ASROCK Rack 1U12XL C622 RPSU User manual

1U12XL_C622 RPSU
User Manual
Version 1.0
Published April 2018
Copyright©2018 ASRock Rack INC. All rights reserved.

Version 1.0
Published April 2018
Copyright©2018 ASRockRack Inc. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRockRack Inc.
Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identication or explanation and to the owners’ benet, without intent to
infringe.
Disclaimer:
Specications and information contained in this documentation are furnished
for informational use only and subject to change without notice, and should
not be constructed as a commitment by ASRockRack. ASRockRack assumes no
responsibility for any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRockRack does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or tness for a particular
purpose.
In no event shall ASRockRack, its directors, ocers, employees, or agents be liable
for any indirect, special, incidental, or consequential damages (including damages
for loss of prots, loss of business, loss of data, interruption of business and the
like), even if ASRockRack has been advised of the possibility of such damages
arising from any defect or error in the documentation or product.
is device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY
e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/
perchlorate”
ASRockRack’s Website: www.ASRockRack.com

Setting up the Server in a Restricted Access Location
• Access can only be gained by service persons or by users who have been instructed
about the reasons for the restrictions applied to the location and about any precautions
that shall be taken.
• Access is through the use of a tool or lock and key, or other means of security, and is
controlled by the authority responsible for the location.
• Leave enough clearance (25 inches in the front and 30 inches in the back of the rack) to
allow the front door to be opened completely and to allow for sucient airow.
• is product is for installation merely in a Restricted Access Location.
• is product is not suitable for use with visual display work place devices according to §2
of the the German Ordinance for Work with Visual Display Units.
Replaceable Batteries
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
Warning
When removal of the chassis lid required for servicing:
- Turn o power and unplug any power cords/cables, and
- Reinstall the chassis lid before restoring power.
Important Safety Instructions
Pay close attention to the following safety instructions before performing any of
the operation. Basic safety precautions should be followed to protect yourself from
harm and the product from damage:
• Operation of the product should be carried out by suitably trained, qualied, and
certied personnel only to avoid risk of injury from electrical shock or energy hazard.
• Disconnect the power cord from the wall outlet when installing or removing main
system components, such as the motherboard and power supply unit.
• Place the system on a stable and at surface.
• Use extreme caution when working with high-voltage components.
• When handling parts, use a grounded wrist strap designed to prevent static discharge.
• Keep the area around the system clean and clutter-free.
• Keep all components and printed circuit boards (PCBs) in their antistatic bags when
not in use.
• Handle a board by its edges only; do not touch its components, peripheral chips,
memory modules or contacts.

Contact Information
If you need to contact ASRockRack or want to know more about ASRockRack,
you’re welcome to visit ASRockRack’s website at www.ASRockRack.com; or you
may contact your dealer for further information.
ASRockRack Incorporation
6F., No.37, Sec. 2, Jhongyang S. Rd., Beitou District,
Taipei City 112, Taiwan (R.O.C.)

Contents
Chapter 1 Introduction 1
1.1 Shipping Box Contents 1
1.2 Specications 3
Chapter 2 Server System Overview 4
2.1 System Components 4
2.2 Internal Features 5
2.3 System Front Panel 7
2.4 System Rear Panel 7
2.5 Front Control Panel Buttons and LEDs 8
Chapter 3 Hardware Installation and Maintenance 10
3.1 Server Top Cover 11
3.2 Hard Disk Drive 13
3.3 Power Supply 18
3.4 System Fan 20
3.5LAN Mezzanine Card 21
3.6Chassis Cables 22

1U12XL-C622 RPSU
PB 1
English
Chapter 1 Introduction
ank you for purchasing 1U12XL-C622 RPSU, a reliable barebone system
produced under ASRockRack’s consistently stringent quality control. It delivers
excellent performance with robust design conforming to ASRockRack’s
commitment to quality and endurance.
1. Because the hardware specications might be updated, the content of this documentation
will be subject to change without notice. In case any modications of this documentation
occur, the updated version will be available on ASRockRack’s website without further
notice. If you require technical support related to this product, please visit our website for
specic information about the model you are using.
ASRockRack’s Website: www.ASRockRack.com
2. e illustrations shown in this manual are examples only, the actual system may dier
slightly .

2 3
English
1.1 Shipping Box Contents
Item Quantity
1U12XL-C622 RPSU Barebone(1U form factor) 1
System Boards (MB) 1
Power Supply Units 2
System Fans 6
HDD Backplane (BPB) 3
SSD/HDD(2.5” 7mm) Backplane (BPB) 2
Front Panel Board (FPB) 1
Power Distribution Boards (PDB) 1
1U CPU Passive Cooler 2
US Power Cords 2
2.5” to 3.5" HDD / SSD Mounting Bracket 12
MiniSAS HD Cable (1040mm) 1
MiniSAS HD Cable (700mm) 1
MiniSAS HD Cable (880mm) 1
PMBus Cable (500mm) 1
VGA Cable, DB9P/M to 2*8PIN HSG Cable (150mm) 1
COM Dongle Cable (300mm) 1
SATA Cable, (1140mm) 2
Power Y-Cable for backplane (700mm) 1
Power Cable, 8PIN CPU1 power (95mm) 1
Power Cable, 8PIN CPU2 power (500mm) 1
Power Cable, 24PIN main power (350mm) 1
Display Cable (1550mm) 1
SMBus Y Cable (650mm) 1
USB Cable, USB 2.0 cable (830mm) 1
Sliding Rail Kit 1
Cable Management Arm (Optional) 1
Support CD 1
Quick Installation Guide 1
IO Shield 2
Asset Tag 1
Air Duct 2
Plastic Standos 8
If any items are missing or appear damaged, contact your authorized dealer.

1U12XL-C622 RPSU
2 3
English
1.2 Specications
1U12XL-C622 RPSU
System Physical Status
Form Factor 1U Rackmount
Chassis Model 1U12L
Dimension
(D x W x H)
860 x 438.5 x 43.2 mm (33.9 x 17.2 x 1.7 inches)
Support MB Size EP2C622D16FM (12” x 10.5”)
Front Panel
Buttons • Power On/O button
• UID button
• System reset button
LEDs • 1 x Power status LED
• 1 x LAN activity LED
• 1 x HDD status LED
I/O Ports N/A
Hard Drive Bay
Front Side Drive
Bay
2 Hot-Swappable Bay for 2.5” 7mm SATA / SAS* HDD
*SAS HDD is going to be supported soon. Please contact our sales representa-
tives for the information of when it is available.
Front Side
Backplane
Dual single Backplanes for each drive
Internal Side
Drive Bay
12 Bay multi-function Hot-Swappable Bay for 3.5” or 2.5”
SATA/SAS HDD/SSD*
*2.5” SATA/SAS HDD/SSD is supported with bracket.
*A raid card is required to support SAS HDD/SSD. How many HDD/SSD are
supported vary depending on the type of raid card you use.
Internal Side
Backplane
3x Quad ports Backplane for drives*
*SFF-8482 connector
Power Supply
Type 1U, Redundant
Output Watts 700W
Eciency Platinum
System Fan
Fan 40 x 28 mm Fan x6

4 5
English
Chapter 2 Server System Overview
is chapter provides diagrams showing the location of important components of
the server system.
2.1 System Components
2 x Power Supply Units
12 x 3.5” HDD Carriers
2 x 2.5” HDD Trays
6 x System Fans
Server Board
Rear I/O Panel

1U12XL-C622 RPSU
4 5
English
2.2 Internal Features
1
2
5
6 7 8 9
3
4
12
13 14 15
22
27
11
16
17
10
18 19 20 21
23 24 25 26
28
29

6 7
English
No. From
1Serverboard
2Power Supply Unit (PSU) 2
3Power Supply Unit (PSU) 1
4Power Distribution Board (PDB)
5VGA Port & COM Port
6System Fan 6
7System Fan 5
8System Fan 4
9System Fan 3
10 System Fan 2
11 System Fan 1
12 HDD Backplane Board (BPB)
13 3.5" HDD 8 (SSATA2)
14 3.5" HDD 9 (SSATA3)
15 3.5" HDD 10 (SSATA4)
16 3.5" HDD 11 (SSATA5)
17 HDD Backplane Board (BPB)
18 3.5" HDD 4 (SATA4)
19 3.5" HDD 5 (SATA5)
20 3.5" HDD 6 (SATA6)
21 3.5" HDD 7 (SATA7)
22 HDD Backplane Board (BPB)
23 3.5" HDD 0 (SATA0)
24 3.5" HDD 1 (SATA1)
25 3.5" HDD 2 (SATA2)
26 3.5" HDD 3 (SATA3)
27 2.5" SATA HDD 0 (Hot-swapable)
28 2.5" SATA HDD 1 (Hot-swapable)
29 USB 2.0 Ports

1U12XL-C622 RPSU
6 7
English
2.3 System Front Panel
24 13
No. Description
1 2 x USB 2.0 Ports
2 2.5" SATA HDD Tray 0 (SSATA0)
3 Control Panel Buttons and LEDs
4 2.5" SATA HDD Tray 1 (SSATA1)
2.4 System Rear Panel
24
1356
No. Description
1 2 x Power Supply Units
2 I/O Shield (depends on the specication of the server board)*
3 1 x LAN Mezzanine Card Slot
4Rea r Vent*
5COM Port
6VGA Port
*e locations of I/O shield and rear vent may vary depending on the system and server board models.

8 9
English
2.5 Front Control Panel Buttons and LEDs
Front Control Panel
4 53
16 2
No. Description
1 Power Button and LED
2 System Reset Button
3 LAN Status LED*
4 HDD Status LED*
5 System Fault LED
6 UID Button and LED*
*Please be noted that the functions are supported depending on the type of the server board.
System Reset Button
When the system is completely unresponsive, press the system reset button to reboot the
server without shutting it o and initialize the system.
UID Button
Press the UID button to toggle the front panel UID LED and the baseboard UID LED on
and o. You are able to locate the server you’re working on from behind a rack of servers.
Power Button
Press the power switch button to toggle the system power on and standby/sleep modes.
To remove all power from the system completely, disconnect the power cord from the
server.

1U12XL-C622 RPSU
8 9
English
Status LED Denitions
Power LED
Status Description
Green Power on
O Power o
UID LED
Status Description
Blue System identication is active.
O System identication is disabled.
LAN LED
Status Description
Green Link between system and network and no access
Blinking Green Network access
HDD Status LED
Status Description
O No one or more HDDs are connected.
Green e corresponding HDD is connected.
HDD Fail LED
Status Description
O Normal
Red e corresponding HDD fails.

10 11
English
Chapter 3 Hardware Installation and
Maintenance
is chapter helps you assemble the chassis and install components.
Before You Begin
Before you work with the server, pay close attention to the “Important Safety Instructions”
at the beginning of this manual.
1. Make sure the server is powered o.
Power down the server if it is still running.
(1) Press the Power button to power o the server from full-power mode to standby-
power (sleep) mode. e Power LED at the front turns from solid green to blinking
green.
(2) Disconnect the power cord rst from the AC outlet and then from the server.
e power LED turns o.
2. Ensure you have a clean and stable working environment. Avoid dust and dirt because
contaminants may cause malfunctions.
3. Ground yourself properly before touching any system component. A discharge of static
electricity may damage components. Wear a grounded wrist strap if available.
Installing Procedures
e followings are prerequisite to be installed.
• 3.5" or 2.5" HDD(s)
• Power Supplies (Pre-installed)
• Server Board (Pre-installed)
• Power Distribution Board (Pre-installed)
• HDD Backplanes (Pre-installed)
• Fans (Pre-installed)
e server is not completely powered down when you press the Power button on the front
panel. e Power button lets the server toggle between Power On and Standby (Sleep)
modes. Some internal circuitry remain active in the Standby mode. To remove all power
from the system completely, be sure to disconnect the power cord from the server.
1. Some components are already pre-installed. Simply properly connect the relavant cables
before or aer installation. See the Quick Installation Guide for more details.
2. Refer to the user manual of the server board you use for instructions on how to install
server board components.

1U12XL-C622 RPSU
10 11
English
3.1 Server Top Cover
Removing the Server Top Covers
2
3
1
1
1
2
3
1. Remove the screws that secure the top covers to the chassis.
2. Push the top front cover toward the front of the chassis to remove the cover from the
locked position.
3. Li up and remove the top rear cover.
1. Before removing the top cover, power o the server and unplug the power cord.
2. e system must be operated with the chassis top cover installed to ensure proper cooling.

12 13
English
Installing the Server Top Covers
2
3
3
3
3
2
1
1. Lower the top covers on the chassis, making sure the side latches align with the cutouts.
2. Slide the top front cover toward the rear.
3. Secure the top covers with the screws.

1U12XL-C622 RPSU
12 13
English
3.2 Hard Disk Drive
3.2.1 Installing a Hard Disk Drive into a 3.5" Hard Drive Carrier
1. Open the hard drive release lever.
2. Lower a 3.5" HDD into the carrier.
3. Carefully align the hard drive with the carrier and make sure it is well seated.
4. Close the hard drive release lever to secure the hard drive to the carrier.
5. Reverse the procedures to remove a 3.5" hard drive.
1
2
3

14 15
English
3.2.2 Installing a 2.5" Hard Disk Drive(or Solid-State Drive) into a 3.5" Hard
Drive Carrier
1. Install the 2.5" HDD/SSD into bracket and align with the 2 screw holes on bracket.
2. Secure it to the bracket the screws.
3. Open the hard drive release lever.
4. Lower the 2.5" HDD/SSD assembly into a 3.5" hard drive carrier.
5. Carefully align the assembly with the carrier and make sure it is well seated. Close the
hard drive release lever to secure the hard drive assembly to the carrier.
1
2
2
4
3
5