Assa Abloy Interlock Elevation Window Control System User manual

August 2013 ©copyright by ASSA ABLOY
Elevation
Window Control System
Keypad installation and user guide

2
RAIN SENSOR
Read these instructions prior to the activation of the keypad.
Save this user guide in a safe place for future reference.
TOUCH SCREEN ACTIVATION:
Never use sharp instruments, such as a pencil or pen, to press touchscreen keys.
To prevent damage to the screen, always press the touch screen with your fingertip.
CAUTION:
Changes or modifications to this product not approved by ASSA ABLOY could result in warranty being voided.
IMPORTANT:
Correct installation of the network is paramount to the function of the keypad.
Ensure all details are carried out as per the wiring diagram in the installation instructions.
FINISH CARE:
This keypad is designed to provide the highest standard of product quality and performance.
Care should be taken to ensure a long lasting finish. When cleaning is required use a clean, damp,
nonabrasive cloth. The use of lacquer thinners, caustic soaps, abrasive cleaners or polishes for cleaning
may result in damage to this product.
NEED HELP:
For assistance with this product please visit: www.assaabloy.co.nz
Or call on: 0800 NZ LOCKS (0800 69 56257)
WARNINGS
NETWORK ADAPTOR
ACTUATOR

Elevation
Window Control System
INSTALLER - SETUP AND CONFIGURATION
1. Basic Operating Principle 4
2. Powering up the System 4
3. Calibration 4
4. System Setup and Configuration 5-7
a. Allocating Actuators to Zones
b. Checking Zone Allocation
5. Modifying System Configuration 8-10
a. Removing Actuators from Zones
b. Adding Actuators to Zones
6. Restoring Previous Settings 11
7. Rain Sensor Setup 12-17
a. Adding Rain Sensors to Zones
b. Removing Rain Sensors from Zones
c. Configuring Rain Sensor Function
8. Restarting the Keypad 18
9. Trouble Shooting 18
USER GUIDE
10. Home Page 19
11. Selecting A Window Position 20
12. Backlit Home Button 21
13. PIN Code Creation 22
14. Service Details 22
15. System Warnings 23-25
16. Rain Sensor/Actuator Location Matrix 26-27
17. Frequently Asked Questions 28-29
18. Zone Names 29
19. Wiring Diagram 30
20. Notes 31
CONTENTS PAGE
3

INSTALLER - SETUP AND CONFIGURATION
BACKLIT HOME BUTTON
When configuring your network, Actuators are loaded into groups known as Zones.
Multiple Zones are available. Each actuator can only be allocated to one Zone.
BASIC OPERATING PRINCIPLE
Ensure all wiring connections are complete before powering up.
Ideally the Actuators should be powered up before the Keypads. This ensures the Keypads register
all Actuators on the network. If powering up the system is not possible in this manner, and Actuators have not been
recognized, press Restart Keypad in the Setup page. Then proceed to Zone Setup to allocate the Actuators
that have not previously registered.
POWERING UP THE SYSTEM
Once all Actuators are registered the system will proceed to a calibration screen.
Press Calibrate Actuators. All Actuators will move open and close twice.
If a warning is displayed stating ‘Window Obstructed’ this means that an Actuator has performed a safety stop.
Locate this window. Press Home and then Close All. Only the obstructed window will close.
Fix the obstruction. Then press Calibrate Actuators to continue.
CALIBRATION – Ensure there are no obstructions blocking the windows
4
ACTIVE TOUCH SCREEN

An Actuator can only be assigned to one Zone.
This screen will appear once the auto calibration is complete.
Press Yes to commence Zone Setup.
No will take you to the Home page where options of
Open All, Close All, and Setup will be available.
Note: There are a total of 30 Zone names to choose from.
Zone names cannot be customised.
See page 29 for the list of the names.
There are two ways to assign Actuators to zones:
1. If serial numbers are known (from page 26):
If not proceed to section 2 below.
Use the arrow keys to scroll, matching the serial number
on the left with the desired Zone on the right.
Press Add to Zone and confirm your selection.
2. If serial numbers are not known:
Press each Actuator button on the left.
The corresponding Actuator will open.
Note: After 5 minutes it will close automatically.
Visually locate this Actuator. Then use the arrow keys on the right
to select the desired Zone.
Press Add to Zone and confirm your selection.
The window will now close if open.
Note: Pressing the Actuator button again will also close the window.
Repeat either process until all Actuators are allocated to your
desired Zones.
Press Exit & Save then Yes to save your Zone settings.
SYSTEM SETUP AND CONFIGURATION
Allocating Actuators to Zones:
5

6
Method 1.
3. Press any opening position and observe which windows move
to check that the Actuators are assigned to the correct Zones.
Repeat steps 1, 2, and 3 until all Zones have been checked.
SYSTEM SETUP AND CONFIGURATION continued
Checking Zone Allocation:
1. Use the arrow buttons to scroll through the Zone list.
2. Press the zone name, e.g. Lounge 1

Checking Zone Allocation continued:
You can view Zones to see which Actuators have been assigned
to a particular Zone.
1. Press View Zones.
2. Use the appropriate arrow buttons to scroll through either
the Actuator list or the Zone list.
Note: No changes can be made in this screen.
SYSTEM SETUP AND CONFIGURATION continued
Method 2.
7

4. Using the arrow keys on the right, scroll to the Zone from which
you want to remove an Actuator.
5. Press the Actuator button on the left. The corresponding Actuator
will open. Locate this Actuator and check that it is the one you wish
to remove.
6. If it is, press Remove From Zone and confirm your selection
(the Actuator will close automatically when confirmed).
7. If it is not, press the Actuator button again to close this Actuator.
MODIFYING SYSTEM CONFIGURATION
Removing Actuators from Zones:
Note: All Rain Sensors must be removed from a Zone before removing
Actuators from that Zone.
1. From the Home page, press Setup.
2. Press Zone Setup.
3. Press Remove from Zone.
This now takes you to a screen where you can remove Actuators
from Zones.
8

Removing Actuators from Zones continued:
8. Then use the arrow keys to scroll to the next Actuator in the Zone
and repeat the process until the desired Actuator is found.
Note: Actuator locations may have also been previously noted
on pages 26 & 27.
9. Press Setup to exit.
You will not be prompted to save at this point.
The reason for this is explained in the Restore Previous section
(page 11). However you can save if you wish by exiting the
Zone Setup page.
1. Press Zone Setup.
MODIFYING SYSTEM CONFIGURATION continued
Adding Actuators to Zones: Mainly used for modifications to Zone Setups.
9

3. Press the Actuator button on the left.
The corresponding Actuator will open.
4. Locate this Actuator then use the arrow keys on the right
to select the desired Zone.
Once matched press Add to Zone and confirm your selection.
Important: Repeat the process ensuring all Actuators are allocated
to your desired Zones before exiting and saving.
5. Press Exit & Save, and then Yes to save your modified Zone settings.
Note: Serial Number location method can be used if required,
see page 5.
MODIFYING SYSTEM CONFIGURATION continued
Adding Actuators to Zones continued:
2. Press Add To Zone.
This now takes you to a screen where you can add Actuators to Zones.
10

Restore Previous will enable you to restore the previously saved
Zone settings.
Not recommended for use if Rain Sensors are installed.
Rain Sensor settings will be deleted and will need to be
reprogrammed if Restore Previous is used.
1. Press Setup on the Home screen to display this screen.
2. Press Restore Previous.
You will be prompted Yes or No.
1. Press Yes to restore the previously saved Zone settings.
Explanation continued from page 9:
Restore Previous will only restore the previously saved settings,
not necessarily your original saved settings.
RESTORING PREVIOUS SETTINGS
11

3. Press Add RS To Zone.
RAIN SENSOR SETUP
Adding Rain Sensors to Zones:
Note: A maximum of 4 Rain Sensors can be connected to a Network.
1. Press Setup on the Home screen to view this screen.
2. Press Rain Sensor Setup.
12

5. Use the arrow keys to match the Rain Sensor to the appropriate
Zone.
6. Press Add to Zone.
Confirm that the message displays the correct number of Rain
Sensors online.
4. Press Yes to confirm and proceed to the next screen.
Press No or Setup to go back to the Setup screen.
Note: The system may take a few minutes to register the Rain Sensors.
Go back to the Setup page and then back into the Rain Sensor Setup page
if the incorrect number of Rain Sensors has been displayed.
IMPORTANT:
•Rain Sensors are assigned to Zones, and before Rain Sensors can
be added, Zones must be setup.
•Rain Sensors can be added to multiple Zones.
•The serial number on a Network Adaptor and the dwelling position
of the Rain Sensor it interfaces with must be noted during
installation to know which Zone(s) each Rain Sensor is to be
assigned to. Refer to page 26.
RAIN SENSOR SETUP continued
Adding Rain Sensors to Zones continued:
13

7. Press Exit & Save then Yes to confirm your selection.
Note: If all Rain Sensors have been added to all Zones the Add to Zone
page will appear blank.
14
RAIN SENSOR SETUP continued
Adding Rain Sensors to Zones continued:
6. Confirm your selection by pressing Yes.
A confirmation screen will be displayed and the system will return
to the Add RS To Zone page.
The Rain Sensor will no longer be displayed on the left hand side of
the screen once assigned to a Zone.
If more than one Zone is desired for a particular Rain Sensor, scroll
to that Zone and repeat the process above.
The Rain Sensor will reappear once a new Zone is displayed.

1. Press Remove RS From Zone.
RAIN SENSOR SETUP continued
Removing Rain Sensors from Zones:
Confirm that the message displays the correct number of Rain
Sensors online.
2. Press Yes to proceed to the next screen.
15
2

Configuring Rain Sensor Function:
RAIN SENSOR SETUP continued
Removing Rain Sensors from Zones continued:
3. Use the arrow keys to scroll to the desired Zone and match it
with the desired Rain Sensor.
4. Press Remove from Zone.
5. Confirm your selection by pressing Yes.
A confirmation screen will be displayed and then the system will
return to the Remove From Zone page.
Note: The Rain Sensor will no longer be displayed on the left hand
side once removed from the Zone.
6. Press Exit & Save once all desired Rain Sensors have been removed.
Note: Restore Previous will not restore Rain Sensor settings.
These will be deleted. See page 11.
There are options in the Rain Sensor Setup page that allow you to
set the way the Zones react in the event of rain.
These options are :
•Disable or Enable Reopen: in the event of rain, the Actuators
will close. If Enable Reopen is selected the Actuators will
automatically reopen to their previous positions once the
Rain Sensor has dried.
•Shut or Vent: in the event of rain the Actuators will move
to this position.
The above options are customized as follows:
1. Press Configure Functions.
16
3

2. Use the arrow Keys to scroll to the desired Zone.
3. Toggle the functional options by pressing the buttons.
The options displayed are the current settings.
Default settings are: Disable Reopen and Shut.
The other options are shown in the picture.
RAIN SENSOR SETUP continued
Configuring Rain Sensor Function continued:
Basic Rain Sensor Function
Once the Rain Sensor detects rain, it will immediately activate
the windows to start closing to the chosen configuration,
i.e. shut or vent, and displays the icon shown here.
The windows will reopen 15 minutes after the Rain Sensor has dried.
Note: The sensor can be placed in open areas if desired and does
not need to be next to the assigned zone/window.
The Rain Sensor will not be activated by dew.
17
4

Operate the Zone on the Home page displaying an explanation mark.
The window that does not move corresponds to the Actuator that has not
been recognized. Check for loose wiring to that Actuator.
If no loose wires are found then the Actuator could be at fault.
To remove this Actuator from the Zone so the warning is no longer displayed,
carry out the following steps:
Note: If a Rain Sensor is assigned to this Zone it will need to be removed before the
Actuator can be removed.
1. Press Setup, Zone Setup.
2. Press Remove From Zone.
3. Press the right hand side arrow keys to scroll to the Zone that is displaying an
explanation mark on the Home page.
4. If necessary, press the left hand side arrow keys and scroll to the Actuator
that is coloured red.
5. Press Remove From Zone.
6. Press Setup to go back to the Zone Setup page then press Setup again to go
back to the Setup page.
7. Press Yes to save your settings.
The warning should now be resolved in the Home page.
If not, contact your installer.
TROUBLE SHOOTING
18
RESTARTING THE KEYPAD
This function is used when a Zone warning is displayed on the Keypad indicating
that one or more of the Actuators have not been recognized by the Keypad.
1. Wait for at least 2 minutes.
If the warning is still present push Restart Keypad in the Setup page.
The Keypad should now recognize the Actuator.
If it does not, then follow the steps in the next section.
There are two ways to assign Actuators to zones:
1. If serial numbers are known (from page 26):
If not proceed to section 2 below.
Use the arrow keys to scroll, matching the serial number
on the left with the desired Zone on the right.
Press Add to Zone and confirm your selection.
2. If serial numbers are not known:
Press each Actuator button on the left.
The corresponding Actuator will open.
Note: After 5 minutes it will close automatically.
Visually locate this Actuator. Then use the arrow keys on the right
to select the desired Zone.
Press Add to Zone and confirm your selection.
The window will now close if open.
Note: Pressing the Actuator button again will also close the window.
Repeat either process until all Actuators are allocated to your
desired Zones.
Press Exit & Save then Yes to save your Zone settings.
5

19
LABEL DEFINITION
Zone Names A maximum of 3 Zones are shown on the Home page at any one time.
Press the Zone name to display the 4 preset window position options. Refer next page.
Zone Status This shows the current opening position of the corresponding windows in that Zone.
Scroll up / down Press these buttons to scroll through the entire Zone list. Displayed if more than 3 Zones
are set up.
Setup Pressing this button takes the user to another screen to allow several setup options.
Open all Pressing this button will open all Actuators on the network.
Close all Pressing this button will close all Actuators on the network.
ZONE NAMES
SCROLL
UP
ZONE STATUS
SCROLL
DOWN
USER GUIDE
6
HOME PAGE

SELECTING A WINDOW POSITION
After pressing any of the pre-set positions below, the Actuators will automatically move to that position.
Press Stop at any time to stop the Actuators. A symbol will be displayed next to the Zone highlighting the fact that
the window is not at a pre-set position.
Note: Maximum default chain length is 300mm. Your window might be limited to a shorter length due to restrictions.
Contact your window manufacturer if the chain length needs to be adjusted.
Full:
Press this button to fully open the windows in that Zone.
Vent:
Press this button to vent the windows in that Zone.
This position will open the window 15mm
Half:
Press this button to open the windows in that Zone half way.
Shut:
Press this button to shut the windows in that Zone.
20
7