support
onto the Right side panel
.
Insert Locking nuts
into the Front support
and Back support .
G
7
7
4
G
Use a screwdriver to turn
Locking nuts
clockwise to lock.
back edge
8
8
E
G

Assembly Instructions
Step 5
a:
Middle panel onto the
unit.
HH
8
Attaching middle panel
a:
b:
H
I
I
H
H
H
H
H
H
5
8
7
5
2
3
Use Screw covers to
cover the screw heads.
H
5
I
H
3
2
b:
Top support and
Bottom support onto
the Middle panel .
back edge
5
Finished
front edge

Assembly Instructions
Step 7
Step 6
9
Note:
Insert Locking pins
as far as shown.
Do not over tighten.
F
1
a: Screw Locking pins
into the Table top .
Insert 2 Locking nuts
into the Top support
and Bottom support .
G
3
a:
Attaching table top
Use a screwdriver to turn
Locking nuts clockwise
to lock.
G
b:
Continued on next page.
F
2
Attaching left side
panel
G
G
F
F
F
F
F
F
G
G
3
2
6
1
1
4
5
6
b: Then carefully locate
the Table top onto
the unit.
1
Insert 6 Locking nuts
into the unit.
G
Use a screwdriver to turn
Locking nuts clockwise
to lock.
G
back edge
back edge
Position Left side panel
onto the unit.
6
G
G
G
G