ASRock Industrial IMB-1005 User manual

IMB-1005
User Manual
Version 1.0
Published July 24, 2023
Copyright©2023 ASRockInd INC. All rights reserved.

Version 1.0
Published July, 2023
Copyright©2023 ASRockInd INC. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRockInd Inc.
Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identication or explanation and to the owners’ benet, without intent to
infringe.
Disclaimer:
Specifications and information contained in this documentation are furnished
for informational use only and subject to change without notice, and should
not be constructed as a commitment by ASRockInd. ASRockInd assumes no
responsibility for any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRockInd does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or tness for a particular
purpose.
In no event shall ASRockInd, its directors, ocers, employees, or agents be liable
for any indirect, special, incidental, or consequential damages (including damages
for loss of prots, loss of business, loss of data, interruption of business and the
like), even if ASRockInd has been advised of the possibility of such damages arising
from any defect or error in the documentation or product.
is device complies with Part 15 of the FCC Rules. Operation is subject to the fol-
lowing two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
e terms HDMI®and HDMI High-Denition Multimedia Interface, and the HDMI
logo are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.

WARNING
THIS PRODUCT CONTAINS A BUTTON BATTERY
If swallowed, a button battery can cause serious injury or death.
Please keep batteries out of sight or reach of children.
CALIFORNIA, USA ONLY
The Lithium battery adopted on this motherboard contains Perchlorate, a toxic
substance controlled in Perchlorate Best Management Practices (BMP) regulations
passed by the California Legislature. When you discard the Lithium battery in
California, USA, please follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardous-
waste/perchlorate”
AUSTRALIA ONLY
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and
compensation for any other reasonably foreseeable loss or damage caused by our
goods. You are also entitled to have the goods repaired or replaced if the goods fail
to be of acceptable quality and the failure does not amount to a major failure. If you
require assistance please call ASRockInd Tel : [phone] ext.123 (Standard
International call charges apply)
ASRockInd INC. hereby declares that this device is in compliance with the essen-
tial requirements and other relevant provisions of related UKCA Directives. Full
text of UKCA declaration of conformity is available at: http://www.asrockind.com
ASRockInd INC. hereby declares that this device is in compliance with the essen-
tial requirements and other relevant provisions of related Directives. Full text of
EU declaration of conformity is available at: http://www.asrockind.com
ASRockInd follows the green design concept to design and manufacture our prod-
ucts, and makes sure that each stage of the product life cycle of ASRockInd product
is in line with global environmental regulations. In addition, ASRockInd disclose
the relevant information based on regulation requirements.
Please refer to https://www.asrockind.com/general/about.asp?cat=Responsibility
for information disclosure based on regulation requirements ASRockInd is com-
plied with.
DO NOT throw the motherboard in municipal waste. is product has
been designed to enable proper reuse of parts and recycling. is sym-
bol of the crossed out wheeled bin indicates that the product (electrical
and electronic equipment) should not be placed in municipal waste.
Check local regulations for disposal of electronic products.

Contents
Chapter 1 Introduction 1
1.1 Package Contents 1
1.2 Specications 2
1.3 Motherboard Layout 4
1.4 I/O Panel 8
1.5 Block Diagram 9
Chapter 2 Installation 10
2.1 Screw Holes 10
2.2 Pre-installation Precautions 10
2.3 Installation of Memory Modules 11
2.4 Expansion Slots 12
2.5 Jumpers Setup 13
2.6 Onboard Headers and Connectors 17
Chapter 3 UEFI SETUP UTILITY 24
3.1 Introduction 24
3.1.1 Entering BIOS Setup 24
3.1.2 UEFI Menu Bar 25
3.1.3 Navigation Keys 26
3.2 Main Screen 27
3.3 Advanced Screen 28
3.3.1 CPU Conguration 29
3.3.2 Chipset Conguration 32
3.3.3 Storage Conguration 34

3.3.4 Super IO Conguration 36
3.3.5 ACPI Conguration 38
3.3.6 USB Conguration 39
3.3.7 Trusted Computing 40
3.4 Hardware Health Event Monitoring Screen 42
3.5 Security Screen 43
3.6 Boot Screen 44
3.7 Exit Screen 45

1
IMB-1005
Chapter 1 Introduction
Thank you for purchasing ASRockInd IMB-1005 motherboard, a reliable mother-
board produced under ASRockInd’s consistently stringent quality control. It delivers
excellent performance with robust design conforming to ASRockInd’s commitment to
quality and endurance.
In this manual, chapter 1 and 2 contain introduction of the motherboard and step-by-
step guide to the hardware installation. Chapter 3 contains the conguration guide to
BIOS setup.
Because the motherboard specications and the BIOS soware might be updated, the
content of this manual will be subject to change without notice. In case any modica-
tions of this manual occur, the updated version will be available on ASRockInd website
without further notice. You may nd the latest CPU support lists on ASRockInd web-
site as well.
ASRockInd website https://www.asrockind.com/
If you require technical support related to this motherboard, please visit our website for
specic information about the model you are using.
https://www.asrockind.com/support/index.asp
1.1 Package Contents
ASRockInd IMB-1005 Motherboard (Mini-ITX (6.7-in x 6.7-in x 1.6-in, 17.0 cm x
17.0 cm x 4.1 cm)

2
1.2 Specications
Form Factor Dimensions Mini-ITX (6.7-in x 6.7-in x 1.6-in, 17.0 cm x 17.0 cm x 4.1
cm
Processor
System
CPU
Intel® Alder Lake-N SoC Processors
IMB-1005J (N97, QC, Max Speed Up to 3.6GHz, 12W)
*For other CPU SKUs request, please contact regional Sales
for availability
Chipset SoC
BIOS AMI SPI 256 Mbit
Memory
Technology Single Channel DDR4 3200 MHz
Capacity 16GB
Socket 1 x 260-pin SO-DIMM
Graphics
Controller Intel® UHD Graphics
HDMI HDMI 2.0b
Max resolution up to 4096 x 2160@60Hz
VGA Max resolution up to 1920 x 1200@60Hz
LVDS Dual channel 24 bit up to 1920 x 1200@60Hz
(connector shared with eDP)
eDP Max resolution up to 1920 x 1080@60Hz
(connector shared with LVDS)
Multi Display Triple display
Expansion
Slot
PCIe 1 x PCIex1 (Gen3)
M.2
1 x M.2 (Key E, 2230) with PCIe x1, USB 2.0 and CNVi for
Wireless
1 x M.2 (Key B, 3042/3052) with PCIe x1, USB 3.2 Gen1,
USB 2.0 and SIM for 4G/5G
SIM Socket 1 x SIM socket connected to M.2 key B
Audio Interface Interface Realtek ALC662/ALC897 HD, High Denition
Audio. Mic-in, Line-out
Ethernet
Controller/
Speed
LAN1: Realtek RTL8125BG with 10/100/1000/2500 Mbps
LAN2: Realtek RTL8125BG with 10/100/1000/2500 Mbps
Controller 2 x RJ-45
Rear I/O
HDMI 2 x HDMI2.0b
VGA 1
Ethernet 2 x 2.5 Gigabit LAN
USB 2 x USB 3.2 Gen1
2 x USB 2.0
Audio 2 (Mic-In, Line-Out)
COM COM1, COM2, COM3 (RS-232/422/485)

3
IMB-1005
Internal
Connector
USB
2 x USB 3.2 Gen1 (1 x USB 3.2 header)
3 x USB 2.0 (1 x 2.54 pitch header, 1 x USB 2.0 Type-A
vertical connector)
COM
COM4 (RS-232)
COM5 (RS-232 or TTL (optional))
COM6 (RS-232 or ccTalk (optional))
GPIO 4 x GPI, 4 x GPO
TPM TPM Header
LVDS 1 (connector with LVDS/eDP signal, switch by BIOS)
SATA PWR
Output 1
Speaker Header 1
MIPI Camera
Header 1 (optional)
Storage M.2 1 x M.2 (Key M, 2242/2260/2280) with PCIe Gen3 x1
or SATA3 for SSD
SATA 1 x SATA3 (6Gb/s)
Watchdog
Timer
Output From Super I/O to drag RESETCON#
Interval 256 Segments, 0, 1, 2, ...255 Sec
Power
Requirements
Input PWR ATX-PWR (24+4-pin) and 12~28V DC-In co-design
Power On
AT/ATX Supported
-AT: Directly PWR on as power input ready
-ATX: Press button to PWR on aer power input ready
Environment
Operating
Temp -20ºC - 70ºC
Storage Temp -40ºC - 85ºC
Operating
Humidity 5% - 90%
Storage
Humidity 5% - 90%

4
1.3 Motherboard Layout
20
IMB-1005
Industrial
CPU_FAN1
PCIE1
SPEAKER1
BLT_VOL1
PNL_PWR1
TPM1
1
1
JGPIO1
M2_B1
SATA_PWR1
1
SMBUS_TEST1
PWR_COM4
PWR_COM5
PWR_COM6
BIOS
ROM
LVDS1
ATX12V1
COM2
COM1
VGA1 COM3
Top:
LAN1
USB 3.2 Gen1
T: USB3H1_2
B: USB3H1_1
Top:
LAN2
USB 2.0
T: USB2_4
B: USB2_3
Top:
LINE O UT
Bottom:
MIC IN
1
PWR_COM1 PWR_COM2
BLT_PWR1
DACC1
DDR4_A1 (Support DDR4 Only)
HDMI2
HDMI1
M2_M1
M2_E1
SIM1
PWR_COM3
COM4 COM5 COM6
BUZZ2
1
BKT_PWR1JGPIO_PWR1
13 24
11
56
10
14
12
13
16
17
18
21
19
222324
25
30313234
37
36
35
33 27
29 28 26
78
9
15
1
1
1
1
CC_TALK_OUT1
SATA30_
1
11 1
1
USB2_7
1
ATXPWR1
1
1
1
USB3H134__
PANEL1
1
1
SPDIF1
BAT1
1
1
HD_AUDIO1
1
1
111
USB2_5_6
1
1
1
1
1
CI1CI2
JGPIO_SET1CLRMOS1 CLRMOS2
BLT_PWM1 BLT_PWM2
SIO_AT1
1
11
1111 111
11
PLED PWRBTN
HDLED RESET
Top :

5
IMB-1005
1
MIPI1
ESPI1
1
38
39
Back:

6
1 : COM Port PWR Setting Jumpers
PWR_COM1 (For COM Port1)
PWR_COM2 (For COM Port2)
PWR_COM3 (For COM Port3)
2 : 4-pin Power Connector (ATX12V1)
3 : 24-pin ATX Power Input Connector (ATXPWR1)
4 : USB 2.0 Port (USB2_7)
5 : SMBUS_TEST1
6 : 4-Pin CPU FAN Connector (+12V) (CPU_FAN1)
7 : SATA Power Output Connector (SATA_PWR1)
8 : SATA3 Connector (SATA3_0)
9 : M.2 Key-M Socket (M2_M1)
10 : M.2 Key-E Socket (M2_E1)
11 : M.2 Key-B Socket (M2_B1)
12 : COM Port PWR Setting Jumpers
PWR_COM4 (For COM Port4)
PWR_COM5 (For COM Port5)
PWR_COM6 (For COM Port6)
13 : USB 2.0 Connector (USB2_5_6)
14 : LVDS Panel Connector (LVDS1)
15 : eDP and LVDS Backlight Power Select (LCD_BLT_VCC) (BKT_PWR1)
16 : Digital Input / Output Power Select (JGPIO_PWR) (JGPIO_PWR1)
17 : TPM Header (TPM1)
18 : Chassis Intrusion Headers (CI1, CI2)
19 : ATX/AT Mode Jumper (SIO_AT1)
20 : CON_LBKLT_CTL Voltage Level (BLT_PWM2)
21 : Brightness Control Mode (BLT_PWM1)
22 : Backlight Power Connector (BLT_PWR1)
23 : Backlight Volume Control (BLT_VOL1)
24 : Clear CMOS Jumpers (CLRMOS1, CLRMOS2)
25 : Digital Input/Output Pin Header (JGPIO1)
26 : Digital Input / Output Default Value Setting (JGPIO_SET1)
27 : Internal COM Port Headers (COM4, 5, 6) (RS232)
28 : eDP and LVDS Panel Power Select (LCD_VCC) (PNL_PWR1)
29 : Buzzer Header (BUZZ2)
30 : DACC Jumper (DACC1)
31 : CC_TALK_OUT1
shared with COM6 (optional)
32 : SPDIF Header (SPDIF1)
33 : System Panel Header (PANEL1)
34 : USB 3.2 Gen1 Connector (USB3H1_3_4)

7
IMB-1005
35 : Battery Connector (BAT1)
36 : 3W Audio AMP Output Wafer (SPEAKER1)
37 : Front Panel Audio Header (HD_AUDIO1)
Back Side:
38 : ESPI Header (ESPI1)
39 : MIPI1 Socket (MIPI1 (optional))

8
1.4 I/O Panel
1 HDMI Port (HDMI2)
2 COM Port (COM1) (RS232/422/485)*
3 COM Port (COM3) (RS232/422/485)*
4 RJ45 LAN Port (LAN1)**
5 RJ45 LAN Port (LAN2)**
6 Audio Output : Green – Line Out
7 Audio Output : Pink – Mic In
8 USB 2.0 Ports (USB2_3_4)
9 USB 3.2 Gen1 Ports (USB3H_1_2)
10 D-Sub Port (VGA1)
11 COM Port (COM2) (RS232/422/485)*
12 HDMI Port (HDMI1)
23
14 5 6
891012 7
11
Activity/Link LED SPEED LED
** ere are two LEDs next to the LAN ports. Please refer to the table below for the
LAN port LED indications.
LAN Port LED Indications
Status Description
O No Link
Blinking Data Activity
On Link
Status Description
O 10Mbps connection
Orange 100Mbps/1Gbs connection
Green 2.5Gbps connection
ACT/LINK
LED
SPEED
LED
LAN Port
Pin RS232 RS422 RS485
1 DCD TX- RTX-
2 RXD TX+ RTX+
3 TXD RX+ N/A
4DTR RX- N/A
5 GND GND GND
6DSR N/A N/A
7RTS N/A N/A
8 CTS N/A N/A
9 PWR PWR PWR
10 N/A N/A N/A
COM1, 2, 3 Ports Pin Denition
* is motherboard supports RS232/422/485 on COM1, 2 and 3 ports. Please refer to the
table below for the pin denition. In addition, COM1, 2 and 3 ports (RS232/422/485) can be
adjusted in BIOS setup utility > Advanced Screen > Super IO Conguration. You may refer to
our user manual for details.

9
IMB-1005
1.5 Block Diagram
LVDS/eDP DDI
Intel
Alder
Lake-N
Nuvoton
NCT6126D
MDI
2.5G
IMB-1005J
FAN
RS232 x3
RS232/422/485 x3
Nuvoton
NUC121ZC2AE
SO-DIMM
DDR4
Channel A
2 x USB 3.2 Gen1
Connector
RJ45
Connector
MDI
2.5G
RJ45
Connector
Realtek
RTL8125BG
Line out & Mic in
Connector
& Header
Speaker header
Realtek
ALC662/
ALC897
M.2 Key M
Chrontel
CH7513
Realtek
RTL8125BG
CPU FAN x1
LVDS/eDP
By pass mode
HDMI
Connector
HDMI
Connector
VGA
Connector
Realtek
RTD2168
2 x USB 3.2 Gen1
Header
SATA Port
SATA x1
SPI
SMBUS
eSPI
UART x6
ITE
IT66318
DDI
TCP
ITE
IT66318
TCP
Asmedia
ASM1074
HDMI
HDMI
VGA
USB 2.0
USB 3.2
USB 2.0 x2
USB 3.2
Gen1 x2
USB 2.0 x2
USB 3.2
Gen1 x2
PCIe x1
PCIe x1
HDA
Audio
Realtek
ALC122
Audio
PCIe Gen3 x1 PCIe x1 slot
M.2 Key E
PCIe Gen3 x1
CNVi
USB 2.0
PCIe Gen3 x1/SATA
M.2 Key B
PCIe Gen3 x1
USB 3.2 Gen1
USB 2.0
SIM
Card
2x USB 2.0
Connector
USB 2.0 x2
2x USB 2.0
Header
USB 2.0 x2
1x USB 2.0
Connector
USB2.0 x1
DGIO GPIO x4
GPIO x4
BIOS /TPM
Header
Nuvoton
NCT3948

10
Chapter 2 Installation
is is a Mini-ITX (6.7-in x 6.7-in x 1.6-in, 17.0 cm x 17.0 cm x 4.1 cm) form factor
motherboard. Before you install the motherboard, study the configuration of your
chassis to ensure that the motherboard ts into it.
2.1 Screw Holes
Place screws into the holes to secure the motherboard to the chassis.
2.2 Pre-installation Precautions
Take note of the following precautions before you install motherboard components or
change any motherboard settings.
1. Unplug the power cord from the wall socket before touching any component.
2. To avoid damaging the motherboard components due to static electricity, NEV-
ER place your motherboard directly on the carpet or the like. Also remember to
use a grounded wrist strap or touch a safety grounded object before you handle
components.
3. Hold components by the edges and do not touch the ICs.
4. Whenever you uninstall any component, place it on a grounded antistatic pad or
in the bag that comes with the component.
5. Heatsink (e thermal solution of whole system needs to be designed addition-
ally.)
Make sure to unplug the power cord before installing or removing the motherboard. Failure to
do so may cause physical injuries to you and damages to motherboard components.
Do not over-tighten the screws! Doing so may damage the motherboard.
Before you install or remove any component, ensure that the power is switched o or the
power cord is detached from the power supply. Failure to do so may cause severe damage to
the motherboard, peripherals, and/or components.

11
IMB-1005
2.3 Installation of Memory Modules
IMB-1005 provides one 260-pin DDR4 (Double Data Rate 4) SO-DIMM slots, and
supports Single Channel Memory Technology.
e DIMM only ts in one correct orientation. It will cause permanent damage to the moth-
erboard and the DIMM if you force the DIMM into the slot in the incorrect orientation.
1. Please make sure to disconnect the power supply before adding or removing SO-
DIMMs or the system components.
2. It is not allowed to install a DDR, DDR2, or DDR3 memory module into a DDR4 slot;
otherwise, this motherboard and DIMM may be damaged.
Installing a SO-DIMM
Step 1. Align a SO-DIMM on the slot such that the notch on the SO-DIMM
matches the break on the slot.
Step 2. Firmly insert the SO-DIMM into the slot until the retaining clips at both
ends fully snap back in place and the SO-DIMM is properly seated.

12
2.4 Expansion Slots
ere are 1 PCI Express Gen3 slot, 3 M.2 sockets and 1 SIM socket on this motherboard.
PCIE slot: PCIE1 (PCIe x1 slot) is used for PCIe Gen3 x1 lane width card.
M.2 sockets: 1 x M.2 (Key E, 2230) with PCIe x1, USB 2.0 and CNVi for Wireless
1 x M.2 (Key B, 3042/3052) with PCIe x1, USB 3.2 Gen1, USB 2.0 and SIM for
4G/5G
1 x M.2 (Key M, 2242/2260/2280) with PCIe Gen3 x1 or SATA3 for SSD
SIM socket: 1x SIM socket connected to M.2 key B
M.2 Key-M Socket
(M2_M1)
M.2 Key-E Socket
(M2_E1)
M.2 Key-B Socket
(M2_B1)
Pin Signal Name Signal Name Pin
1 GND +3.3V 2
3 GND +3.3V 4
5NA NA 6
7NA NA 8
9 GND SATA_LED 10
11 NA +3.3V 12
13 NA +3.3V 14
15 GND +3.3V 16
17 NA +3.3V 18
19 NA NA 20
21 GND NA 22
23 NA NA 24
25 NA NA 26
27 GND NA 28
29 NA NA 30
31 NA NA 32
33 GND NA 34
35 NA NA 36
37 NA NA 38
39 GND NA 40
41 PERn0/SATA-B+ NA 42
43 PERp0/SATA-B- NA 44
45 GND NA 46
47 PETn0/SATA-A- NA 48
49 PETp0/SATA-A+ PERST# 50
51 GND CLKREQ# 52
53 PEFCLKn NA 54
55 PEFCLKp NA 56
57 GND NA 58
67 NA NA 68
69 PEDET +3.3V 70
71 GND +3.3V 72
73 GND +3.3V 74
75 GND
Pin Signal Name Signal Name Pin
1NA +3.3V 2
3 GND +3.3V 4
5 GND FuLL_Card_
Power_o 6
7 USB_D+ W_DISABLE1# 8
9 USB_D- WWAN_LED# 10
11 GND
21 GND NA 20
23 NA NA 22
25 NA NA 24
27 GND W_DISABLE2# 26
29 USB3_RX- NA 28
31 USB3_RX+ UIM_RESET 30
33 GND UIM_CLK 32
35 USB3_TX- UIM_DATA 34
37 USB3_TX+ UIM_PWR 36
39 GND NA 38
41 PERn0 NA 40
43 PERP0 NA 42
45 GND NA 44
47 PETn0 NA 46
49 PETP0 NA 48
51 GND PERST# 50
53 PEFCLKn CLKREQ# 52
55 PEFCLKp NA 54
57 GND NA 56
59 NA NA 58
61 NA NA 60
63 NA NA 62
65 NA NA 64
67 NA NA 66
69 PEDET NA 68
71 GND +3.3V 70
73 GND +3.3V 72
75 NA +3.3V 74
Pin Signal Name Signal Name Pin
1 GND +3.3V 2
3 USB_D+ +3.3V 4
5 USB_D- NA 6
7 GND NA 8
9 CNV_WGR_D1- CNV_RF_RESET 10
11 CNV_WGR_D1+ NA 12
13 GND MODEM_CLKREQ 14
15 CNV_WGR_D0- NA 16
17 CNV_WGR_D0+ GND 18
19 GND NA 20
21 CNV_WGR_CLK- CNV_BRI_RSP 22
23 CNV_WGR_CLK+
33 GND CNV_BGI_DT 32
35 PE Tp CNV_RGI_RSP 34
37 PETn CNV_BRI_DT 36
39 GND NA 38
41 PERp NA 40
43 PERn NA 42
45 GND NA 44
47 PEFCLKp NA 46
49 PEFCLKn NA 48
51 GND SUSCLK 50
53 CLKREQ# PERST0# 52
55 NA W_DISABLE1# 54
57 GND W_DISABLE2# 56
59 CNV_WT_D1- SMB_DATA 58
61 CNV_WT_D1+ SMB_CLK 60
63 GND NA 62
65 CNV_WT_D0- NA 64
67 CNV_WT_D0+ NA 66
69 GND NA 68
71 CNV_WT_CLK- NA 70
73 CNV_WT_CLK+ +3.3V 72
75 GND +3.3V 74

13
IMB-1005
2.5 Jumpers Setup
The illustration shows how jumpers are setup.
When the jumper cap is placed on pins, the
jumper is “Short.” If no jumper cap is placed
on pins, the jumper is “Open.” The illustration
shows a 3-pin jumper whose pin1 and pin2 are
“Short” when jumper cap is placed on these 2
pins.
Jumper Setting Description
eDP and LVDS Backlight Power Select (LCD_BLT_VCC)
(5-pin BKT_PWR1)
(see p. 4,No. 15)
Use this header to set up the backlight power of the LVDS connector and the panel backlight
power of BLT_PWM1.
Setting Description
1-2 LCD_BLT_VCC: +5V
(Default)
2-3 LCD_BLT_VCC:
+12V
4-5 LCD_BLT_VCC:
DC Input
COM Port PWR Setting Jumpers
(3-pin PWR_COM1~3 (For COM Port1~3))
(see p. 4,No. 1)
(3-pin PWR_COM4~6 (For COM Port4~6))
(see p. 4,No. 12)
e maximum current for per port is 1A, and the power supply is either 5V or 12V. Use the
jumper to set the power for COM port pin 9.
Setting Description
1-2 +5V (Default)
2-3 +12V
1 5
Digital Input / Output Power Select (JGPIO_PWR)
(3-pin JGPIO_PWR1)
(see p. 4,No. 16)
e maximum current JGPIO_PWR provides is 1A.
Setting Description
1-2 +12V
2-3 +5V (Default)
1
3
2
1 32
1 32

14
Clear CMOS Jumpers
(see p. 4, No. 24)
(3-pin CLRMOS1)
Setting Description
1-2 Normal (Default)
2-3 Clear CMOS
Chassis Intrusion Headers
(2-pin CI1, CI2)
(see p. 4, No. 18)
is motherboard supports CASE OPEN detection feature that detects if the chassis cover has
been removed. is feature requires a chassis with chassis intrusion detection design.
C I1
Setting Description
Close Active Case Open
Open Normal (Default)
C I2
Setting Description
Close Normal (Default)
Open Active Case Open
21
ATX/AT Mode Jumper
(2-pin SIO_AT1)
(see p. 4, No. 19)
e header provides auto boot function when AC power on. If you need the function, short
SIO_AT1 pin 1 and pin 2.
Setting Description
Open ATX Mode (Default)
Short AT Mode
Brightness Control Mode
(3-pin BLT_PWM1)
(see p. 4, No. 21)
Note: Please set to 1-2 when adjusting brightness by Brightness Control bar under OS.
Please set to 2-3 when adjusting brightness by BLT_VOL1.
Setting Description
1-2 From eDP PWM to
CON_LBKLT_CTL
2-3 From LVDS PWM to
CON_LBKLT_CTL
(Default)
CON_LBKLT_CTL Voltage Level
(3-pin BLT_PWM2)
(see p. 4, No. 20)
Setting Description
1-2 +3V (Default)
2-3 +5V
1 32
1 32
1 32
21

15
IMB-1005
Digital Input / Output Default Value Setting
(only setting for SIO_GPXX)
(3-pin JGPIO_SET1)
(see p. 4, No. 26)
e header is used for GPIO default value setting for either pull high or pull low. Pulling the
header to a high/low value means the voltage is anchored to VCC/GND, in a stable, non-
oating state.
Setting Description
1-2 Pull-High (Default)
2-3 Pull-Low
eDP and LVDS Panel Power Select (LCD_VCC)
(5-pin PNL_PWR1)
(see p. 4,No. 28)
Use this to set up the VCC power of the LVDS connector.
Setting Description
1-2 LCD_VCC: +3V
(Default)
2-3 LCD_VCC: +5V
4-5 LCD_VCC: +12V
Note: CLRMOS1 allows you to clear the data in CMOS. To clear and reset the system param-
eters to default setup, please turn o the computer and unplug the power cord from
the power supply. Aer waiting for 15 seconds, use a jumper cap to short pin 2 and
pin 3 on CLRMOS1 for 5 seconds. However, please do not clear the CMOS right aer
you update the BIOS. If you need to clear the CMOS when you just nish updating the
BIOS, you must boot up the system rst, and then shut it down before you do the clear-
CMOS action. Please be noted that the date, time, user default prole will be cleared
only if the CMOS battery is removed.
(2-pin CLRMOS2)
Note: CLRMOS2 allows you to clear the data in CMOS. e data in CMOS includes system
setup information such as system password, date, time, and system setup parameters.
To clear and reset the system parameters to default setup, please turn o the computer
and unplug the power cord, then use a jumper cap to short the pins on CLRMOS2.
Setting Description
Open Normal (Default)
Short Auto clear CMOS
when AC power on
1 32
1 5
21