Argos HOME Doublebed White 4Ft User manual

Doublebed White - 4Ft
Dimensions
Length - 195,3cm
Depth - 126,3cm
Height - 92,6cm
Weight - 22kg
Issue 2 - 01/06/17
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
0045 7668 8055 or e-mail: order@flexa.dk
Assembly Instructions - Please keep for future reference 7037076

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could
damage the unit. Only use hand
screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1

2
Endrail x2
(111,7x8,9x2,0cm)
Midsupport x2
(93,6x8,9x2,0cm) Leg x1 (24,7x4,3x4,3cm)
Endrail x2
(117,7x6,5x2,0cm) Endrail x2 (117,7x8,9x2,0cm)
7
10 11
8 9
Leg x2 (33,4x4,3x4,3cm)
3
Components - Parts
Please check you have all the parts listed below
Leg x2 (92,6x4,3x4,3cm)
1
Bedside x4 (91,2x8,9x2,0cm)
4
No. 12-04303341-20
Leg x2 (33,4x4,3x4,3cm)
2No. 12-04303342-20
List x4 (90,4x2,0x2,0cm)
5No. 12-02009041 Slat x14 (119,7x6,5x1,5cm) 6No. 12-01511972
No. 12-02011772-20
No. 12-02009361 No. 12-04302471
No. 12-02011774-20 No. 12-02011773-20
If you have damaged or missing components,
call the Customer Helpline:
0045 7668 8055
No. 12-04309261-20
No. 12-02009122-20

Components - Fittings
Please check you have all the fittings listed below
M6x90mm Connecting bolt x4
Tools required
A
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
M6 ø14x13mm Barrel nut x4
B
E
4,0x30mm Chipboard screw x42
C
10x45mm Dowel x24 4,0x35mm Chipboard screw x205x40mm Dowel x4
D
Phillips
screwdriver
(medium)
Small
hammer
Allen key
4mm incl.
Flatblade
screwdriver
(medium)
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
G
J
F
H
K
N
I
L
O
M8x10mm Grub screw x4
Ø10 Cover cap White x4
4,0x60mm Chipboard screw x2
M4x65mm Threaded pin x2
M4/Ø8x38mm Connecting bolt x4
4,0x20mm Chipboard screw x12
No. 3930-05040
No. 3921-04065
No. 4020-001
No. 3903-40020
No. 3938-00010-2
No. 3901-40060
No. 4008-013
Q
M8/Ø30 Washer x2
No. 3928-000083
3
No. 3901-40030
No. 3930-10045
No. 3922-06013
No. 3913-06090
No. 4033-004
No. 3903-40035
No. 3917-08010No. 3909-63090
No. 3933-14016
No. 4022-012
6,3x90mm Assembly screw x12
Ø14x15,5mm Threaded bush x4
15 gram Glue tube x2
48x48x40mm Angle x2
M
P

4
Assembly Instructions
8
88
4
5 5
1
1
1
7
7
7
9
D
D
D
D
D
D
M
M
M
G
G
G
G
G
G
E
E
F
F
F
F
F
E
D
F
G
G
3
3
9
G
G
One hole up!
One hole up!
Insert the Ø10 dowels D
into the holes in bedsides
4and endrails 7and
8.
It may be necessary
to tap the dowels in
very gently with a small
hammer.
Apply glue Mto the list
5and attach it to the
bedside 4using screws
F. Repeat for all four
bedsides.
Apply a small amount of
glue Minto the 2 small
holes in legs 1before
the small dowels Eare
gently hammered in.
Attach endrails 7, 8
and 9between legs 1
using screws G.
Don’t overtighten.
Attach endrail 9
between legs 3using
screws G.
Don’t overtighten.
Step 1
Step 3
Step 2
Step 4

4
4
2
2
L
L
J
J
H
H
I
Assembly Instructions
I
L
J
H
Push the threaded pin
Ithrough the middle
hole in leg 2. Attach
connecting bolts Lto the
pin.
Note the position of the
holes in connecting
bolt L.
Insert threaded bushes
Jinto the holes in the
bedsides 4. Connect
the bedsides 4to
the leg 2. Fasten the
bedsides by tightening
the grub screws Hin the
threaded bushes J.
Attach the assembled
bedsides by placing the
dowels into the holes in
legs 1and 3.
Push barrel nuts Binto
the holes in bedsides 4
. Put the washer Qon
the 2 connecting bolts
Awhich are used to
attach the headboard.
Push connecting bolt A
through legs 1and 3
to meet the barrel nuts B
and fasten with the allen
key.
Step 6
Step 7
Step 5
5
4
4
4
4
4
1
1
3
3
A
A
A
Q
Q
A
B
B
B
B
B
A
B
Q

Assembly Instructions
Step 8
Step 9
Attach angles Pto the
lower endrails using
screws O.
Attach midsupports
10 to the angles using
screws O. Attach the
midsupports 10 to the
leg 11 using screws N.P
O
N
10
10
11
N
6
P
PP
O
4 mm.
568,5 mm.568,5 mm.
O
O
P

Assembly Instructions
Position three slats 6
into the bed with the
distances shown. Push
the bedsides together
and fasten the slats using
screws C.
Position the remaining
slats 6into the bed with
the distance of 65 mm
between one another.
Fasten the slats using
screws C.
Assembly is complete.
Step 10
If you need help or have damaged or missing parts, call the Customer Helpline: 0045 7668 8055
E-mail: order@flexa.dk
Ref.no. 44-01688-20 B Stand: 010617 Page 9 (80-12201-20)
C C C
C
C
65 mm
65 mm 65 mm 65 mm
715 mm
6 66
C
C
66666666666
Step 11
7