Argos 266/0709 User manual

MADE IN
BRITAIN
Dimensions
Width - 152cm
Depth - 49cm
Height - 181cm
Capella - 2 Drawer 4 Door Robe
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 6 - 23/04/14
Important - Please read these instructions fully before starting assembly
266/0709
266/9683
241/5844
248/4112
ALR3000
04/08/11 - Drawer Front size amended to 743 x 157mm.
Drawer assembly changed to Knock-in Pegs.
Drawer Sides and Drawer Back changed to take Knock-in Pegs.
24/02/12 - Drawer Support added and drillings have been updated for the Base and Fixed Shelf.
Base and Fixed Shelf have both gone up to issue B.
Issue 4 - 16/05/12 - New Argos code added
Issue 5 - 01/04/2014 - Drawer box size increased.
Add 8 Drawer wedges.
Add 5 plastinails.
Remove old cat codes and add new ones.
Issue 6 - 23/04/14 - The flange head screws for the backs have been replaced with 6 Nail Screws and Back Holders.
The Base and Fixed Shelf are now issue C because the Drawer Support has been moved back because of the deeper drawers.
Amended the drawer assembly drawings to represent the new drawer wrap changes.
The step for adding the plastinails is now a separate step.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 96kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.
Tools required
Rule
Scissors
Spirit
level
Hammer Bradawl
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Step
ladder
Electric drill
(only use
when drilling
into walls)
Square
mm 10 20 30 40 50 60 70 80 90 100 mm 10 20 30 40 50 60 70 80 90 100

Components - Panels
Please check you have all the panels listed below
2
1
80% x 3
90% x 1
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Left Side (D1013A)
(1808 x 490mm)
2 3
7
Right Side (D1014A)
(1808 x 490mm)
11
8
12
Large Door (D1017A)
(1701 x 369mm) x 2
9
4
6
10
15
13 14
17 Large Back (X830A)
(1711 x 753mm) x 2
Hanging Rail (FHR728)
(728mm long) x 2
16
Mirror Door (D1030A)
(1381 x 369mm) x 2
(Mirror - SG14
1376 x 311mm
4mm Safety Back SAR)
Short Divider
(D1027A)
(323 x 470mm) x 2
Centre Divider (D1028A)
(1369 x 470mm)
Plinth (D1032A)
(1491 x 85mm)
Top (D1026A)
(1491 x 471mm)
5
Drawer Front (D1031A)
(743 x 157mm) x 2
Drawer Back
(W688-124BK)
(688 x 124mm) x 2
Drawer Base (T699-367)
(699 x 367mm) x 2
Fixed Shelf (D1029C)
(720 x 470mm)
Drawer Support
(D1397A)
(302 x 302mm)
18
Left Drawer Side
(W370-124LH)
(370 x 124mm) x 2
Right Drawer Side
(W370-124RH)
(370 x 124mm) x 2
Base (D1111C)
(1491 x 471mm)

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 10
B
Metal dowel (F901) x 16
C
D E
Large locking
nut (F900) x 12
F
G H I
Nail (F51) x 48
see malibu fitment mk2 for large number of panels and fittings
N
Rail holder
(F1014) x 4
25mm Screw (F50) x 12 13mm Screw (F79) x 1
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
J
13mm Screw (F63) x 24
Drawer runner (F1004) x 4
K
9mm Screw (F74) x 4
M
P
Handle (F930) x 6
T
Small locking
nut (F3) x 4
Bracket (F327) x 1
O
R
Hinge (F522) x 6
S
Hinge plate
(F523) x 6
40mm Screw (F910) x 14
Q
Hinge Plate
(F521) x 6 Hinge (F520) x 6
L
9mm Screw (F73) x 8
R
AHP1546
AHP0826
Knock-in Peg (F171GY) x 8
V
Plastic Nail
(F91) x 5
Wedgefix
(F639) x 8
UWX
Nail screw
(F277) x 6
Back holder (F276) x 6
*These can also be round

9
Assembly Instructions If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
x 2
Prepare the drawer
fronts
Screw 2 metal dowels
into the holes shown on
the back of each drawer
front .
Note: Tighten the metal
dowels up fully against
the panels.
B
9
B
Step 3
B
B
9
80%
x 2
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
E
12
13
Step 2Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.
E
x 2
EE
12 13
x 2
x 2
B
E
Attach the drawer
sides to the drawer
fronts
Push the left drawer sides
. and right drawer sides
. onto the back of the
drawer fronts .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
12
13
9
E
E
12
13
Note: The locking nuts can be on either surface of the drawer sides.
Make sure that the small groove is on the inside, as shown.
13
12

F
F
9
Assembly Instructions
5
80%
x 2
Attach the handle
Attach a handle to
each drawer front
using 2 screws .
M
H
Step 6
9
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front . .
Step 5
Fit the drawer back
Fit the drawer back .
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
15
12 13
9
14
12 13
15
14
14
F
x 2
x 2
12 13
Fit the wedgefixes
Turn the 2 drawer
assemblies over and
slide 4 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
U
Step 7
Step 4
F
F
U
15
12
13
14
12
13
15
x 2
x 2
H
H
M
U
U
U
U
9

Finished
top edge
Finished
top edge
Finished
top edge
Finished
front edge
Finished
top edge
Assembly Instructions
6
Step 8
80%
x 3
Finished
front edge
Finished
front edge
L
P
Prepare a short
divider
a: Place 2 runners on
a short divider . Slide
back top of runner and
use 1st hole from the
front to fit 1st screw .
b: Slide runner back the
other way and use 3rd
hole from the back to fit
2nd screw .
P
7
L
L
Prepare the other
short divider
a: Place 2 runners on
a short divider . Slide
back top of runner and
use 1st hole from the
front to fit 1st screw .
b: Slide runner back the
other way and use 3rd
hole from the back to fit
2nd screw .
P
7
L
L
a: L
P
L
P
Back edge
L
P
b:
a:
b:
L
PL
P
Finished
front edge
L
P
Finished
front edge
L
L
Back edge
L
P
Finished
front edge
Step 9
7
7
7
7
L
L

Assembly Instructions
7
Step 10
Step 11
80%
x 3
Prepare the fixed
shelf
Screw 2 metal dowels
into the fixed shelf .
B
B
8
Finished
front edge
B
8
G
G
Finished
front edge
Finished
front edge
Finished
front edge
8
Join the short dividers
to the fixed shelf
Attach the 2 short
dividers to the fixed
shelf using 4 screws
. .
7
8
G
7
G
G
7

Assembly Instructions
Step 12
Step 13
8
Finished
front edge
Q
Prepare the centre
divider
Important: The hinge
plates used in this
step are in the bag
marked as AHP0826.
Fit 3 hinge plates to
the centre divider as
shown, making sure that
the slot is facing towards
the finished front edge.
Push a rail holder into
the centre divider .
Make sure that it is fitted
straight, in line with the
panel edges.
Turn the centre divider
over
Fit 3 hinge plates to
the other surface of the
centre divider as
shown, making sure that
the slot is facing towards
the finished front edge.
Push another rail holder
. into the centre divider
. .
Q
Q
Q
Q
Q
Q
QFinished
front edge
Q
Q
3
3
3
3
Q
3
Turn the centre
divider over
AHP1546 AHP0826
N
N
N
3
N
Finished
front edge
8
3
Fit the centre divider
Attach the centre divider
. to the fixed shelf
using 2 screws . G
G
3 8
G

A
A
b:
Assembly Instructions
9
Step 14
Step 12
Step 15
Prepare the drawer
support
Insert 2 large locking
nuts into the
drawer support .
D
D
18
Note: Due to the manufacturing process,
the drawer support may either have 1 or
2 plain chipboard surfaces.
D
18
A
A
D
A
A
Finished
front edge
D
D
D
Prepare the top and
base
a: Tap 4 wooden dowels
. into the top .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 4 large locking
nuts into the top .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
b: Tap 4 wooden
dowels into the base
. .
Insert 4 large locking
nuts into the base
A
4
4
5
D
4
D
A
A
Finished
front edge
D
D
D
5
plain chipboard surface
a:
A
5
D.
D
Plain
chipboard
surface