Argos Venetia 630/3505 User manual

Dimensions
Venetia - 1 Drawer Bedside
Assembly Instructions - Please keep for future reference
Issue 2 - 29/07/13
Ruler - Use this ruler to help correctly identify the screws
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
630/3505
630/3512
632/5394
632/5404
632/5411
632/5428
630/3495
630/3488
ALR2529
Width - 38.5cm
Depth - 36cm
Height - 42cm
18/10/10 - Additional codes added because they are being supplied for home delivery and stocked-in.
25/01/11 - Corrected the front page dimensions.
MADE IN
BRITAIN
If you need help or have damaged or missing parts, call the Customer Helpline: 0870 112 1928
or email: [email protected] (quoting your original order number)
Important - Please read these instructions fully before starting assembly
Issue 2 - 29/07/13 - Click have agreed with Argos to put their help line number on the Venetia range as a trial.
Range title changed from Napoli to Venetia.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: These units weigh
approximately 8kgs. Please lift
with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the units.
Only use hand screwdrivers.
• Safety note: If there is any
chance of these units being
pulled over by children etc. it is
recommended that the units are
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.

2
100%
Left Side (D0622A)
(399 x 353mm)
1Right Side (D0623A)
(399 x 353mm)
2
Plinth (D0022A)
(349 x 80mm)
6Drawer Front (D0624A)
(345 x 157mm)
11 Back (X776)
(371 x 331mm)
Top (D0020A)
(382 x 356mm)
3
5
Base (D0625A)
(349 x 351mm)
4
7Drawer Back (W410B)
(319 x 105mm)
Left Drawer Side (W410LH)
(300 x 95mm)
10
8Right Drawer Side (W410RH)
(300 x 95mm)
9
Drawer Base (T410)
(330 x 297mm)
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email:
[email protected] (quoting your original order number
and the reference numbers below)

3
A
Wooden dowel (F22) x 6
C
Nail holder (F149) x 1
D
G
40mm Screw (F910) x 6
H
25mm Screw (F50) x 2
Nail (F51) x 10
Tools required
F
Large locking
nut (F900) x 2
Small locking
nut (F3) x 2
E
B
Metal dowel (F901) x 4
JR (F601)
L (F600)
F599
F599
Drawer stops (F599) x 2
Runners (F600) x 1 and (F601) x 1
Rule Scissors Hammer Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
I
Handle (F236) x 1
45mm Screw (F65) x 4
K
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email:
[email protected] (quoting your original order number
and the reference numbers below)

4
F
Step 1
80%
x1
K
K
B
E
Prepare the drawer
front
Screw 2 metal dowels
into the holes shown on
the back of the drawer
front .
Note: Tighten metal
dowels up fully against
the panels.
B
6
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .
Note: Arrow on locking
nut must point towards
hole in edge of panel.
E
7
8
Assemble the drawer
sides and back
Fit the left drawer side
and right drawer side
to the drawer back
using 4 screws .
Note: Line up the small
grooves on the inside of
the drawer assembly.
K
7
8
9
Step 3
Fit the drawer base
Slide the drawer
base along the small
grooves of the drawer
sides and into the
groove of the drawer
back .
10
7 8
9
Step 4
E
K
K
7
7
8
9
Small
groove
E
8
B
B
10
7
8
9
6
Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.
Assembly Instructions
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email:
[email protected] (quoting your original order number
and the reference numbers below)
Step 2

Assembly Instructions
5
Step 5
Push the drawer stops
into the drawer wrap
Carefully break off the 2
drawer stops (F599) from
the pair of drawer
runners .
Push the drawer stops
fully through from the
inside of the drawer
sides and .
J
7 8
Attach the drawer
front
Turn the drawer
assembly over and push
onto the back of the
drawer front .
Note: Turn locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
6
E
B
E
6
Step 6
Attach the handle
Attach the handle to
the drawer front
using 2 screws .
I
H
Step 7
66
SNAP!
SNAP!
F599
J
J
F599
J
F599
J
F599
J
I
H
H
7
8
Note: The locking nuts can be on
either surface of the drawer sides.

A
Assembly Instructions
6
Step 8
G
G
Fit plinth to right side
Attach plinth to the
right side using the
dowel already fitted and
secure with screw .
Step 5
6
2
Finished
surface
Prepare the left and
right side
Separate the runners .
a: Push fit the left
runner marked ‘L’ into
the holes shown on the
left side .
Note: Runners must be
be fitted flat against the
panel. If necessary
gently tap into final
position.
Insert a large locking
nut as shown.
Note: Arrow on locking
nut must point towards
hole in edge of panel.
Tap in wooden dowel
as shown.
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
b: Push the right
runner marked ‘R’
into the holes shown on
the right side .
Insert a large locking
nut as shown.
Tap in wooden dowel
as shown.
1
J
F
2
F
J
J
A
A
L
F600
JF
R
F601
J
10mm
A
a:
b:
F
A
J
1
Finished
front edge
F
J
Finished
front edge
2

G
G
A
A
Assembly Instructions
Step 9
7
Step 10
A
Plain chipboard
surface
5
A
G
A
Prepare the base
Tap a wooden dowel
into each side of the
base .
4
A
Prepare the plinth
Tap a wooden dowel
into each end of the
plinth .
Step 11
Fit the base and the
plinth to the right side
Attach the base to
the right side using
the dowel already fitted
and secure with 2
screws .
Attach the plinth to
the right side using
the dowel already fitted
and secure with a screw
. .
5
Plain chipboard
surface
4
4
2
2
G
5
G
4
2
5

Assembly Instructions
8
Step 12
Fit the top
Push the top onto
side panels and .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the inside of the side
panels and .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
3
1 2
1 2
F
F
Fit the left side
Attach the left side to
the assembly and secure
with 3 screws .
Prepare the top
Screw 2 metal dowels
into the holes shown on
the top .
Step 13
Step 14
B
3
G
G
G
1
G
Plain chipboard
surface
B
B
B
3
3
1
1
2

Assembly Instructions
Step 15
9
11
C
D
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
C
D
b:
Fit the back panel
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
down onto the unit, as
shown.
Use the nail guide to
hold the nails vertical
and at the correct
distance whilst you nail
around the sides of the
back .
Note: Nails should
be spaced about 150mm
apart.
Stand the unit up for
the next stage.
11
11
C
D
x
x
yy
11