Assa Abloy Yale nexTouch NTM 610 Assembly Instructions

1
Yale Locks
Z-Wave+ System Integrators Guide
Yale nexTouch Sectional Mortise Keypad Lock
NTM 610/615/620/625/630/635/640/645

2
Contents
Yale Z-Wave+ Info .........................................................................................................................................3
Supported Command Classes ....................................................................................................................... 3
Association Table .......................................................................................................................................... 4
Notifications Table ........................................................................................................................................4
Configurable Parameters .............................................................................................................................. 7

3
Yale Z-Wave+ Info
Manufacturer ID: Assa Abloy (0x0129)
Z-Wave Device Type: Door Lock Keypad
Z-Wave Role Type: Listening Sleeping Slave (LSS)
Product ID: 0x0A00
Product Type ID:
0x8008 –NTM620/625/640/645-ZW2 (Touch Screen interface)
0x8008 –NTM610/615/630/635-ZW2 (Push Button Interface)
Supported Command Classes
Command Class Z-Wave+ Info
Command Class Manufacturer Specific
Command Class Security
Command Class Device Reset Locally
Command Class Power Level
Command Class Version
Command Class Battery*
Command Class Door Lock*
Command Class Door Lock Logging*
Command Class Schedule Entry Lock*
Command Class User Code*
Command Class Time Parameters*
Command Class Time*
Command Class Association*
Command Class Association Group Info*
Command Class Notification*
Command Class Configuration*
Command Class Firmware Update Md*
* Command Class Requires Security

4
Association Table
Group ID
Maximum Nodes
Description
Commands
1
5
Lifeline
Command_Class_Battery, Battery_Report ;
Command_Class_Notification, Notification_Report;
Command_Class_Configuration, Configuration_Report;
Command_Class_Device_reset_locally,
Device_Reset_locally_notification
Notifications Table:
Alarm Reports
Alarm
type
Alarm Level
Description
Notification
Type
Event
Master Code
changed.
0x70
0x00
Master code was
changed at keypad
0x06
0x12
0xFB
Master code was
changed over RF
0x06
0x0E
User added
0x(01-max
users)
User added. Alarm
level = user slot
number
0x06
0X0E
User deleted
0x21
0x(01-max
users)
User was deleted.
Alarm level = user slot
number
0x06
0X0D(0X0C)
Tamper Alarm
0xA1
0x01
keypad attempts
exceed code entry
limit
0x06
0X10
0x02
front escutcheon
removed from main
0x06
0xFE
RF Operate Unlock
0x19
0x01
by RF module
0x06
0X04
Keypad Unlock
0x13
0x(01-max
users)
Where Alarm level
represents user slot
number (0xFB =
Master Code)
0x06
0X06
Manual Lock
0x15
0x01
by key cylinder or
inside thumb-turn
0x06
0x01
0x02
by touch function
(lock and leave)
0x06
0x01
0x03
By inside button
0x06
0x01

5
RF Operate Lock
0x18
0x01
by RF module
0x06
0x03
Keypad Lock
0x12
0x (01 –max
users)
Where Alarm level
represents user slot
number
0x06
0x05
Non Access
0x26
0x(01-max
users)
A Non Access Code
was entered at the
lock.
Where alarm level
represents user slot
number
0x06
0xFE
Low Battery
Alarms**
0xA8
0x (Current %)
Critical Battery Level
(Starting at 4.6V)
0x08
0x0B
0xA7
0x (Current %)
Low Battery
(Starting at 4.4V)
0x08
0x0A
Auto Lock Operate
Locked
0x1B
0x01
Auto re-lock cycle
complete, locked.
0x06
0x09
Duplicate Pin-code
error
0x71
0x (01-max
users)
Where Alarm level
represents user slot
number
Alarm generated in
response to add user
RF cmd.
This alarm is not
generated when
attempting to add
duplicate pin at the
keypad. The lock
simply denies it and
plays the “Denied”.
Trying to duplicate the
master code will result
in a 0x71 0x00 alarm
report.
0x06
0x0F
RF Module Power
Cycled
0x82
0x00
Power to RFM was
restored, sent by RF
module. The lock
doesn’t send any
alarm to the RF
module when power
is cycled.
0x08
0x01
Disabled user
entered at keypad
0x83
0x(01-max
users)
A disabled user pin
code was entered at
the keypad
0x06
0xFE
Valid user but
outside of schedule
0x84
0x(01-max
users)
A valid user can be
both a normal user
and a Non-Access
user. If a non-access
0x06
0xFE

6
user is out of schedule
this alarm will be sent
instead of the non-
access alarm.
Door Position
Sensor
0x2B
0x00
Door Opened
0x06
0x16
0x01
Door Closed
0x06
0x17
0x02
Door Propped (Door
Open for longer than
configurable door
propped time)
0x06
0xFE
Daily Repeating
Schedule
Set/Erased
0x60
0x(01-max
users)
Schedule(s) has been
set/erased for
specified user ID
0x06
0xFE
Daily Repeating
Schedule
Enabled/Disabled
0x61
0x(01-max
users)
Schedule(s) has been
enabled/disabled for
specified user ID
0x06
0xFE
Year Day Schedule
Set/Erased
0x62
0x(01-max
users)
Schedule(s) has been
set/erased for
specified user ID
0x06
0xFE
Year Day Schedule
Enabled/Disabled
0x63
0x(01-max
users)
Schedule(s) has been
enabled/disabled for
specified user ID
0x06
0xFE
All Schedule Types
Erased
0x64
0x(01-max
users)
Schedule(s) has been
set/erased for
specified user ID
0x06
0xFE
All Schedule Types
Enabled/Disabled
0x65
0x(01-max
users)
Schedule(s) has been
enable/disabled for
specified user ID
0x06
0xFE
Deadbolt
Secured/Unsecured
0x2A
0x0000
Deadbolt Secure
0x06
0XFE
0x0001
Deadbolt
Extended/Secured
0x06
0xFE
Lever Rotated (Rx)
0x29
0x0000
Lever was rotated.
WGA10 does not
distinguish between
inside/outside levers
0x06
0xFE
** - The Yale lock also supports a 3rd low battery alarm, too low to operate. This alarm is sent out as a
Battery Report (with value = 0xFF) through the Battery Command Class. This is the last low battery
alarm level before the product stops functioning.

7
Configurable Parameters
Configuration
Parameters
Parameter
Number
Size
Description
Silent mode on/off
1
1 byte
Level control, 1 = High Volume, 2 = Low Volume, 3 =
Silent. Default is 1 or High Volume
Auto Relock on/off
2
1 byte
0x00 = OFF, 0xFF = ON default is 0x00 or OFF
Auto Relock time
3
1 byte
1 to 180 seconds default is 03 seconds
Wrong Code Entry Limit
4
1 byte
3 to 10 default is 5 times
Language
5
1 byte
1=English, 2=Spanish, 3=French default is 1= English
Shut down time (after
wrong code entries)
7
1 byte
10 to 180 seconds default is 60 seconds
operating mode
8
1 byte
00 = normal mode (this is the default mode)
01 = vacation mode, keypad lockout
02 = privacy mode, no keypad. RF Unlock will work
03 = passage mode, Lock is permanently unlocked.
One Touch Locking
11
1 byte
0x00 = OFF, 0xFF = ON default is 0xFF or ON.
Privacy Button
12
1 byte
0x00 = OFF, 0xFF = ON default is 0x00 or OFF
Lock Status LED
13
1 byte
0x00 = OFF, 0xFF = ON default is 0xFF or ON.
Reset To Factory
Defaults
15
1 byte
01 = Lock will execute Reset To Factory.
No default value
Escape Return Mode
16
1 byte
0x00 = OFF, 0xFF = ON default is 0x00 or OFF
Enables the Escape Return mode of operation for the
lock.
Door Propped Timer
18
1 byte
10 to 2540 second. This value is represented as
seconds X 10. (ie a value of 4 would mean a door
propped timer of 40 seconds) Set to 0x00 to disable
Door Propped Alarm. Default = 0x00 (OFF)

8
DPS Alarms(Ax sensor)
19
1 byte
0x00 = OFF, 0xFF = ON Default is 0xFF or ON.
Used to enable/disable door condition alarms for locks
that support a door position sensor. Any lock that does
not support DPS will always report 0x00.
Deadbolt Installed
20
1 byte
0x00 = NO deadbolt , 0xFF = YES deadbolt
Read only parameter. Some locks contain optional
deadbolt hardware. This parameter is used to
determine if one is installed.
Eco Mode On/Off
21
1 byte
0x00 = OFF, 0xFF = ON default is 0x00 or OFF
If supported switches lock to lower power mode of
operation with reduced sound and led brightness.
Privacy Mode with
Deadbolt
22
1 byte
0x00 = OFF, 0xFF = ON default is 0x00 or OFF
If enabled then extending the deadbolt will put the lock
into Privacy Mode.
Lock Body Alarms Mask
23
1 byte
Each bit controls one alarm. 1 = alarm enabled, 0 =
alarm disabled.
0xFF = All Alarms on, Default is 0xFF.
Bit 0: DPS Alarm (AX) (Duplicate of parameter 19.
Values should be tied together)
Bit 1: Deadbolt Alarm
Bit 2: Lever Rotated (Rx)
Bit 3 –7: Not Used
*** - Additional hardware required. These parameters are only active if the optional Door Position
Switch has been installed with the lock.