Aries 2055123 User manual

PAGE 1 • 2055123-INS-RB • 800.798.0813 • NEED ASSISTANCE? • ARIESAUTOMOTIVE.COM
Level of Difficulty
Easy
Scan
for helpful
install tips
INSTALLATION MANUAL 2055123
Parts List
1Driver / left
side bar / running board
1Passenger / right
side bar / running board
4VersaTrac™mounting bracket,
universal
8 Hex bolt, M8 (B)
8Flat washer, M8 (B)
8Lock washer, M8 (B)
8Hex nut, M8 (B)
8Clip nut M10
16 Hex bolt, M10 (S)
24 Flat washer, M10 (S)
16 Lock washer, M10 (S)
8Hex nut, M10 (S)
(S) = Silver hardware
(B) = Black hardware
Tools Required
Ratchet Socket, 13mm
Torque wrench Socket, 16mm
Level
Product Image
AdvantEDGE™
RidgeStep™

ARIESAUTOMOTIVE.COM • NEED ASSISTANCE? • 800.798.0813 • 2055123-INS-RB • PAGE 2
Step 1
Starting on the driver side, locate
the five mounting tabs along
the bottom edge of the vehicle.
This installation will use the
first and fifth mounting tabs.
Step 2
Starting at the front driver-side mounting
location, insert an M10 clip nut into the
square hole and align it over the adjacent
round hole.
Place a bracket onto the vehicle
and secure with an M10 hex bolt,
lock washer and flat washer.
Snug the hardware,
but do not fully tighten.
Step 3
Finish securing the front mounting
bracket to the vehicle using an M10
hex bolt and flat washer from the outside
of the bracket and an M10 hex nut, lock
washer and flat washer on the inside.
Repeat this step for the remaining
bottom bolt location.
Notes and Maintenance
Before you begin installation, read all instructions thoroughly.
Proper tools will improve the quality of installation and reduce the time required.
For chrome powder coat, polish may be used to clear small scratches
and scuffs on the finish. Mild soap may be used also to clean the product.
For black finishes, mild soap may be used to clean the product.
Refer to the table to the left when securing hardware during the
installation process to help prevent damage to the product or vehicle.
Torque Specifications
METRIC
M6 bolt 3 ft.-lbs.
M8 bolt 7 ft.-lbs.
M10 bolt 16 ft.-lbs.
M12 bolt 28 ft.-lbs.
SAE
1/4" bolt 3 ft.-lbs.
5/16" bolt 7 ft.-lbs.
3/8" bolt 16 ft.-lbs.
7/16" bolt 20 ft.-lbs.
1/2" bolt 28 ft.-lbs.

PAGE 3 • 2055123-INS-RB • 800.798.0813 • NEED ASSISTANCE? • ARIESAUTOMOTIVE.COM
Step 4
Repeat steps 2 and 3 to install the rear
bracket over the mounting tab location
from step 1.
Step 5A - AdvantEDGE™Side Bars
Carefully place the side bar
onto the mounting brackets.
Ensure the outer edge of the side bar
is lined up with the outer edge of
the mounting brackets.
Step 5B - AdvantEDGE™Side Bars
Locate the round slots on
the base of the side bar.
Insert two M8 hex bolts into each
slot, sliding them towards the front
mounting bracket.
Step 5C - AdvantEDGE™Side Bars
Slide the bolts down the rail so that two
bolts are positioned for each bracket.
Carefully lift the side bar up and move
the bolts as necessary so they are in line
with the slots on the mounting brackets.
Secure the side bar to the brackets
using flat washers, lock washers
and M8 hex nuts.
Snug the hardware, but do not fully
tighten. Continue to step 7.
If installing RidgeStep™running boards, skip to Step 6A

ARIESAUTOMOTIVE.COM • NEED ASSISTANCE? • 800.798.0813 • 2055123-INS-RB • PAGE 4
Step 7
At this time, adjust the side bar /
running board to the desired location.
With the side bar / running board
in position, it is recommended to
tighten all brackets to the vehicle first,
followed by the side bar / running board
connections.
For recommended torque specifications,
refer to the table on page two.
Step 8
Repeat steps 1 through 7 on
the passenger side of the vehicle.
Congratulations on the installation
of your new ARIES AdvantEDGE™
side bars / RidgeStep™running boards.
With the side bars / running boards
installed, periodic inspections should
be performed to ensure all mounting
hardware remains tight.
To protect your investment, see the
'Notes and Maintenance' section on the
second page of this instruction manual.
Step 6A - RidgeStep
™Running Boards
Slide the two C-shaped track
mounting brackets into the rail slots.
Step 6B - RidgeStep
™Running Boards
Carefully place the running board
onto the mounting brackets.
Align the C-shaped track mounting
brackets with the mounting brackets
on the vehicle.
Attach the C-shaped track mounting
brackets to the mounting brackets using
M8 hex bolts, lock washers and flat
washers.