Asus RT-AC68U V4 User manual

RT-AC68U V4
Wireless-AC68U with AiMesh WiFi System
Quick Start Guide
A17951 / First Edition / March 2021

Table of Contents
English...................................................................................................................... 3
繁體中文 ................................................................................................................... 15
Bahasa Indonesia..................................................................................................... 27
Bahasa Melayu......................................................................................................... 39
ไทย ........................................................................................................................... 51
Tiếng Việt................................................................................................................... 63

3
English
1
Plug the adapter into the DC-IN port, and press the power button.
2
The Power, 2.4GHz/5GHz LEDs will light up when your hardware is ready.
Hardware Explanations
Button Explanations
LED Explanations
RESET BUTTON
Reset the system to its factory defaults.
WAN PORT
Connect your modem to this port with a network cable.
LAN PORTS 1-4
Connect your PC to a LAN port with a network cable.
WPS
button
Power
button
DCIN
port
USB 3.0/2.0 ports
WAN
port
LED On/Off
button
LAN ports 1-4
Reset
button
WiFi On/Off
button
LAN LEDs WAN
LED
USB 3.0
LED
2.4GHz
LED
5GHz
LED
Power
LED
USB 2.0 LED

4
English
Preparing to setup a standalone router
01
BEFORE SETTING
1
Go to ONE ROUTER SETUP STEPS.
ONE ROUTER SETUP
Preparing to setup an AiMesh
WiFi system
02
1
Two (2) ASUS routers (models supporting AiMesh https://www.asus.com/
AiMesh/).
2
Assign one as AiMesh router, and another one as AiMesh node.
** If you have multiple AiMesh routers, we recommend using the router with the highest
specifications as your AiMesh router and the others as AiMesh nodes.
3
Go to AiMesh SETUP STEPS.
AiMesh SETUP STEPS
AiMesh routerAiMesh node

5
ONE ROUTER SETUP STEPS
Prepare your Modem
01
1
Unplug the power of cable / DSL modem. If it
has a battery backup, remove the battery.
2
Connect your modem to the router with the
network cable provided.
3
Power on the modem. Plug modem to the
power outlet and power on.
WE SUGGEST...
Modem back
Modem back
English

6
4
Check the modem LED lights to ensure the
connection is active.
If you are using DSL for internet, you will need
your username / password from your Internet
service provider (ISP) to properly configure
your router.
Connect your Device
02
1
Power on the router.
Plug in and press the power button at the back of your router.
2
Check the WAN and 2.4GHz/5GHz LED lights to ensure the hardware connection
is ready.
Modem front
English

7
3
Connect your PC to the router using an additional network cable.
Login and Connect
03
1
Open a web browser.
You will be redirected to the ASUS Setup Wizard. If not, navigate to http://router.
asus.com.
English

8
AiMesh SETUP STEPS
Prepare
01
Place your AiMesh router and node within 3 meters of each other during the
setup process.
1
Refer to ONE ROUTER SETUP STEPS to connect your AiMesh router to your PC
and modem, and then log in into the web GUI.
AiMesh node
02
Factory default status. Keep power on and standby for AiMesh system settings.
AiMesh router
03
within
3 meters
AiMesh router
AiMesh node
AiMesh routerModem AiMesh node
Logout/Reboot
AiMesh Router
English

9
2
Go to Network Map page, click AiMesh icon and then Search for your extending
AiMesh node.
** If you cannot find the AiMesh icon here, click on firmware version and update the
firmware.
3
Click Search, it will automatically search for your AiMesh node. When the AiMesh
node shows on this page, click it to add it into the AiMesh system.
** If you cannot find any AiMesh node, please go to TROUBLE SHOOTING.
English

10
4
A message is displayed when synchronization is completed.
5
Congratulations! You will find the pages below show up when an AiMesh node
has been successfully added to the AiMesh network.
English
Successfully added RT-ABCDE to your AiMesh
system, it will take awhile to show up as connected
in the AiMesh router list.
OK

11
TROUBLESHOOTING
If your AiMesh router cannot find any AiMesh node nearby or synchronization
fails, please check followings and try again.
a
Move your AiMesh node closer to the AiMesh router ideally. Ensure it is within 3
meters.
b
Your AiMesh node is powered on.
c
Your AiMesh node is upgraded to AiMesh supported firmware.
i
Download AiMesh - supported fireware at: https://www.asus.com/AiMesh/
ii
Power on your AiMesh node and connect it to your PC via a network cable.
iii
Launch a web GUI. You will be redirected to the ASUS Setup Wizard. If not,
navigate to http://router.asus.com
iv
Go to Administration > Firmware Upgrade. Click on Choose File, and
upload the AiMesh-supported firmware.
v
After firmware uploaded, please go to Network Map page to confirm
whether AiMesh icon showed up.
English

12
vi
Press the reset button on your AiMesh node for at least 5 seconds. Release
the reset button when the power LED is flashing slowly.
English

13
RELOCATION
Locate AiMesh router and node at best place.
THE BEST PERFORMANCE
NOTES: To minimize interference, keep the routers away from devices like cordless phones,
Bluetooth devices and microwave ovens.
We recommend that you place the routers in an open or spacious location.
ASUS ROUTER APP
Download free ASUS Router APP to setup and manage your router(s).
English

14
FAQ FREQUENTLY ASKED QUESTIONS
Q1
Does the AiMesh router support Access Point mode?
A: Yes. You can choose to set the AiMesh router as router mode or
access point mode. Please go to web GUI (http://router.asus.com),
and go to the page Administration > Operation Mode.
Q2
Could I setup wired connection between AiMesh routers (Ethernet
backhaul)?
A: Yes. AiMesh system supports both wireless and wired connection
between AiMesh router and node to maximize throughput and
stability. AiMesh analyzes the wireless signal strength for each
frequency band available, and then determines automatically
whether a wireless or wired connection is best to serve as the inter-
router connection backbone.
1
Follow the setup steps to establish a connection between the AiMesh
router and node via WiFi first.
2
Place the node in the ideal locations for best coverage. Run an Ethernet
cable from the LAN port of the AiMesh router to the WAN port of AiMesh
node.
3
AiMesh system will auto-select the best path for data transmission,
whether wired or wireless.
English

15
繁體中文
1將電源變壓器插入無線路由器的電源插孔（DCIN），並按下電源按鈕。
2當您的路由器準備就緒後，電源指示燈、2.4GHz 和5GHz 指示燈將會亮起。
硬體說明
按鈕及插孔說明
LED 指示燈說明
重置按鈕
此按鈕可重置或回復系統至其初始設定。
WAN 連接埠
請使用網路線將您的數據機連接至此連接埠。
LAN 1-4 連接埠
請使用網路線將您的電腦連接至 LAN 連接埠。
WPS 按鈕 電源
開關
電源
插孔
USB 3.0 / 2.0 連接埠
WAN
連接埠 LED 指示燈 開啟 / 關閉
按鈕
LAN 1-4 連接埠
重置按鈕
Wi-Fi 開啟 /
關閉按鈕
LAN 指示燈 WAN（網際網路）
指示燈 USB 3.0 指示燈 2.4GHz 指示燈 5GHz 指示燈
電源指示燈
USB 2.0
指示燈

16
繁體中文
準備設定一台單獨的路由器
01
設定前
1請至 一台路由器的設定步驟 章節。
設定一台路由器
準備設定 AiMesh WiFi 系統
02
1準備兩台華碩無線路由器（欲瞭解支援 AiMesh 的華碩無線路由器型號，請參考
https://www.asus.com/tw/AiMesh/）。
2將一台路由器設定為 AiMesh 路由器，另一台設定為 AiMesh 節點。
** 若您有多台 AiMesh 路由器，建議您將擁有更高規格的路由器設定為 AiMesh 路由器，其他路由
器設定為 AiMesh 節點。
3請至 AiMesh 設定步驟 章節。
AiMesh 設定步驟
AiMesh 路由器AiMesh 節點

17
一台路由器的設定步驟
準備數據機
01
1拔除您的電纜/ DSL 數據機電源，
若數據機內含備用電池，請移除
電池。
2使用隨附的網路線連接您的數據機與無線
路由器。
3開啟數據機， 將數據機連接至電源插座
並開機。
建議您...
數據機後側
數據機後側
繁體中文

18
4檢查數據機上的 LED 指示燈，確認已經連線。
若您使用 DSL 連線網際網路，需要向您的網路
服務供應商（ISP）取得登入名稱 / 密碼，以正
確設定您的無線路由器。
連接您的裝置
02
1開啟路由器電源。
插入電源線並按下路由器後側的電源按鈕。
2檢查 WAN 和2.4GHz/5GHz 指示燈是否亮起以確認硬體連線是否準備就緒。
數據機正面
繁體中文

19
3使用另一條網路線連接您的電腦與無線路由器。
登入並連線網路
03
1開啟網頁瀏覽器。
您將進入 ASUS 設定精靈。若未出現此頁面，請手動輸入 http://router.asus.com。
繁體中文

20
AiMesh 設定步驟
準備
01
設定過程中，請將 AiMesh 節點距離 AiMesh 路由器 3 公尺內。
1請參照 一台路由器的設定步驟 章節連接您的 AiMesh 路由器和電腦、數據機，然
後登入網頁圖形使用者介面（web GUI）。
AiMesh 節點
02
原廠預設狀態。設定 AiMesh 系統時，請保持路由器處於通電及運作狀態。
AiMesh 路由器
03
3 公尺內
AiMesh 路由器
AiMesh 節點
AiMesh 路由器數據機 AiMesh 節點
登出 / 重啟
AiMesh 路由器
繁體中文