Argos 346/4423 User manual

Gino Glass Round Table
Dimensions
Dia - 100cm
Height - 75.5cm
Issue 1 - 25/10/14
Important – Please read these instructions fully before starting assembly
Assembly Instructions - Please keep for future reference 346/4423
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
that all bolts and fittings are
tightend properly.
Handy Hints
• Keep these instruction for future
reference.
• Imported by:
Argos Ltd.
• If the glass is chipped or broken, stop using the product and
consult the Manufacturer or Supplier.
Glass Safty
489-499 Avebury Boulevard.
Saxon Gate West.
Central Milton Keynes.
MK9 2NW
• Batch No: 545019（按订单PO号）
• Date of Manufacture: Dec.2014（按订单出货年月）
• Type of glass used: 8mm toughened glass
Warning:
(a) Do not place very hot or very cold items on the glass surface(s) unless adequately thick table mats
are used to prevent such items from coming into contact with the glass.
(b) Do not sit or stand upon the glass surface(s).
(c) Do not use the glass as a chopping surface. Do not strike the glass with hard or pointed items.
(d) When cleaning glass panels use a damp cloth or leather with washing up liquid or soft soap if
necessary, do not use washing powders or any other substance containing abrasives since these
substances scratch glass.

Components - Panels
Please check you have all the panels listed below
2
1Post (dia6 x 65.5 cm) 2Connecting plate
(dia11 cm)
4Base
(dia60 x 8.6 cm )
3Bottom weight plate
(dia46 x 6.3 cm)
If you have damaged or missing components, call the
Customer Helpline: Argos = 0345 6400800
5Glass top
(dia100 cm )
Pre-assembled with partNote: 4

3
Please check you have all the fittings listed below
20mm Bolt x 3
A
Small plain washer x 3
D
25mm Bolt x 3
B
Large spring washer x 1
G
Wrench x 1
H
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
Large plain washer x 1
E
80mm Bolt x 1
C
Middle hex key x 1
J
Large hex key x1
K
Small spring washer x 3
F
Small hex key x 1
I
Components - Fittings
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
The bolts length is measured from the head to the point (25mm bolt sho wn
).

Assembly Instructions
Step 1
4
4
The bolt, nut, carboard,
foams fixing in between
bottom weight plate
and base are only
for packing purpose.
Package material should
be removed before
assembly.
3
4
3
Two people are needed
during assembly.
nut
carboard
bolt
foam
foam

Assembly Instructions
Step 2
Step 3
Assemble connecting
plate
Assemble base
5
Tightly secure the bolt
using large hex key .
Turn the base upright,
fix connecting plate
to post by using bolts .
A
C
G
E
A
A
1
2
3
4
2
Tightly secure the bolts
using small hex key .
K
I
Fix post , bottom
weight plate and base
4 by using bolt , large
spring washer and
large plain washer .
1
3
4C
G
E
A

Assembly Instructions
Step 4
Carfully position glass top
on connecting plate,
secure tightly by using
bolts , small spring
washers and small
plain washers .
Assembly is complete.
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
5
B
D
F
B
D
F
B
D
F
5
B
F
D
Assemble glass top
Remove the plastic film
on table top.
Tightly secure the bolts
using middle hex key .
J