ARTHUR HOLM AH17S HDGA User manual

User manual
AH17S HDGA
17’’ professional widescreen monitor with manually tilt adjustment

Table of contents
EC REGULATIONS & SECURITY 6
SAFETY INSTRUCTIONS 7
FEATURES 8
BOX CONTENTS 8
CONTROLS 9
OSD MENU 10
INPUT CONNECTORS 13
INPUT SIGNALS 13
PRODUCT WARRANTY 15

Welcome
Thank you for purchasing an ARTHUR HOLM product.
Our product range has been designed to create the perfect meeting room,
where the screens are a part of the interior design as well as essential
communication tools.
Please, read this installation and operating instructions carefully and keep
them in a safe place for a future consultation.
We remain at your entire disposal if you have any suggestions
that would help us to improve our products.
Henrik Holm
General Manager

6
EC Regulations and Security
ATTENTION: Do not disassemble or modify the device in any way.
This symbol warns of the presence of dangerous un-insulated voltages
inside some of the components, of sufficient magnitude to expose people
to risk of electronic shock.
This symbol draws attention to important use and maintenance instructions
in the manual that accompanies the unit.
This symbol indicates that the equipment conforms to the norms
established by the European Community.

7
Safety instructions
PLUGS
– Do not dismantle any part of the monitor power connector.
– Disconnect the power plug from the AC outlet when the monitor is not
going to be used for an indefinite period of time.
POWER AND EXTENSIONS CORDS
– Use the appropriate power cord with the correct plug type
– Do not overload wall outlets or power cords
– Make sure the total ampere passed through a extension cord does not
exceed the maximum allowed by the cable used
– Do not place anything on the power cord
– Do not locate this product where a person may walk or trip over the cord
Wiring connected to hazardous voltage requires installation by qualified
personnel or the use of ready-made flexible cables.
For your security, your equipment must be connected to an electrical
outlet with grounding connection protection.
The operating electrical outlet must be in an easily accessed place.
ENVIRONMENT
– Install the equipment on an elevated, flat surface
– Install the equipment in a ventilated area
– Avoid exposing the equipment to:
Rain or water
Excessive heat, cold or humidity
Areas exposed to direct sunlight
Dirty areas
Equipment generating strong magnetic fields
– Avoid placing open containers of liquid, near the equipment
– Keep a minimum distance of 30mm in order to have good ventilation
– Never place any sources of flames, such as lighted candles, etc. above the device
– If you are using the device in extreme weather conditions and/or tropical
climates, the equipment should be installed in a room which ensures a
reasonable level of temperature and humidity
- To prevent damage the equipment must be firmly anchored to the surface,
as shown in the installation instructions

8
System Description
FEATURES
- 17" TFT Active Matrix display, widescreen format, FULL HD
- Low power consumption
- Low radiation
- Quick response time
- Signal input: HDMI HDCP compliant
- Manually tilt adjust from 0º to 25º
- Monitor housing made of solid mechanized aluminium in anodized finish and
front glass
BOX CONTENTS
Before the installation of your monitor, please check the contents of the
shipping box, it must contain the following items:
- Monitor unit
- Power cord
- Power supply 100-240Vac, 50-60Hz. Output 12V
- User Manual

9
Controls
REMOTE CONTROL
Use the IR remote control to access the monitor configuration:
POWER Switch ON/OFF the monitor
MENU Activates the OSD menu on screen
DOWN Cursor control down on OSD menu. When the
OSD menu
is not active on screen, selects the input
source
UP Cursor control up on OSD menu
LEFT Cursor control left on OSD menu
RIGHT Cursor control right on OSD menu
OK Selects the function on OSD menu
ACCESSING THE MENU SYSTEM
– With the OSD off, push the MENU button to activate the main OSD menu
– Press the UP and DOWN button to move from one function to another.
As you move from one icon to another, the function name changes
to reflect the function or group of functions represented by that icon.
Please refer to the following sections below to view a complete list of
all the functions available for the monitor
– Press the OK button to enable the item
– When a function is selected, press the LEFT and RIGHT buttons in order to
change the parameter of the function

10
OSD menu
Press the Menu button to access to the main menu:
PICTURE
CSM Configuration of the image colour
Cool
Normal
Warm
User (manually adjustment of red, green and blue colours)
PSM Configuration of the bright image
Dynamic
Standard
Mild
Game
User (manually adjustment of brightness and contrast)
Contrast Image contrast adjustment
Brightness Image brightness adjustment

11
OSD menu
SCREEN
Input Input signal selection
HDMI
ARC Aspect image on screen
Full The image is showed on full
screen
16:9 Shows the image on screen with
16:9 aspect
Aspect Shows the image on full screen
but keeps the original aspect
ratio of the input image
4:3 Shows the image on screen
with 4:3 aspect
1:1 Shows the image on screen with the
original resolution
Backlight Adjust the backlight of the screen
Flip Flip the image on screen
Off: Image with no flip
1 Vertical flip
2 Horizontal flip
3 Rotate
OSD-Flip Flip the menu on screen (OSD)
Off Image with no flip
1 Vertical flip
2 Horizontal flip
3 Rotate

12
OSD menu
SETUP
Language OSD language selection
PC Control Adjust the image on screen. Only on ARGB (analogue) input
(Not available on this model)
H-Pos Adjust the image on screen horizontally
V-Pos Adjust the image on screen vertically
Phase Adjust the phase
Clock Adjust the clock
Auto Adjust Auto adjust the image on screen
Reset PC image control reset
1050 Selection of the exact input resolution. Only for ARGB
(analogue) input. (Not available on this model)
1400 x 1050
1680 x 1050
WXGA Selection of the exact input resolution. Only for ARGB
(analogue) input. (Not available on this model)
1024 x 768
1280 x 768
1360 x 768
BG Color Background colour of the screen when there is no input
signal. The monitor only goes to stand by mode when black
colour is selected
BLACK
RED
GREEN
BLUE

13
Input Connectors
The monitor has two cables:
Power Cable Power input 12Vdc. Connect the power supply delivered
with the unit
Signal Cable HDMI female cable. Connect the input signal
Input Signals
RESOLUTION Horizontal freq (KHz) Vertical freq (Hz) Scanning type
800x600@60Hz 37.879 60.317 Progressive
800x600@72Hz 48.077 72.188 Progressive
800x600@75Hz 46.875 75.000 Progressive
1024x768@60Hz 48.363 60.005 Progressive
1024x768@70Hz 56.476 70.070 Progressive
1024x768@75Hz 60.023 75.030 Progressive
1360x768@60Hz 47.72 59.799 Progressive
1280x1024@60Hz 63.981 60.020 Progressive
1600x1200@60Hz 75.000 60.00 Progressive
1680x1050@60Hz 64.742 59.946 Progressive
1920x1080@60Hz 66.647 59.98 Progressive

14
Information on Disposal for users of waste Electrical & Electronic
equipment
This symbol on the products and/or accompanying documents means
that used electrical and electronic products should not be mixed with
general household waste.
For proper treatment, recovery and recycling, please take these products
to designated collection points, where they will be accepted on a free of
charge basis. Alternatively, in some countries you may be able to return
your products to your local retailer upon the purchase of an equivalent
new product.
Disposing of this product correctly will help to save valuable resources
and prevent any potential negative effects on human health and the
environment which could otherwise arise from inappropriate waste
handling. Please contact your local authority for further details of your
nearest designated collection point.
Penalties may be applicable for incorrect disposal of this waste, in
accordance with national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact
your dealer or supplier for further information.
Information on disposal in countries outside the European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local authorities or
dealer and ask for the correct method of disposal.

15
Product Warranty
Albiral Display Solutions S.L WARRANTY - Valid from January 2016
This warranty covers the original product purchase for a period of 24 months from the
date of purchase.
GENERAL WARRANTY TERMS
A) Parts. During the above mentioned warranty period, the replacement of any electronic
and mechanical parts against any defects in manufacturing. The warranty does not cover
any faulty electronic and/or mechanical components arising from incorrect installation,
unauthorized modification, and inadequate transport or as a result of atmospheric
phenomenon.
B) Labour. Albiral Display Solutions S.L. covers labour costs for replacement of any
defective parts (in accordance to paragraph A) during the period of this warranty.
C) Transport costs.
I) In the case that a manufacturing defect occurs within 30 days after the purchase
date, both freight and insurance will be paid by Albiral Display Solutions, S.L.
Albiral Display Solutions S.L. will not be responsible for the damages caused by
transportation if the customer does not inform in writing when receiving the goods.
II) After 180 days of the purchase date, both freight and insurance costs will be paid
by the customer.
D) Albiral Display Solutions S.L. will not be responsible for the damages caused by
transportation, when this one is paid by the customer.
E) The warranty is not valid if personnel other than the Authorised Service Centre have
handled the product, if the product has been manipulated or warranty seals have been
removed or manipulated.
F) The beneficiary of the warranty will have to return the product in its original packaging
or in an appropriate package that will warrant no damages during transportation.
G) The warranty is not valid if the customer does not include a RMA form and a copy of
the purchasing invoice.
Albiral Display Solutions S.L. recognizes all guaranteed user rights by all legal rules from
its region, and in the absence of them, all established consumer rights by general law
26/84.
Albiral Display Solutions S.L.

Patents
ES 1051718UU
ES 1061088UU
EP 1574150A1
ES 1068395 U
WO 2009141744
MU 170180 ES00
EP 2289367 A1
MU 17301 ES00
MU 17322 ES00
MU 17376 ES00
MU 17403 ES00
Fàtima 25, Sant Hipòlit de Voltregà
08512 Barcelona – Spain
tel: [phone] / 23 83
fax: [phone] / 23 72
web: www.arthurholm.com
e-mail: [e-mail]
This manual can be modified without previous notice. ENG - January 2016