Asus (WL-330) User manual

English
Quick Start Guide
®
Pocket Wireless Access Point
(WL-330)
E1486
Copyright © 2003 ASUSTeK COMPUTER INC. All Rights Reserved.

2ASUS Pocket Wireless Access Point (WL-330)
English
Quick Start Guide
Package contents
Check the following items in your ASUS Pocket Wireless AP package. Contact
your retailer if any item is damaged or missing.
ASUS Pocket Wireless AP (WL-330)
Compact universal power adapter and plug (100V ~ 240V)
USB adapter and plug
RJ-45 connector and cable
Support CD
Quick Start Guide
Soft case
IMPORTANT! Use only the power adapter and plug that came with the
ASUS Pocket Wireless AP package. Using other power adapter and plug
may damage the device.
System requirements
Before installing the ASUS Pocket Wireless AP, make sure that your system
meets the following requirements:
•An Ethernet (10Base-T or 100Base-TX) adapter for wired client
•At least one 802.11b (11Mbps) or 802.11g (54Mbps) wireless adapter for
wireless mobile client
•An installed TCP/IP and Internet browser
NOTE. Refer to the User Guide in the support CD for detailed
information on the ASUS Pocket Wireless AP.

3ASUS Pocket Wireless Access Point (WL-330)
English
Quick Start Guide
Ethernet adapter mode (USB bus power)
1
3
42
1. Connect one end of the RJ-45
cable to the Ethernet port of the
device.
2. Connect the other end of the
RJ-45 cable to the Ethernet port
of your computer.
3. Insert the USB cable plug to the
DC-IN socket of the device.
4. Insert the other end of the USB
cable to any available USB port of
your computer.
After installation, check the Power and Ethernet LEDs. These LEDs light up to
indicate that the device is on and has physical connection to an Ethernet network.
NOTE. For notebooks with limited power supply, we recommend that you
use the supplied universal power adapter and plug instead of the USB
adapter and plug.
23
45
6
1
Installing the device
Follow these instructions to install the ASUS Pocket Wireless AP.
Access point mode (DC power)
1. Connect one end of the RJ-45 cable
to the Ethernet port of the device.
2. Connect the other end of the
RJ-45 cable to the 10Base-T port
of a network hub, switch, router, or
wall patch panel.
3. Insert the universal power adapter
plug to the DC-IN socket of the device.
4. Connect the universal power adapter to a
wall socket.
5. Insert the power plug to the DC-IN socket of the network hub, switch, or router.
6. Plug the power adapter of the network hub, switch, or router to a wall socket.

4ASUS Pocket Wireless Access Point (WL-330)
English
Quick Start Guide
LED indicators
The ASUS Pocket Wireless AP comes with a Power,
Wireless, and Ethernet LED indicators. Refer to the
table below for LED indications.
LED Status Mode* Indication
Power On AP/EA The device in on and ready.
Off AP/EA The device is off or performing boot sequence
Blinking AP/EA Firmware upgrade failed.
Wireless On AP The device is on and ready.
EA The device is associated with an AP or other
wireless device.
Off AP The device is off.
EA The device is not associated with an AP or other
wireless device.
Blinking AP/EA The device is transmitting or receiving data.
Ethernet On AP/EA The device is off or not connected to an Ethernet
network.
Off AP/EA The device is connected to an Ethernet network.
*Modes:
AP - Access point
EA - Ethernet adapter

5ASUS Pocket Wireless Access Point (WL-330)
English
Quick Start Guide
Installing the utilities
The support CD contains the utilities for configuring theASUS Pocket WirelessAP.
To install the device utilities in your computer:
1. Insert the support CD to the optical drive.
2. Click “Install ASUS WLAN AP Utilities”when the ASUS Wireless LAN
Access Point WL-330 installation window appears.
3. The device utilities are copied into your computer.
If Autorun is NOT enabled in your computer, browse the contents of the
support CD and double click the Setup.exe file to run the CD.
Other support CD options
Uninstall ASUS WLAN Card Utilities/Driver. Click this option to uninstall the
ASUS Pocket Wireless AP utilities from your system.
Run Setup Wizard Utility. Click this option to run the Setup Wizard utility.
Read/Install User Documentation. Click to view the installation and quick
setup guides in PDF format.
Explore this CD. Click this option to explore the support CD contents.
Browse our Web Site. Click this option to visit the ASUS website.
Click EXIT to close the installation window.

6ASUS Pocket Wireless Access Point (WL-330)
English
Quick Start Guide
Using the Setup Wizard utility
The Setup Wizard utility allows easy configuration of the ASUS Pocket Wireless
AP settings in both access point and Ethernet adapter modes. You may launch
the Setup Wizard utility directly from the support CD or from the Windows
®
desktop.
Launching the Setup Wizard utility
To launch the Setup Wizard utility
from the support CD:
1. Insert the support CD to the
optical drive.
2. Click the Run Setup Wizard
Utility option from the
installation window.
3. The Setup Wizard utility
window appears.
To launch the Setup Wizard from
the Windows
®
desktop:
1. Install the device utilities
following the steps in section 3.1.
2. From the Windows
®
desktop,
click Start > All Programs >
ASUS Utility > Wireless AP
WL-330 > Setup Wizard.
3. The Setup Wizard utility
window appears.

7ASUS Pocket Wireless Access Point (WL-330)
English
Quick Start Guide
Setting up your access point (AP mode)
To setup your access point (AP):
1. The Setup Wizard auto-detects
and displays the device SSID,
channel, encryption, MAC, and IP
addresses. Click Configure to
change these settings.
2. Enter the Network Name (SSID)
and channel you wish to use.
Click the WEP link or the
Encryption tab to set the WEP
encryption.
IMPORTANT! A wireless
client must have the same
SSID and WEP encryption
settings with the ASUS
Pocket Wireless AP to
establish connection.
3. Configure the AP WEP
encryption. Click OK when done.

8ASUS Pocket Wireless Access Point (WL-330)
English
Quick Start Guide
Connecting to an AP or other wireless devices (Ethernet
adapter mode)
The Setup Wizard utility also allows you to use your ASUS Pocket Wireless AP
as an Ethernet adapter that connects to an AP or other wireless device(s).
To connect the ASUS Pocket Wireless AP to an AP or wireless device(s):
1. Switch the ASUS Pocket Wireless AP to Ethernet adapter mode using the
mode switch on the bottom of the device.
2. From the Windows
®
desktop, click Start > All Programs > ASUS Utility >
Wireless AP WL-330 > Setup Wizard.
3. The Ethernet Adapter Status
window appears and displays the
auto-detected Ethernet adapter
settings. Click Configure to
connect to an AP or wireless
device (s).
NOTE. The available
networks are indicated by
icons for easy identification.
Refer to the icon indications
table in the User Guide for
details.
4. Select a wireless network from
the Available Networks list, then
click Configure.

9ASUS Pocket Wireless Access Point (WL-330)
English
Quick Start Guide
5. Enter the network name (SSID) of
the wireless network you wish to
connect.
6. Select the channel of the wireless
network you wish to connect.
10. Configure the Ethernet adapter
WEP encryption settings.
Click OK when done.
7. Set the Network Type.Select Infrastructure if you wish to connect to an
AP. Select Ad Hoc if you wish to connect to another wireless device.
8. Enable or disable MAC Cloning.
9. Click the WEP link or the Encryption tab.
NOTE. You may select the
channel if you set the
device in an Ad-hoc
network environment. In
Infrastructure network, the
channel is automatically
selected.
IMPORTANT! Change the
device WEP encryption
settings only when your
selected network has an
enabled WEP encryption.
•The SSID and WEP encryption keys of the ASUS Pocket Wireless AP
must be the same with that of the AP or wireless device to establish
connection.
•If you are trying to connect to an AP (Infrastructure), make sure the MAC
address of the ASUS Pocket Wireless AP is included in the AP
authorization table.

10 ASUS Pocket Wireless Access Point (WL-330)
English
Quick Start Guide
Web onfiguration utility
The Web Configuration utility allows you to configure theASUS Pocket Wireless
AP using a web browser on your computer. The following sections provide
information on how to launch this utility.
Launching the Web Configuration utility
To launch the Web Configuration utility using the Device Discovery utility:
1. Click Start > All Programs > ASUS Utility > Wireless AP WL-330 >
Device Discovery.
2. The Device Discovery window
appears.
3. Click Config to launch the Web
Configuration utility.
To launch the Web Configuration utility using a web browser:
1. Open a web browser.
2. Disable your web proxy, if you are using one.
3. Type http://192.168.1.1 on the address bar, then press <Enter>.
NOTE. This option requires you to change the TCP/IP settings of the
network adapter where the ASUS Pocket Wireless AP is connected.
Refer to the User Guide in the support CD for instructions on how to
change the TCP/IP configurations.