Assa Abloy KP10G77 User manual

Installation Instructions For
Keypad 10 ine ock KP10G77
A7113E
8/08
Copyr ght © 2005, 2007,2008, SARGENT Manufactur ng, an ASSA ABLOY Group company. All r ghts reserved.
Reproduct on n whole or n part w thout the express wr tten perm ss on of SARGENT Manufactur ng s proh b ted.

800-810-WIRE (9473) • .sargentlock.com • A7113E
12/15/07 © SARGENT Manufacturing C mpany 2005, 2007. All rights reserved.
8/14/08 Copyr ght © 2005, 2007,2008, Sargent Manufactur ng Company, an ASSA ABLOY Group company. All r ghts reserved.
Reproduct on n whole or n part w thout the express wr tten perm ss on of Sargent Manufactur ng Company s proh b ted.
Table of Contents
General Descr pt on............................................................................1
Spec f cat ons .....................................................................................1
Parts Breakdown.............................................................................2-3
Features ..............................................................................................4
Installat on Instruct ons................................................................5-12
Programm ng Instruct ons
Engl sh ...................................................................................12-15
Cha n Programm ng ....................................................................16
Transact on Log ................................................................................17
Gu de De Progammat on (French) ...................................................18
Page
1
2
3
4
5
6
7
8

1
A7113E • 800-810-WIRE (9473) • .sargentlock.com
Keypad 10 ine ock
8/14/08 Copyr ght © 2005, 2007,2008, Sargent Manufactur ng Company, an ASSA ABLOY Group company. All r ghts reserved.
Reproduct on n whole or n part w thout the express wr tten perm ss on of Sargent Manufactur ng Company s proh b ted.
General Description
The SARG NT Keypad 10 Line Lock is designed for areas which require authorized entry. It is a
self-contained microprocessor-controlled keypad with non volatile solid-state memory. The keypad will
hold a total of 100 different User Codes. User Codes “01” and “03” are utilized for Master Code and
Supervisory Code, respectively. All programming is done at the keypad, with over 1,100,000 possible
user combinations.
This lock is operated by four (4) “C” batteries with a life span of approximately 50,000 cycles.
A portable infrared printer (52-2069) may be used to download user information.
• Latch bolt - 1/2" standard
3/4" available (41-prefix)
• Deadlocking latch
• Outside lever controlled by keypad or key retracts latch bolt
• Inside lever retracts latch
• Locks furnished for 1-3/4" doors only
• U.L. Listed
Specifications
1
2

2800-810-WIRE (9473) • .sargentlock.com • A7113E
12/15/07 © SARGENT Manufacturing C mpany 2005, 2007. All rights reserved.
Keypad 10 ine ock
8/14/08 Copyr ght © 2005, 2007,2008, SARGENT Manufactur ng, an ASSA ABLOY Group company. All r ghts reserved.
Reproduct on n whole or n part w thout the express wr tten perm ss on of SARGENT Manufactur ng s proh b ted.
Parts Breakdown
ITEM PART NUMBER DESCRIPTION NO. REQ’D
1*10-0523 “B” Inside lever/regular and 30- 1
*10-2204 “J” Inside lever/regular and 30- 1
*10-0503 “L” Inside lever/regular and 30- 1
*10-0547 “P” Inside lever/regular and 30- 1
*10-0536 “B” Inside lever/75 handicap warning 1
*10-2247 “J” Inside lever/75 handicap warning 1
*10-0514 “L” Inside lever /75 handicap warning 1
*10-0558 “P” Inside lever/75 handicap warning 1
See SARGENT web page for Costal Series Levers.
2 *10-0790 Rose scalp "G" 2
2A *10-0798 Rose scalp "L" 2
410-0792 Spacer bushing 2
510-3048 Inside rose spring assembly (not finished) 1
6 01-9170 Through-bolt screws 2
6A 10-0802 Plastic screw holder 2
7 01-4388 8 X 1 SELF TAP SCREW 1
7A 82-0443 Turn lever cover plate, plastic -black. not shown 1
9*10-2875 Inside escutcheon assembly 1
9A 52-2400 Controller/circuit board assembly only 1
10 45-1340 Flat head screw (security) 1
10A 52-0069 Battery cover only 1
11 01-0297 SOCKET ALLEN SAFETY KEY 1
12 *52-2340 Outside escutcheon & keypad 1
12A 52-2299 Keypad assembly only 1
13 01-1500 SELF TAP SCREW TYPE "AB" 2
14 52-0033 Fire stop plate and screws 1
15 10-2642 77 Lockbody (std, 10, 21, 23, 30, SC, SE, VA & VS prefixes only) 1
15A 10-2643 77 Lockbody (60, 63, 64 prefixes only) 1
15B 10-2644 77 Lockbody (70, 72, 65-73, 65-73P lockbody) 1
16 10-3049 Outside rose spring assembly (not finished) 1
17 10-0019 Cylinder spacer 1
17A 13-3613 Schlage (SC) cylinder (provide keying details) 1
17B 13-3614 Schlage (SE) cylinder (provide keying details) 1
17C 13-3713 Cylinder (10-Signature) 1
18 10-0312 Cylinder retainer 1
18A 10-0313 Cylinder retainer for removable core, 1
Interchangeable core & Keso
19 13-3266 Cylinder (standard) provide keying details 1
20 *10-2251 “B” Lever outside standard cylinder 1
*10-2205 “J” Lever outside standard cylinder 1
*10-0502 “L” Lever outside standard cylinder 1
*10-0546 “P” Lever outside standard cylinder 1
*10-0525 “B” Outside lever/30-competitive cylinder 1
*10-2206 “J” Outside lever/30-competitive cylinder 1
*10-0503 “L” Outside lever/30-competitive cylinder 1
*10-0547 “P” Outside lever/30-competitive cylinder 1
*10-0535 “B” Outside lever/standard cylinder 76 handicap warning 1
*10-2246 “J” Outside lever/standard cylinder 76 handicap warning 1
*10-0513 “L” Outside lever/standard cylinder 76 handicap warning 1
*10-0557 “P” Outside lever/standard cylinder 76 handicap warning 1
See SARGENT web page for Costal Series Levers.
21 Key (provided with cylinder) A/R
22 *10-2000 2-3/4" Backset latch (standard) 1
22A 10-2053 3-3/4" Backset latch (23 prefix) 1
22B *10-2058 5" Backset latch (25 prefix) 1
22C *10-2634 3/4" Throw (41 prefix) 1
23 01-4414 Screw for standard front and strike 4
24 *08-0312 #800 Strike 1
24A *08-0066 #808 Strike (28-prefix) 1
25 *10-2052 Screw pack- standard (screws (latch, strike, #3) & push pin tool) 1
*10-2070 Screw pack- 28- prefix (screws (front, strike, #3) &push pin tool) 1
26 52-2300 Screw pack (includes #’s 7, 11, 13, 14, 28, 28A, 29) 1
27 08-0055 Strike Box- standard 1
28 01-1157 8-32unc-2ax 1 1/4 1
28A 01-9063 WAS ER 1
29 01-1119 P FL D 8-32 X 1 1/2 1
30 10-0043 Lever Retainer Push Pin, Not Shown 1
3
*Specify Finish

3
A7113E • 800-810-WIRE (9473) • .sargentlock.com
Keypad 10 ine ock
8/14/08 Copyr ght © 2005, 2007,2008, SARGENT Manufactur ng, an ASSA ABLOY Group company. All r ghts reserved.
Reproduct on n whole or n part w thout the express wr tten perm ss on of SARGENT Manufactur ng s proh b ted.
Parts Breakdown (Continued)

4800-810-WIRE (9473) • .sargentlock.com • A7113E
12/15/07 © SARGENT Manufacturing C mpany 2005, 2007. All rights reserved.
Keypad 10 ine ock
8/14/08 Copyr ght © 2005, 2007,2008, SARGENT Manufactur ng, an ASSA ABLOY Group company. All r ghts reserved.
Reproduct on n whole or n part w thout the express wr tten perm ss on of SARGENT Manufactur ng s proh b ted.
Features
KP10G77
• Non volatile memory
• Motor driven, battery operated cylindrical lock
• Battery operated with 4 each “C” Alkaline Batteries
• Low battery alert–4 chirps after code entry
• Option Code available to sound horn every time keypad is pressed
• xternal remote “request to exit” connector
• xternal battery input connector included to power unit in event of battery failure
• 100 users total: one Master Code, one Supervisory Code, with the rest being standard codes,
passage codes, or one time only codes
• All programming done at keypad
• Operates utilizing any two to six digits per code. Digits may be repeated and codes may start
with zero
• Minimum 40,000 cycles per set of batteries
• Cylinder override provided
• ntry of three wrong User Codes disables all codes for ten seconds. Green L D flashes
• Piezo horn can be heard with each keystroke or turned off by Master or Supervisory Code
• Last 15 transactions can be output to portable printer via infrared link
Keypad
• Made of ultraviolet stable material
• L D’s indicate valid or invalid entries
• Green L D indicates unlocked. Yellow L D indicates unit is in programming mode
• Flashing green and yellow L D’s indicate lock in passage mode
• Infrared L D for transaction output. Indicates last 15 valid codes
Items included in your KP10G77 Keypad Cylindrical Lock:
• Outside scutcheon with Keypad
• Motorized Cylindrical Lock with cylinder
• Inside escutcheon with circuit board and battery pack
• Batteries (4 “C”)
• Tools
4

5
A7113E • 800-810-WIRE (9473) • .sargentlock.com
Keypad 10 ine ock
8/14/08 Copyr ght © 2005, 2007,2008, SARGENT Manufactur ng, an ASSA ABLOY Group company. All r ghts reserved.
Reproduct on n whole or n part w thout the express wr tten perm ss on of SARGENT Manufactur ng s proh b ted.
Left Hand
Hinges Left.
Open inward.
“LH”
Left Hand
Reverse Bevel
Hinges Left.
Open Outward
“LHRB”
Right Hand
Hinges Right
Open Inward.
“RH”
Right Hand
Reverse Bevel
Hinges Right.
Open Outward.
“RHRB”
Installation Instructions
Step #2 Door Preparation
Prepare door according to appropriate template (see website www.sargentlock.com):
• For metal door template, see 4486 and 4494
• For wood door template, see A7332 (scale paper template ships with product) and 4375-1
• Prior to installation, all holes must be free of burrs, debris and sharp edges
• If doors are not properly reinforced per ANSI115.2, commercially available reinforcements
should be installed
Step #1 Verify Hand and Bevel of Door
Stand on outside/locked side of the door when determining the door hand
5
Wood Door Preparation
Left hand
hinges left
open inward
LH
Left hand
reverse bevel
hinges left
open outward
LHRB
Right hand
hinges right
open inward
RH
Right hand
reverse bevel
hinges right
open outward
RHRB
Inside of
door
Outside of
door

6800-810-WIRE (9473) • .sargentlock.com • A7113E
12/15/07 © SARGENT Manufacturing C mpany 2005, 2007. All rights reserved.
Keypad 10 ine ock
8/14/08 Copyr ght © 2005, 2007,2008, SARGENT Manufactur ng, an ASSA ABLOY Group company. All r ghts reserved.
Reproduct on n whole or n part w thout the express wr tten perm ss on of SARGENT Manufactur ng s proh b ted.
Step #3 Frame Preparation for Strike
on Fire Rated Exterior Doors–
Install Weather Conduit (P/ 52-2847)
as shown below
Step #4 atch and Fire Stop Plate Installation
1. Install latch with beveled bolt facing the strike
2. Attach with two screws, but DO NOT tighten completely at this time
3. Attach Fire Stop Plate with two screws
ote: Required for all Fire Rated doors
Important: Latch bevel must match door
bevel and deadlocking latch must stop on
strike when door is closed
Fire Rated Doors– Install Fire Stop Plate
(P/ 52-0033) as shown below

7
A7113E • 800-810-WIRE (9473) • .sargentlock.com
Keypad 10 ine ock
8/14/08 Copyr ght © 2005, 2007,2008, SARGENT Manufactur ng, an ASSA ABLOY Group company. All r ghts reserved.
Reproduct on n whole or n part w thout the express wr tten perm ss on of SARGENT Manufactur ng s proh b ted.
Screws partially
tightened
For wood
door only
Inside
of door
1
2
Lock Preset to:
• Through-bolt location– 12 & 6 o'clock
• Door thickness– 1-3/4" thick- see below for other door conditions
Adjustment for different through-bolt and door thickness:
• Remove outside lever (usually keyed), scalp and spacer bushing
• Rotate mounting plate to either align with through-bolt holes in door,
or adjust for proper door thicknesses (see markings on through-bolt)
• Reinstall spacer bushing (to align with back of lever) scalp and lever
Step #5 ock Installation
IMPORTA T:
Door must remain open
during installation.
Use door stop.
3
1-3/4" thick door
2" thick door
Through-bolt
holes
Rotate to match
through-bolt holes in door
Spacer bushing
1. Feed wires into the lock body hole from outside of door
2. Install lock body into cross-bore hole from outside of the door (locked side)
3. Lock body must engage both the latch unit prongs and tail piece (as shown)
IMPORTA T:
Lockbody
must be
centered in
the door.

8800-810-WIRE (9473) • .sargentlock.com • A7113E
12/15/07 © SARGENT Manufacturing C mpany 2005, 2007. All rights reserved.
Keypad 10 ine ock
8/14/08 Copyr ght © 2005, 2007,2008, SARGENT Manufactur ng, an ASSA ABLOY Group company. All r ghts reserved.
Reproduct on n whole or n part w thout the express wr tten perm ss on of SARGENT Manufactur ng s proh b ted.
Step #6 Securing the ock to Door
1A. If wood door, feed wires up through
the routed channel as shown
1B. If metal door, feed wire connector within the
door core and out hole on inside of door
2. Attach inside rose assembly and spacer
bushing and secure with screws shown
Step #7 Installation of Outside Escutcheon
• From the outside of the door,
feed keypad wires through fire
stop plate and to the inside of
the door. Lift plate cover if needed.
•IMPORTA T – Fire stop
plate cover must lay flat
before installing the keypad
to avoid interference

9
A7113E • 800-810-WIRE (9473) • .sargentlock.com
Keypad 10 ine ock
8/14/08 Copyr ght © 2005, 2007,2008, SARGENT Manufactur ng, an ASSA ABLOY Group company. All r ghts reserved.
Reproduct on n whole or n part w thout the express wr tten perm ss on of SARGENT Manufactur ng s proh b ted.
Step #8 – Security of Outside Escutcheon
• From the inside of the door, use
the #8-32 x 1 1/4” round head
screw with the flat washer to
attach the escutcheon thru the
lower lug
• Straighten escutcheon and tighten
the #8-32 round head screw
Step #9 – Installation of Inside Escutcheon
• Plug the smaller lockbody
wires into the inside
escutcheon. Access holes
vary based on wood or
metal door application
• Plug keypad ribbon
cable connector into
inside escutcheon
IMPORTA T: Both wire
plug connectors go on
only one way. Do not
offset the connectors.
If not seated, keypad
will not function properly

10 800-810-WIRE (9473) • .sargentlock.com • A7113E
12/15/07 © SARGENT Manufacturing C mpany 2005, 2007. All rights reserved.
Keypad 10 ine ock
8/14/08 Copyr ght © 2005, 2007,2008, SARGENT Manufactur ng, an ASSA ABLOY Group company. All r ghts reserved.
Reproduct on n whole or n part w thout the express wr tten perm ss on of SARGENT Manufactur ng s proh b ted.
Step #10 Securing of Inside Escutcheon
• Remove black plastic battery cover with security hex wrench (provided)
• Carefully tuck the wire into the routed groove in wood door. The remainder can fit within
bottom portion of escutcheon. Make certain that wires are not pinched by obstructions in escutcheon
• Place inside escutcheon flat against the door
• Secure inside escutcheon with one flat head screw thru interior of inside escutcheon and into
post of exterior escutcheon
• Secure bottom of escutcheon with flat head screw and ferrule
Step #11 Test ockset
• Rotate inside lever
to test for latch
bolt retraction
• Place key into
cylinder and rotate
key for latch
bolt retraction
• Tighten latch
bolt screws on
edge of door
• Test keypad
operation per
manual's
instructions

11
A7113E • 800-810-WIRE (9473) • .sargentlock.com
Keypad 10 ine ock
8/14/08 Copyr ght © 2005, 2007,2008, SARGENT Manufactur ng, an ASSA ABLOY Group company. All r ghts reserved.
Reproduct on n whole or n part w thout the express wr tten perm ss on of SARGENT Manufactur ng s proh b ted.
Step #12 – Battery Installation
• Place (4) C batteries into the compartment as indicated inside escutcheon
• Attach battery cover to inside escutcheon and secure with #8-32 x 3/8" security screw
DO OT OVER TIGHTE
How to Remove Outside ever Only
1.Insert key, rotate 45° clockwise and hold
2.Depress lever retainer with push pin tool (provided)

12 800-810-WIRE (9473) • .sargentlock.com • A7113E
12/15/07 © SARGENT Manufacturing C mpany 2005, 2007. All rights reserved.
Keypad 10 ine ock
8/14/08 Copyr ght © 2005, 2007,2008, SARGENT Manufactur ng, an ASSA ABLOY Group company. All r ghts reserved.
Reproduct on n whole or n part w thout the express wr tten perm ss on of SARGENT Manufactur ng s proh b ted.
Programming Instructions
The 10 Line Keypad Lock can support 100 users. ach user is assigned a User Number in addition to
the code used for entry.
6
Example: US R US R US R COD *
TYP NUMB R (2-6 DIGITS)
Master 01 1 2 3 4
Supervisor 03 3 0 3 0 3 0
Standard 04-97 2 6 5
Special Factory 98
10 Sec. Time Preset 99 1 3 6 8
How to Change Cylinder (if required)
1. With outside lever in hand-
use standard pliers; pull out
cylinder retainer
2. Remove key and cylinder from lever
3. Insert new cylinder
4. Secure by pressing cylinder retainer
flush with shelf*
* OT SHOW
Washers
(only 30- prefix)
Cylinder
retainer
Cylinder
Outside
lever
Key
Cylinder
spacer

13
A7113E • 800-810-WIRE (9473) • .sargentlock.com
Keypad 10 ine ock
8/14/08 Copyr ght © 2005, 2007,2008, SARGENT Manufactur ng, an ASSA ABLOY Group company. All r ghts reserved.
Reproduct on n whole or n part w thout the express wr tten perm ss on of SARGENT Manufactur ng s proh b ted.
Programming Instructions (Continued)
6
This Keypad 10 ine ock has 99 User Codes available for programming purposes.
• The Master Code is always User “01”. The Master Code assigns the Emergency and Supervisory Codes.
It is also used for programming. Users are deleted through the Master Programming Code only.
• The Emergency Code is always User “02”. The Emergency Code has an unlock time of 10 seconds.
• The Supervisory Code is always User “03”. The Supervisory Code allows temporary lockout of selected
users, changes duration of unlock time, requests infrared interrogation output, and may add additional
User Codes.
• The first User Code will be User “04” or higher. User numbers do not have to be used or entered
sequentially.
• User codes “98” and “99” have a factory-set unlock time of ten seconds. This allows a handicapped person
extra time which would not be required by other users.
To Begin Programming:
The Keypad 10 Line Lock is preset at the factory with Master Code “1234”. Entering 1234 * will unlock
the lock allowing the lever handle to retract the latchbolt.
Initial Set-Up Procedures:
• The following are typical procedures to follow when setting up your KP10G77 Keypad.
• If a mistake is made during any of procedures, depress the “*” several times until the yellow LED goes out.
• If no keystroke is made in a 30 sec. time frame, the programming up to that point will default and you will
have to start over.
All of the following procedures start with 99#.
If after the last “*” is depressed, the yellow ED does not go out, depress “*” once more.
Change Master Code:
• 1234* (Yellow LED Begins to Blink Slowly) This example uses the Factory Default Master Code
• 50# 1# 01# New Master Code* (Yellow LED Blinks Quickly)
• New Master Code* (Yellow LED Blinks Slowly) *(Yellow LED Goes Out)
To Enter the Emergency Code: (Unlock Duration is Factory Set at 10 Sec)
• Master Code* (Yellow LED Begins to Blink Slowly)
• 50# 1# 02# Emergency Code* (Yellow LED Blinks Quickly)
• Emergency Code* (Yellow LED Blinks Slowly) * (Yellow LED Goes Out)"
To Enter the Supervisory Code:
• Master Code* (Yellow LED Begins to Blink Slowly)
• 50# 1# 03# Supervisory Code* (Yellow LED Blinks Quickly)
• Supervisory Code* (Yellow LED Blinks Slowly) *(Yellow LED Goes Out)

14 800-810-WIRE (9473) • .sargentlock.com • A7113E
12/15/07 © SARGENT Manufacturing C mpany 2005, 2007. All rights reserved.
Keypad 10 ine ock
8/14/08 Copyr ght © 2005, 2007,2008, SARGENT Manufactur ng, an ASSA ABLOY Group company. All r ghts reserved.
Reproduct on n whole or n part w thout the express wr tten perm ss on of SARGENT Manufactur ng s proh b ted.
To Enter a User Code:
• Supervisory or Master Code* (Yellow L D Begins to Blink Slowly)
• 50# 1# User Number (04-97)# User Code* (Yellow L D Blinks Quickly)
• User Code* (Yellow L D Blinks Slowly)* (Yellow L D Goes Out)
To Enter a Passage (Maintained Mode) Code: When Passage Mode is used, the same User Code
must be used to Re-lock the Lock.
• Supervisory or Master Code* (Yellow L D Begins to Blink Slowly)
• 50# 2# User Number (04-97)# User Code* (Yellow L D Blinks Quickly)
• User Code* (Yellow L D Blinks Slowly)* (Yellow L D Goes Out)
To Enter a One Time User Code:
• Supervisory or Master Code* (Yellow L D Begins to Blink Slowly)
• 50# 3# User Number# User Code* (Yellow L D Blinks Quickly)
• User Code* (Yellow L D Blinks Slowly) * (Yellow L D Goes Out)
To Deactivate “Beep” With the Depression of Each Key:
• Supervisory or Master Code* (Yellow L D Begins to Blink Slowly)
• 30# 0# 0# (Yellow L D Continues to Blink Slowly)
• * (Yellow L D Blinks Quickly)
• * (No Beep on Depression and Yellow L D Blinks Slowly)
• * (No Beep on Depression and Yellow L D Goes Out)
To Reactivate “Beep” With the Depression of Each Key:
• Supervisory or Master Code* (Yellow L D Begins to Blink Slowly)
• 30# 0# 1# (Yellow L D Continues to Blink Slowly)
• * (Yellow L D Blinks Quickly)
• * (Beep on Depression and Yellow L D Blinks Slowly)
• * (Beep on Depression and Yellow L D Goes Out)
To Clear the Entire Memory:
• Master Code* (Yellow L D Begins to Blink Slowly)
• 46# 00000# 00000# (Yellow L D Continues to Blink Slowly)
• * (Yellow L D Blinks Quickly)
• * (No Beep on Depression and Yellow L D Goes Out)
• PAUS , Yellow L D Begins to Blink Again
• * (Yellow L D Goes Out)
Note: This Deletes ALL Codes, including Master, mergency and Supervisory. The Master Code is set back to
1234, Door Number to 0001 and Unlock time 5 Sec. If the Master Code is not known, Factory Assistance will be
required to clear the memory. 1-800-810-WIR .
To Program Door Numbers into Keypad:
• Master Code* (Yellow L D Begins to Blink Slowly)
• 43# 0# Door Number# (must be four digits) (Yellow L D Blinks Slowly)
• * (Yellow L D Begins to Blink Quickly)
• * (Yellow L D Blink Slowly)
• * (Yellow L D Goes Out)
All of the following procedures start with 99# (continued).
If after the last “*” is depressed, the yellow ED does not go out, depress “*” once more.

15
A7113E • 800-810-WIRE (9473) • .sargentlock.com
Keypad 10 ine ock
8/14/08 Copyr ght © 2005, 2007,2008, SARGENT Manufactur ng, an ASSA ABLOY Group company. All r ghts reserved.
Reproduct on n whole or n part w thout the express wr tten perm ss on of SARGENT Manufactur ng s proh b ted.
All of the following procedures start with 99# (continued).
If after the last “*” is depressed, the yellow ED does not go out,
depress “*” once more.
To Interrogate Transaction og:
• Supervisory or Master Code* (Yellow LED Begins to Blink Slowly)
• 70# 0# 0# (Yellow LED Blinks Slowly)
• * (Yellow LED Begins to Blink Quickly)
• * (Yellow LED Goes Out)
For additional information, see “Transaction Log”.
old an infrared printer up to the
red infrared LED (as shown). An
P82240B Infrared Printer can
be used to download information
from the keypad to a printout.
Sargent also offers a Data Transfer Device (DTD) To Interrogate the lock.
Go to WWW.SARGENTLOCK.COM for information.
ote: Seq. # 1 is the
programming request
to output the entries.
Sequence numbers
2-6 are the actual
entries.
Door #5666
Seq User Trans
1 001 003
2 003 001
3 003 001
4 020 001
5 003 001
Door
Number
Transaction
Number
User
Number
Transaction
type
To Reset / Clear Transaction og:
• Supervisory or Master Code* (Yellow L D Begins to Blink Slowly)
• 76# 00000# 00000# (Yellow L D Blinks Slowly)
• * (Yellow L D Begins to Blink Quickly)
• * (Yellow L D Goes Out)
To Delete a User Number:
• Master Code* (Yellow L D Begins to Blink Slowly)
• User Number# (Yellow L D Blinks Slowly)
• * (Yellow L D Begins to Blink Quickly)
• * (Yellow L D Blinks Slowly)
• * (Yellow L D Goes Out)
To Disable / Enable a User Number:
• Supervisory or Master Code* (Yellow L D Begins to Blink Slowly)
• 56# 0# = nable, 1# = Disable, User Number# (04-99) (Yellow L D Blinks Slowly)
• * (Yellow L D Begins to Blink Quickly)
• * (Yellow L D Blinks Slowly)
• * (Yellow L D Goes Out)
To Set Unlock Time:
• Master Code* (Yellow L D Begins to Blink Slowly)
• 85# Time Duration# (01-99 Sec) 0# (Yellow L D Blinks Slowly)
• * (Yellow L D Begins to Blink Quickly)
• * (Yellow L D Blinks Slowly)
• * (Yellow L D Goes Out)
Note: The Unlock Time is Adjustable for Momentary Operation. A 5 second unlock time is recommended to
extend battery life. Once the unlock time is entered, it is the same for ALL users except 02, 98 and 99 which are
factory set for 10 seconds.

16 800-810-WIRE (9473) • .sargentlock.com • A7113E
12/15/07 © SARGENT Manufacturing C mpany 2005, 2007. All rights reserved.
Keypad 10 ine ock
8/14/08 Copyr ght © 2005, 2007,2008, SARGENT Manufactur ng, an ASSA ABLOY Group company. All r ghts reserved.
Reproduct on n whole or n part w thout the express wr tten perm ss on of SARGENT Manufactur ng s proh b ted.
Type User umber User Code
1 05 875
3 12 2226
2 08 5444
1 50 3367
Using Master Code 4732 and above information, the lock would be programmed as follows:
99# 4732* 50# 1# 05# 875* 875* 3# 12# 2226* 2226* 2# 08# 5444* 5444* 1# 50# 3367*
3367**
If all user codes are the same type, it is not necessary to enter the type number with each
entry. The type number has to be entered with the first user code only.
The format now simplifies to:
99# Master or Supervisor Code* 50# Type# User Number a# User code a* User Code a*
UNb# UCb* UCb* UNc# UCc* UCc*....... UN_# UC_* UC_**
An example with three user codes is shown below:
Type User umber User Code
1 07 77
1 15 67832
1 91 7568
Using Master Code 45988 and above information, the lock would be programmed as follows:
99# 45988* 50# 1# 07# 77* 77* 15# 67832* 67832* 91# 7568* 7568**
To chain the User Number delete procedure:
99# Master Code* User Number a#** UNb#** UNc#**....... UN_#****
Using the information from the above example:
99# 45988* 07#** 15#** 91#****
Chain Programming
When programming multiple User Numbers and Codes into the
10 Line Keypad Lock, it is not necessary to leave and re-enter the
programming mode (50) for each entry. Multiple entries may be chained
together and the three different types of user codes (Standard, Passage
and One Time) may be mixed.
The format to be used is as follows where:
“T” is the Type of user code with “1” Standard, “2” Passage and “3” One Time.
“UN_” is User Number (04-99)
“UC_” is User Code (2 to 6 digits) which correlates with the User Number 99# Master or Supervisor
Code* 50# Type# User Number a# User Code a*
User Code a* T# UNb# UCb* UCb* T# UNc# UCc* UCc* ...... T# UN_# UC_* UC_**
An example with four user codes is shown below:

17
A7113E • 800-810-WIRE (9473) • .sargentlock.com
Keypad 10 ine ock
8/14/08 Copyr ght © 2005, 2007,2008, SARGENT Manufactur ng, an ASSA ABLOY Group company. All r ghts reserved.
Reproduct on n whole or n part w thout the express wr tten perm ss on of SARGENT Manufactur ng s proh b ted.
old an infrared printer up to the
red infrared LED (as shown). An
P82240B Infrared Printer can
be used to download information
from the keypad to a printout.
ote: Seq. # 1 is the
programming request to output
the entries. Sequence numbers
2-6 are the actual entries.
Door #5666
Seq User Trans
1 001 003
2 003 001
3 003 001
4 020 001
5 003 001
Door
Number
Transaction
Number
User
Number
Transaction
type
Transaction og
7
To output the last 15 entries, enter 99 # Supervisory or Master Code * 70 # 0 # 0 # **.
Door umber
• 4 Digits
• Up to 9999 different doors, assigned by user
Transaction umber
• Single digit - 1-6
• Latest transaction - 1
• Oldest transaction - 6
User umber
• Three digits - 001 through 099
• User numbers assigned at time of programming
Transaction Types
• 001 =Access granted
• 003 = Log printed
Optional Equipment
• Printer Paper (6 Rolls) - 52-0034 used for infrared printers
• Auxiliary Power Unit (APU) 52-2065 - used to unlock unit if
batteries are too weak and cylinder is not used.
• Infrared Printer - 52-2069 - used to download the user and
transaction type.
• Remote Unlocking - 52-2071 - used for remote unlocking
of keypad 10 Line Lock. When remote unlocking feature is
used, the latchbolt can be retracted by turning the lever
handle. Use a QC2A inge.
Remote
unlocking
connector
placement
TB-2
ElectroLynx®
As part of their promise to provide innovative, fast and effective high
sec rity sol tions to their c stomers, ASSA ABLOY Gro p companies
offer ElectroLynx®, a niversal q ick-connect system that simplifies the
electrification of the door opening.
ElectroLynx®is a registered trademark of ASSA ABLOY Inc.

18 800-810-WIRE (9473) • .sargentlock.com • A7113E
Keypad 10 ine ock
8/14/08 Copyr ght © 2005, 2007,2008, SARGENT Manufactur ng, an ASSA ABLOY Group company. All r ghts reserved.
Reproduct on n whole or n part w thout the express wr tten perm ss on of SARGENT Manufactur ng s proh b ted.
Guide de programmation
La serrure à clavier KP10G77 peut accomoder 100 utilisateurs. On doit assigner à chacun un numéro
d’utilisateur, en plus de son code d’entrée.
Example: Type d’usager Numéro d’usager Code d’usager
(2 à 6 chiffres)
Maître 01 1 2 3 4
Urgence 02 2 2 2 2 2
Superviseur 03 3 0 3 0 3 0
Ordinaire 04 à 97 2 6 5
Spécial usine 98
10 secondes 99 1 3 6 8
Serrure à clavier KP10G77
99 codes d’utilisateurs disponibles à la programmation
• Le code maître est toujours l’utilisateur programmation. Les utilisateurs sont
• Le code d’urgence est toujours l’utilisateur temps de déverrouillage de 10 secondes.
• Le code superviseur est toujours modification du temps de déverrouillage,
• Le premier code d’utilisateur sera
• Les codes ‘’98’’ et ‘’99’’ établis en les personnes handicapées.