Argos Montana 395/6883 User manual

MADE IN
BRITAIN
Dimensions
Width - 90cm
Depth - 39.5cm
Height - 41cm
Montana - Corner TV Unit
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 2 - 08/05/15
Important - Please read these instructions fully before starting assembly
ALR3147
395/6883
391/7657
Issue 2 - 08/05/15 - The left side is now being fitted after the shelf has been fitted.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 17kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Components - Panels
Please check you have all the panels listed below
2
13
80%
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Left End (DF3541)
(353 x 216mm)
Top (DF3539)
(897 x 391mm)
Horizontal (DF3544)
(863 x 355mm)
2Right End (DF3542)
(353 x 216mm)
Back (DF3543)
(353 x 394mm)
Drawer Front (DF3545)
(889 x 215mm)
Left Drawer Side (W210-124LH)
(210 x 124mm)
Right Drawer Side (W210-124RH)
(210 x 124mm) Drawer Base (T841-207)
(841 X 207mm)
4
6
8
7
5Base (DF3540)
(897 x 391mm)
9
10
11
Drawer Back (W830-124)
(830 x 124mm)

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
A B
D E F
G H
M
I
K
Small locking
nut (F3) x 2
C
40mm Screw (F910) x 8
L
9mm Screw (F74) x 2
J
9mm Screw (F73) x 4
Knock-in Peg (F171GY) x 4
Large locking
nut (F900) x 10
Metal dowel (F901) x 12
Wedgefix (F639) x 4
19mm Screw (F461) x 1
38mm Screw (F81) x 8
Handle (F341) x 1
Drawer runner (F307) x 2
Foot
(F233) x 4
Tools required
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver

7
Prepare the drawer
front
Screw 2 metal dowels
into the drawer front .
Note: Tighten the metal
dowels up fully against
the panels.
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
A
A
C
CC
C
89
Step 2
A
7
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
C
8
9
Attach the drawer
sides to the drawer
front
Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
8
9
7
C
C
8
9
9
A
7
A
8

7
Assembly Instructions
5
Step 4
D
D
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
11
8 9
7
10
8 9
11
10
10
D
Attach the handle
Attach a handle to the
drawer front using
screw .
L
G
7
8 9
Step 7
Fit the wedgefixes
Turn the drawer
assembly over and slide
4 wedgefixes into the
front and back grooves,
as shown, and tighten up
the screws.
K
D
D
K
K
K
K
K
11
8
10
8
9
11
G
9
L
7

Finished
front edge
Finished
front edge
Finished
front edge
Assembly Instructions
6
Step 8
Prepare the left side
a: Place a runner
onto the left side .
Slide back the top of
runner and use the 2nd
hole from the front to fit
the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the left side .
c: Screw 2 metal
dowels into the left
side .
Insert 2 large locking
nuts into the left side
. .
Note: The arrow on the
locking nuts must point
towards the hole in the
edge of the panel.
J
1
H
J
H
front edge
H
J
back edge
H
J
b:
a:
c:
A
1
1
1
1
B
1
H
A
B
B
A
B
1
H
J

B
B
Assembly Instructions
7
Step 9
Prepare the right side
a: Place a runner
onto the right side .
Slide back the top of
runner and use the 2nd
hole from the front to fit
the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the right side .
c: Screw 2 metal
dowels into the right
side .
Insert 2 large locking
nuts into the right
side .
Note: The arrow on the
locking nuts must point
towards the hole in the
edge of the panel.
J
2
H
J
H
b:
a:
c:
A
2
2
B
2
Front edge
H
J
Back edge
H
J
H
J
Finished
front edge
Finished
front edge
2
2
Finished
front edge
2
H
A
A

Finished
front edge
Assembly Instructions
8
Step 10
Prepare the top
Screw 6 metal dowels
into the top .
A
A
A
A
A
A
A
4
Step 11
Fit the right side to
the top
Push the right side
onto the top .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the right side .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
Step 12
2
4
B
B
2
4
4
2
Prepare the horizontal
Insert 4 large locking
nuts into the
horizontal . B
B
6
B
B
B
6
B
A

Assembly Instructions
9
Step 13
Fit the horizontal
Push the horizontal
onto the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the horizontal .
2
6
B
6
2
6
1
2
6
B
B
Step 15
Prepare the back
Insert 2 large locking
nuts into the back .
Step 14
B33
Fit the left side to the
top and horizontal
Push the left side
onto the top and
horizontal .
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the top and the
horizontal .
1
4
6
B
6
4
4