Assa Abloy K100-622 User manual

K100-622 Aperio Series
Wireless Cabinet Lock
Installation Instructions
HES, Inc.
Phoenix, AZ
1.800.626.7590
www.hesinnovations.com
NOTE: The wireless hub and hub bracket are included with the K100-622H model.
Package Contents
Recommended Tools
Optional Additional Tools:
Gang box to mount hub
Cam Lock for Key Override
Drill, Drill bits: 1/16”, 3/16”, 1/2”
Approved iCLASS or Prox ID
credential.
Flathead drivers 3/32”, 3/16”
Phillips drivers P0, P2
Pencil, Wire Stripper, Level,
Square, Pliers
Wireless Frequency: 2.4 GHz, IEEE 802.15.4, using AES 128-bit encryption
Hub Power Requirement: 8–24 Volts Direct Current (VDC), 250 milliamps (mA)
Lock Battery Type: Lithium AA Cell, 1.5 Volts (V) (Energizer L91 Ultimate Lithium)
Battery Life: 50,000 cycles
Operating Temperature: 32 °F to 122 °F (0 °C to 50 °C)
FCC Part 15 Compliant, IC Compliant
Credentials Supported:(-PA) Low Frequency model: HID PROX, EM PROX
(-SE) High Frequency model: iCLASS, iCLASS SEOS , iCLASS SE, ISO14443B UID,
Mifare, Mifare Plus, Desfire SE, Desfire EV1, NFC
Product Specifications
For technical support please call 1-800-626-7590
QR codes can be scanned
with a smart phone app
K100-622
Tips and Videos
QR Codes
Strike Plate
Shaft Extension
2-56 x 1-1/4”
1X
Energizer L91 Ultimate
Lithium Batteries
2X
Double door bracket
Lock Body
8-32 x 1 1/4”
Breakaway
3X
8-32 x 2 1/2”
2X
8-32 x 2 3/4”
2X
6-32 x 5/16”
3X
6 x 1/2”
5X
2-56 x 7/16”
2X
Key Override
Cam
Key Override Paddle
Template
Screws
Reader
8-32 x 5/16”
1X
Hub Bracket
Wireless Hub
3080076.004, Rev. B 1

System Overview
The K100-622 series wireless cabinet lock provides
access control to a cabinet or drawer without the complexity and
expense of running wires to the cabinet or drawer. The K100-622 series lock connects to an access control through
a communication hub (included with the K100-622H). The communication hub connects to the access control
system with Wiegand wiring typical of a Wiegand Reader.
When a credential card is presented to the reader on the lock the request for access is sent wirelessly to the
communication hub. The communication hub then communicates through Wiegand wiring to the access control
system where the decision is made to grant or deny access.
Installation Process
Testing the Lock
Connecting the Hub
(K100-622H only)
Mounting the Lock
Locating and Mounting the Hub
(K100-622H only)
3080076.004, Rev. B 2

Choosing the hub location
NOTE: The following applies primarily
to the K100-622H Model with
included hub.
It is recommended that the hub be
mounted near the top of a wall, on the
ceiling or above the ceiling to reduce
potential for interference, and be facing
toward the lock for best performance.
For a stable and reliable radio link, it is
recommended that the hub is located
within fifty (50) feet of the lock. A
maximum of two interior walls
between the hub and lock is
recommended
Recommended locations:
A: Wall Mount
B: Ceiling Mount
C: Wall Mount, Adjacent Room
NOTE: The hub is not rated for use in
plenum air spaces.
Mounting the Hub
NOTE: The following applies primarily to the K100-622H Model with included hub.
The included adapter plate can be used to mount the hub on a single or double gang box.
A
B
C
Mounting the Hub
3080076.004, Rev. B 3

Connecting the Hub
NOTE: The following applies primarily to the K100-622H Model with included hub.
The Aperio®Hub connects to the Access Control system via Wiegand wiring. The hub requires 8–24 VDC power
(250mA). The hub includes three Form C relays that can be used to transmit latch bolt position status, low
battery signal, and a tamper signal. The hub connects to the cabinet lock wirelessly.
NOTE 1: The Green LED input is used to grant access to the cabinet lock. If the Green LED signal is not available
to indicate approved access, the approval input can be activated by a relay with “NO” attached to Green
LED and “C” to GND.
NOTE 2: The Red LED input is used to indicate access denied.
If the RED LED signal is not connected, the lock will
flash RED three times when a non-approved card is presented indicating loss of connection to the hub
rather than access denied. Any other codes may be reference on the LED reference card.
1. CONNECT the Wiegand D1, D0, red and green LED signals.
3. CONNECT Latchbolt Position, Low
Battery, and Tamper Switch Detection
Form C relays.
2. CONNECT 8–24 VDC and ground (250 mA).
Connecting the hub
3080076.004, Rev. B 4

Testing the Lock with the Access Control System
NOTE: With the hub connected to power and the access control system, the lock is tested with a known good
credential to confirm it will open as desired when installed.
1. REMOVE the battery cover from the
lock body.
2. PASS the wire and shaft from the
reader through the lock body.
3. CONNECT the wire (the wire is
keyed) from the reader to the
socket in the lock battery
compartment.
4. INSTALL the batteries and ENSURE
correct orientation; the lock will self
test and beep once.
5. PRESENT a
credential known
to the access
control system.
6. IF a green LED, indicating
access is granted, is lit;
THEN TWIST the knob to
retract the latch.
7. REFER to the LED
reference card for any
other c0des.
8. REMOVE the batteries, UNPLUG
the cable carefully, and
SEPARATE the lock and reader
to prepare for installation.
Testing the lock
3080076.004, Rev. B 5

***CAUTION***
The Installer must ensure the lock can be opened before closing the cabinet at the end of these
installation instructions.
Mounting the Lock
NOTE: The K100-622 reader and lock body can be
oriented in several ways to accommodate
various cabinets and drawers.
1. ESTABLISH the horizontal centerline of the latch.
1a. HOLD the lock body to the inside of the door and POSITION it generally where
you would like it to mount.
1b. LOCATE the lock centerline notch on the latch and MARK this point on the inside
of the cabinet door using a pencil.
1c. DRAW the horizontal latch centerline from this mark on the inside of the cabinet
door and TRANSFER it to the outside of the cabinet door.
1d. TRANSFER this centerline to the inside of the cabinet or the second door on a
double-door cabinet.
1e. RECORD the MAC identification number for transfer to Aperio software.
1b
1c
1a
Latch centerline notch
Mounting the Lock
A
B
C
MAC identification
number on back side
D
3080076.004, Rev. B 6

2. TRANSFER the location of the inside wall of the cabinet to the door.
2a. MEASURE the horizontal distance between the inside edge of the cabinet and the door edge.
NOTE: The drawn line depicts the location of the strike mounting surface.
2b. DRAW a line on the outside surface of the door, using the same distance away from the door edge.
3. PLACE and USE the Lock/Reader Template.
NOTE: Orientation will be reversed for a right hand door.
3a. CUT through line to separate the Strike Plate Template.
3b. PEEL OFF the protective layer of the Lock Template, ALIGN it to both the latch
centerline and the line depicting the inside wall of cabinet, and PRESS to
secure.
NOTE: Two of the holes in the following step are 3/16” diameter and two are
1/2” diameter. The two pilot holes are 1/16”.
3c. DRILL four holes and two pilot holes through the cabinet, as shown
in the figure below.
3d. DRILL only one 3/16” hole depending on the desired
Antenna/Reader orientation.
3e. IF the optional Key Override will be installed,
THEN GO TO Step 5.
3f. REMOVE the lock template from the door.
Cabinet/door front view
Door edge
2a
2b
3a
3b, 3c, 3d
3080076.004, Rev. B 7

4. INSTALL the Shaft Extension.
4a. IF the cabinet door thickness is greater than ½”,
THEN INSTALL the Shaft Extension to the Antenna/Reader to ensure proper engagement into the lock.
4b. INSTALL the Shaft Extension to the shaft as shown
in the figure and firmly TIGHTEN the screw.
Door
Thickness Extension Shaft Used?
1/16” – ½” No
> ½” – 1 ½” Yes
5. IF a Cam Lock Key Override will be used, AND the orientation allows for
installation, THEN INSTALL the Key Override Paddle.
5a. INSERT the Paddle’s arm into the opening shown, and ALIGN the rails of the paddle to the ones on the
lock.
5b. SLIDE the paddle
gently until it stops.
6. PREPARE the Key Override Door.
NOTE: The Cam Lock is optional and must
be obtained by others.
6a. IF a Key Override is used,
THEN USE template to mark and drill a
hole for a 3/4” Cam Lock in the door.
Shaft Extension
2-56 X 1-¼” screw
(provided)
Table 1
5b
6a
6b. INSTALL the optional Cam Lock with
the cabinet lock as shown in the
figure.
6b
5a
3080076.004, Rev. B 8

7. INSTALL the Antenna/Reader.
***CAUTION***
Pinching the wires may prevent the Reader and
Lock from properly functioning.
7a. PLACE and HOLD the antenna/reader to the outside
of cabinet, routing the wire through the 1/2” offset
hole, and ENSURE the knob is in the locked position
in the vertical.
NOTE: Using the Table 2 below will help determine the
length of the top mount screw needed, based
on the thickness of the cabinet door.
7b. INSTALL the top mount screw to attach
the antenna/reader to the outside case.
8. INSTALL the lock.
8a. REMOVE the battery cover from lock.
8b. PLACE the lock on the inside of the door, threading the cable through the lock.
8b. ATTACH the lock to the antenna/reader using two 8-32 lock mount screws
(see Table 2 for length), and TIGHTEN the screws.
8c. INSTALL the two #6 self-threading screws and TIGHTEN.
NOTE: The third #6 self-threading screw is important to
achieve maximum holding force for doors greater
than 5/8” thick.
8d. INSTALL the third #6 self-threading screw only if the door
is more than 5/8” thick, using the lock as a guide, and
TIGHTEN.
Reader mounting screw.
7a
7b
Table 2
Cable is threaded
through the hole
in the lock.
8a
Used only for doors less
than 5/8” thick.
8b
8c
8d
3080076.004, Rev. B 9

9. Electrically CONNECT the antenna/reader wire to the lock body.
NOTE: The antenna/reader wire connector is keyed to only fit one way.
9a. ENSURE correct orientation of the connector while inserting it.
9b. TUCK excess cable into lock body as shown.
10. INSTALL the Batteries.
NOTE: New batteries should always be used and inserted in the
correct polarity position.
10a. INSTALL the battery and battery cover.
10b. INSTALL and TIGHTEN the screws.
11. PLACE the single-door Strike Plate Template.
11a. PEEL OFF the protective layer of the Strike Plate Template
and ALIGN it to both the latch centerline and the edge of
cabinet.
11b. DRILL two pilot holes as shown on template.
11c. REMOVE the template.
10a
10b
9a
9b
Connector cable tucked in
3080076.004, Rev. B 10