Argos Perth 392/9652 User manual

Perth Dining Chair
Assembly Instructions - Please keep for future reference 392/9652
Issue 1 - 31/03/15
Dimensions
Width - 42cm
Depth - 42cm
Height - 85.5cm
423/8029
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 640 0800

1
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Parts of the assembly will be
easier with 2 people.
• During assembly do not stand
or put weight on the product, this
could cause damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Do not stand on the chair.
• Do not use this chair as step
ladder.
• To reduce the
likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Unit weight: 3.4 kgs.
• Maximum safe weight of user:
110kgs.
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Care and maintenance
Handy Hints
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the
bolts.
• Regularly check and ensure
that all bolts and fittings are
tightend properly.

2
Components - Parts
Components - Fittings
Please check you have all the parts listed below
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
Backrest
(32.5 x 5 x 39.5cm)
3
Upper leg
(54.5 x 3 x 59cm)
1Lower leg
(54.5 x 3 x 59cm)
2
Seat
(38.5 x 38.5 x 4cm)
4
Ruler - Use this ruler to help correctly identify the screws
0 15 30 45 60 75 905 20 35 50 65 80 9510 25 40 55 70 85 100 120 140105 125 145110 130 150115 135 155 160 165 170
Allen key x 1
M6 x 15mm Bolt x 4
A B C
M6 x 35mm Bolt x 5
If you have damaged or missing components, call the
Customer Helpline: Argos = 0345 640 0800

Attaching seat
Place the seat face
down on a flat and raised
surface such as a table.
Position the chair frame
on the seat as shown
then fix through holes
using bolts then
tighten with allen key .
Important:
Carefully turn
over the chair.
Place it on a flat
even surface and
make adjustments
to ensure the legs
are even on the
floor.
Then fully tighten
bolts fixed on
step 1 using allen
key .
Assembly is complete.
3
Assembly Instructions
Step 1
A
A
A
A
A
A
B
B
B
B
B
2
2
1
2
4
4
4
B
C
C
B
1
3
3
1
2
Attaching backrest
Position the upper leg
and lower leg in a
crossed position as
shown.
With the help of an
assistant holding the
legs, insert the legs
into holes on the
backrest as shown.
Then fix through holes
using bolts and tighten
with allen key .
Important:
Do not fully
tighten the bolts
at this stage.
A
A
C
1
2
3
Step 2
4
4
B
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 640 0800