Argos Zest 280/6769 User manual

MADE IN
BRITAIN
Dimensions
Width - 40cm
Depth - 40cm
Height - 43.5cm
Zest - Bedside
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 3 - 02/10/14
Important - Please read these instructions fully before starting assembly
ALR3041
280/6769
Issue 2 - 02/07/14 - Cat Code changed to 280/6769.
Screws for the feet changed to F81 (SC2800).
Amended the assembly so that the base panel is now fitted before the feet.
Issue 3 - 02/10/14 - Range name changed to Zest

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 11kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Components - Panels
Please check you have all the panels listed below
2
12 3
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Top (D2946A)
(396 x 396mm)
Horizontal (D2950A)
(362 x 394mm)
Back (X402-390)
(402 x 390mm)
Drawer Front (D2951A)
(374 x 192mm)
Left Side (D2947A)
(376 x 395mm)
Base (D2949A)
(396 x 396mm)
Right Side (D2948A)
(376 x 395mm)
Left Drawer Side (W370-124LH)
(370 x 124mm)
Right Drawer Side (W370-124RH)
(370 x 124mm)
45 6
7 8 9
10 11
Drawer Base (T321-367)
(321 x 367mm)
Drawer Back (W329-124)
(310 x 124mm)

Please check you have all the fittings listed below
Tools required
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A B C
D E F
G H I
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Nail (F51) x 11
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J
Electric drill
(do not use for
fitting screws)
L
Knock-in Peg (F171GY) x 4
N
L
Wedgefix (F639) x 2
13mm Screw (F63) x 613mm Screw (F52) x 6
MR Runner (F160) x 1
b
L Runner (F161) x 1
Mc
L Runner (F159) x 1
Ma
R Runner (F162) x 1
Md
350mm long
40mm Screw (F910) x 4
Metal dowel (F901) x 10 Large locking
nut (F900) x 8
Small locking
nut (F3) x 2
K
Handle (F894GRN) x 1
Foot (F233) x 4
32mm Screw (F72) x 1
38mm Screw (F81) x 8

6
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
A
B
A
C
C
Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on either surface of the drawer sides.
Make sure that the small groove is on the inside, as shown.
CC
78
A
A
Step 2
Prepare the drawer
front
Screw 2 metal dowels
into the drawer front .
Note: Tighten the metal
dowels up fully against
the panels.
A
6
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
C
7
8
Attach the drawer
sides to the drawer
fronts
Push the left drawer sides
. and right drawer sides
. onto the back of the
drawer fronts .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
7
8
6
C
C
7
8
6
7
8

6
Assembly Instructions
5
Step 4
J
J
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
10
7 8
6
9
7 8
10
9
9
J
Attach the handle
Attach the handle to
the drawer front
using screw .
Note: Do not
overtighten the screw.
K
I
6
7 8
Step 7
Fit the wedgefixes
Turn the drawer
assemby over and slide
2 wedgefixes into the
front and back grooves,
as shown, and tighten up
the screws.
L
J
J
L
L
L
10
7
8
9
7
8
10
I
K
6

Assembly Instructions
6
Step 8
Fit runners to the
drawer
Fit the runner to the
bottom edge of the left
drawer side , as
shown, making sure that
it is pushed up against
the back of the drawer
front . Use a bradawl
to mark the fixing
positions, then secure
with 2 screws .
Fit the runner to the
bottom edge of the right
drawer side using the
same method.
8
M c
7
6
H
M d
Runners must be
pushed up against
the drawer front
M c
H
H
H
H
M d
8
7
6
Step 9
Prepare the horizontal
Insert 4 large locking
nuts into the
horizontal .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Green
edge
B
B
B
B
B
B
5
5

Green edge
Assembly Instructions
7
Step 10
Step 11
A
Prepare the left side
Screw 2 metal dowels
into the left side .
Insert 2 large locking
nuts into the left side
. .
Fit the runner to the
left side .
The 1st screw uses
the 2nd hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
Fit a screw into the
2nd hole in at the top of
the runner .
A
B
B
Prepare the left side
a: Fit runner to the
left side .
The 1st screw uses
the 2nd hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the 2nd hole in at the top
of the runner .
c: Screw 4 metal
dowels into the left
side .
Insert 2 large locking
nuts into the left side
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Fit 2 hinge plates onto
the left side , making
sure that the slot is
facing towards the
finished front edge.
P a
1
H
H
M a
G
Finished front edge
G
1st
screw
2nd
screw
G
3rd
screw
M a
Finished front edge
H
G
P a
G
M a
G
G
H
A
1
B
1
M a
1
G
G
H
M a
1
B
B
A
A
M b
G
Finished front edge
G1st
screw
2nd
screw
G3rd
screw
M b
Finished front edge
H
G
G
M b
GH
Prepare the right side
Screw 2 metal dowels
into the right side .
Insert 2 large locking
nuts into the right
side . .
Fit the runner to the
right side .
The 1st screw uses
the 2nd hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
Fit a screw into the
2nd hole in at the top of
the runner .
A
2
B
2
M b
2
G
G
H
M b
2
Green edge

Green
edge
Green
edge Green
edge
Assembly Instructions
8
Step 12
Step 13
A
B
Fit the horizontal to
the right side
Push the horizontal
onto the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the horizontal .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
2
5
B
B
5
Fit the left side
Push the left side
onto the horizontal .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the horizontal .
Step 14
Prepare the top
Screw 4 metal dowels
into the top .
5
1
B
5
A
A
A
A
A
3
Green
edge
2
5
5
1
3

Green
edge
Assembly Instructions
9
Step 15
Step 16
Fit the top
Push the top onto
the assembly.
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the left side and right
side .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
B
3
2
1
A
B
B
3
1
2
Fit the base
Fit the base onto the
assembly using 4 screws
. .
4
E
E
E
E
E
Green
edge
4