Argos Camden 305/0741 User manual

MADE IN
BRITAIN
Dimensions
Width - 117cm
Depth - 49.5cm
Height - 183.5cm
Camden - 3 Door Robe
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 2 - 12/12/12
Important - Please read these instructions fully before starting assembly
Ruler - Use this ruler to help correctly identify the screws
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
305/0741
305/0758
ALR2832
Issue 2 - 12/12/12 - Changed the assembly method so that the Left Side is fitted after the Large Back Rail has been fitted.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 67kgs. Please lift
with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• Parts of the assembly will be
easier with 2 people.
Glue Safety - Take care when using glue, please follow the advice below
Skin contact: Remove contami-
nation by washing with soap and
water. This procedure should be
followed prior to aeting and
drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
1
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• From time to time check that
there are no loose screws on
this unit.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
1 2
80%
x2
90
x1
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
3
6
5
7
4
Hanging Rail (FHR343)
(343mm long)
8
Hanging Rail (FHR715)
(715mm long)
9
Upright (D2011A)
(1688 x 472mm)
Base (D2010A)
(1090 x 473mm)
Plinth (D2012A)
(1090 x 96mm) 10
11
Top (D2009a)
(1166 x 492mm)
Foldy Back (X733)
(1713 x 740mm)
Back (X734)
(1713 x 363mm)
Door (D2008A)
(1700 x 358mm) x 3
Left Side (D2004A)
(1800 x 491mm)
Right Side (D2005A)
(1800 x 491mm)
Large Back Rail (D2014A)
(725.5 x 130mm)
12
Small Back Rail (D2013A)
(349.5 x 130mm)
13

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Rule
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Tools required
Rule
ScissorsSquare
Spirit
level
Hammer Bradawl
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Step
ladder
Ruler - Use this ruler to help correctly identify the screws
40mm Screw (F910) x 2
B C
D E F
G H I
Nail (F51) x 38
M
LHinge plate
(F523) x 9
Rail Holder
(F891) x 4 13mm Screw (F63) x 26
Hollow core
locking nut
(F892) x 4
Small metal dowel
(F893) x 4
19mm Screw (F461) x 6
Metal dowel (F901) x 10
Large locking
nut (F900) x 12
Hinge (F522) x 9
A
Wooden dowel (F22) x 10
N
J K
13mm Screw (F79) x 13
O
Bracket (F327) x 1
Electric drill
(only use
when drilling
into walls)
P
Handle (F309) x 3
Double metal dowel (F566) x 1

A
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
Prepare the upright
a: Tap 2 wooden
dowels into the ends
of the upright .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
To fit the rail holder ,
screw through the top
hole with screw and
into the mark hole drilled
in the upright . Make
sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.
Turn upright panel over
E
F
F
b:
80%
x3 3
A
Finished
front edge
F
F
E
Turn the upright over
F
F
L
L
L
Finished
front edge
E
H
H
3
3
L
a:
H
10mm
A
A
3
L
b: Fit 3 hinge plates
onto the upright ,
making sure that the slot
is facing towards the
finished front edge.
To fit the rail holder ,
screw through the top
hole with screw and
into the mark hole drilled
in the upright . Make
sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.
Insert 2 large locking
nuts into the upright.
Note: Arrow on locking
nut must point towards
hole in edge of panel.
3
E
F
F
3
H
F
E
F
E

Assembly Instructions
5
Step 2
AH
H
A
H
H
C
C
C
C
C
Prepare the top
Screw 4 small metal
dowels into the holes
on the top .
Screw 2 metal
dowels into the holes
on the top .
Note: Tighten metal
dowels up fully against
the panels.
Step 3
Prepare the base
Insert 4 large locking
nuts into the base
Note: Arrow on locking
nut must point towards
hole in edge of panel.
Tap 2 wooden dowels
into the ends of the base
. .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
C
5
5
G
G
G
G
5
H
6
6.
A
6
Step 4
H
Prepare the small
back rail
Insert 2 large locking
nuts into the small
back rail .
Tap 2 wooden dowels
into the small back rail .
A
H
10mm
A
13
A
A
H
H
13
13

Finished
front edge
Assembly Instructions
6
Step 5
Fit base to right side
Push the base onto
the right side as
shown.
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the base .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
Step 4
5
2
5
F
F
H
B
3
5
Finished
front edge
Finished
front edge
K
K
K
6
3
Fit base to the upright
Push base onto the
upright and secure
using 2 screws .
Fit the top
Push the top onto
the upright .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the upright .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
5
3
H
H
3
Step 6
3
5
3
6

Assembly Instructions
Step 7
7
L
L
2
E
F
F
B
B
B
G
a: b:
B
B B
c:
Prepare the right side
a: Fit 3 hinge plates
onto the right side ,
making sure that the slot
is facing towards the
finished front edge.
b: To fit the rail holder
. , screw through the
top hole with screw
and into the mark hole
drilled in the right side
. . Make sure that it is
fitted straight, in line with
the panel edges and
then fit another screw
using the lower hole.
c: Push 2 hollow core
locking nuts into the
right side , making
sure that they are flush
against the panel’s
surface.
Using a hammer, tap in
the pin on the hollow
core locking nut .
Note: The pin should be
tapped in flush with the
top surface of the hollow
core locking nut .
d: Screw 4 metal
dowels into the holes
on the right side .
Note: Tighten metal
dowels up fully against
the panel.
2
2
2
F
E
F
E
F
F
B
B
L
L
L
2
Finished
front edge
G
G
G
G
d:
E
G

Assembly Instructions
8
Step 8Step 7
Fit the right side to
the assembly
Push the right side
onto the top .
Note: You will need to
make sure that the 2
small metal dowels
fitted to the top , slide
into the top of the 2
hollow core locking nuts
. fitted to the right
side .
Insert a
screwdriver
into the 2
hollow core
locking nuts
. and turn
the nuts
inside as far
as they will go.
2
6
C
B B
3
B
2
5
5
C
5
2
B
2
6G
H
5
13
Fit the small back rail
Push the small back rail
. onto the right side
and upright .
Use a screwdriver to
tighten the large locking
nut on the small back
rail .
Use a screwdriver to
tighten the 2 large
locking nuts on the
base .
2
13
3
H
13
Step 9
H
G
3
H
6

Assembly Instructions
Step 10
9
L
L
Prepare the left side
a: Fit 3 hinge plates
onto the left side ,
making sure that the slot
is facing towards the
finished front edge.
b: To fit the rail holder
. , screw through the
top hole with screw
and into the mark hole
drilled in the left side .
Make sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.
c: Push 2 hollow core
locking nuts into the
left side , making sure
that they are flush
against the panel’s
surface.
Using a hammer, tap in
the pin on the hollow
core locking nut .
Note: The pin should be
tapped in flush with the
top surface of the hollow
core locking nut .
d: Screw 4 metal
dowels into the holes
on the left side .
Note: Tighten metal
dowels up fully against
the panel.
1
E
F
F
B
B
B
G
a:
B
B B
c:
1
1
1
b: F
E
F
E
Finished
front edge
L
L
L
F
F
E
B
B
1
GG
G
G
d:
G