Atari RadiKal Bikers 33338 User manual

i
»
A.
ATA* I
G A IVI E S
JUNE 1998
16-30038-101
gaelco
DEDICATED GAME
OPERATION MANUAL
(for models 33338 and 36238)
Operation & Adjustments • Testing & Problem Diagnosis
Parts Information • Wiring Diagrams
TM
WARNINGS & NOTICES
WARNING
USE OF NON-ATARI PARTS OR CIRCUIT MODIFICATIONS MAY CAUSE SERIOUS INJURY OR EQUIPMENT
DAMAGE! USE ONLY ATARI AUTHORIZED PARTS.
*Substitute parts or modifications may void EMCdirective or FCC type acceptance.
* For safety and reliability, substitute parts and modifications are not recommended. Use only ATARI authorized
components and parts. Failure to do so will void warranty and may result in incorrect and/or unsafe operation.
*This game is protected by federal copyright, trademark and patent laws. Unauthorized modifications may be illegal
under federal law. This also applies to ATARI logos, designs, publications and assemblies. Moreover, facsimiles of
ATARI equipment (or any feature thereof) may be illegal under federal law, regardless of whether or not such
facsimiles are manufactured with ATARI components.
Look on our Website for more information, http: //www.atarigames.com

TABLE OF CONTENTS
Section One - Operation
Safety Notices/Epilepsy Warning 1-2
Product Specifications 1-3
Product Configuration 1-3
Inspection and Installation 1-4
Maintenance 1-5
Service 1-6
Control Panel Assembly Diagram 1-7
Handlebar Mechanism Diagram, Orientation 1-8
Handlebar Mechanism Diagram, Upper 1-9
Handlebar Mechanism Diagram, Lower 1-10
Cabinet Assembly Diagrams 1-13
Game Electronics Components 1-14
Linking 1-16
Game Operation 1-17
Starting Up 1-17
Game Rules 1-17
Player Controls 1-18
Operator Controls 1-19
Control Switch Location Diagram 1-19
Test Mode Menu System Operation 1-20
System Overview 1-20
Organization 1-20
Screen Adjustments 1-20
Input Tests 1-21
Game Assignments 1-22
Handle Adjust 1-23
Output Test 1-24
Book Keeping 1-25
Time Histogram 1-25
Game Statistics 1-26
Exit Menu 1-27

Section Two - Parts Information
Cabinet Front- View 2-2
Cabinet Rear View 2-3
Control Panel Assembly 2-4
Handlebar Mechanism -Upper 2-5
Handlebar Mechanism - Lower 2-6
Pushbutton Assembly 2-7
CPU Board Assembly 2-8
Electronics Assembly 2-9
Power Supply Diagram 2-9
Rear Door Locking Hasp Assembly 2-10
Rear Door Assembly 2-10
Coin Door Assembly 2-11
Line Cord Application Chart 2-12
Coin Door Application Chart 2-13
Section Three - Cabinet Wiring
Edge Connector Chart 3-2
Cabinet Wiring Diagram 3-3
Cabinet AC Wiring Diagram 3-4
CPU Board Assembly Diagram 3-5
Section Four - Troubleshooting
Game Does Not Start 4-2
Game Can Not Be Played 4-3
Control Problems 4-4
Linking Problems 4-5
Audio Problems 4-6
Video Problems 4-7
Miscellaneous 4-8
©Copyright 1998 ATARI Games Corporation. All rights reserved.

r
RADIKAL BIKERS
TM
OPERATION
SECTION
ONE
NOTICE
Information in this manual is subject to change without notice. ATARI reserves the right to make improvements in
equipment function, design, or components as progress inengineeringor manufacturing methods maywarrant.
Fill out and mail in the Game Registration card. Be sure to include the game serial number from the label on the
rear ofthe cabinet. Foryour records,
write the game serial number inthe manual. SERIAL NUMBER
THIS GAME USES ANON-STANDARD EDGE CONNECTOR AND WIRING. REPLACE THE WIRING
HARNESS ONL Y WITHAUTHORIZED PARTS. USING ANY OTHER PARTS CAN DAMAGE THE CPU
ASSEMBLY AND VOID THE WARRANTY!
1-1

SAFETY NOTICES
The following safety instructions apply to all game operators and service personnel. There are specific
warnings and cautionsthroughout this manual. Readthis page beforepreparing yourgame for play.
A
CAUTION
TRANSPORTING GAME. This game contains glass and fragile electronic devices. Transport this game
securely. Avoid rough handling when moving cabinet. Do not move this game with power on.
AC POWER CONNECTION. Verify that the switch on the power supply is set for 110VAC or 220VAC
according to local line voltage. Verify that the fluorescent lampassembly is correct for local line voltage.
PROPERLY GROUNDTHE GAME. To avoid electrical shocks, do not plug inthe game until ithas been
inspected and properly grounded. Thisgame should only be plugged into afixed-location grounded 3-wire
outlet. Do not use a"cheater" plug or cut off the ground pin on the line cord.
POTENTIAL SHOCK HAZARD. This video game system does not utilize an isolation transformer. There
is no isolation between the internal cabinet AC system and the external AC line.
DISCONNECT POWER DURING REPAIRS. To avoid electrical shock, turn off the power switch and
disconnect the game from the AC power source before removing or repairing any part of the game. After
servicing any parts of the
unit, be sure that allofthe ground wires are secure before restoring power.
PROPERLY ATTACH ALL CONNECTORS. Be sure that the connectors on each printed circuit board
(PCB) are properly connected. If theydo not slip on easily, do notforce them. A reversed connector may
damage your game and void the warranty. Connectors are keyed to fitspecific pins on each board.
USE PROPER FUSE. To avoid electrical shock, all replacement fuses must match the type, voltage
rating, and current rating of the original fuse.
HANDLE FLUORESCENT TUBE AND CRT WITH CARE. If you drop a fluorescent tube or CRT and it
breaks, it will implode! Shattered glass can fly eight feet or more from the implosion.
EPILEPSY WARNING
A very small portion of the population has a condition which may cause them to experience
epileptic seizures or have momentary loss of consciousness when viewing certain kinds of
flashing lights or patterns that are present in our daily environment. These persons may
experience seizures while watching some kinds of television pictures or playing certain video
games. People who have not had any previous seizures may nonetheless have an undetected
epileptic condition.
If you or anyone in your family has experienced symptoms linked to an epileptic condition (e.g.,
seizures or loss of awareness), immediately consult your physician before using any video games.
Parents should observe their children while they play video games. If you or your child
experience the following symptoms: dizziness, altered vision, eye or muscle twitching, involuntary
movements, loss of awareness, disorientation, or convulsions, DISCONTINUE USE IMMEDIATELY
and consult your physician.
1-2

r
PRODUCT SPECIFICATIONS
Operating Requirements
Location Electrical Power
Temperature
Humidity
Domestic 120VAC @ 60Hz 4.0 Amps
32°Fto 100°F
Not to exceed 95% relative
Foreign 230VAC @ 50Hz 2.0 Amps
(0°C to 38°C)
Japan 100VAC @ 50Hz 4.0 Amps
Cabinet Statistics
Shippinq Dimensions
Shippinq Weiqht
Desiqn Type
Width 32.0" (81.3 cm)
318 lbs. (140 kg.)
Single Dedicated Video
Depth 66.5" (169 cm)
Height 76.0" (193 cm)
Game with Linking capability
Equipment Characteristics
Video Display Monitor
Standard Resolution RGB
25" (68.6 cm) CRT
Game Characteristics
Player Variables
1 or 2 players (with Linking)
Choice of vehicle, track
Fastest Track Time Recognition
PRODUCT CONFIGURATION
Audio System
2 Channel Audio
2 Full Range Speakers
Operator Variables
Coinage, Play Mode,
Difficulty, Volume,
Audits, Statistics
Currency Acceptors
Standard Coin Door
2 Coin Mechanisms
1 Coin Counter
Diagnostics
Automatic Power-Up Test
Manual Menu System
♦ Stand Alone Units
Each game is ready to play right out of the box. Operators may use the menu screens in the game
menu system to determine some player variables in advance or leave the choices up to the players.
♦ Linked Units
Two unitscan be connected to allow players to compete against each other simultaneously,
a linkingcable supplied with each game.
1-3
There is

INSTALLATION AND INSPECTION
1. Remove all items from shipping containers andset aside. Inspect the exterior ofthe cabinet for any
signs of damage.
2. Remove the keys from the steering mechanism. Unlock and open the coin and cash box doors.
There are electrical cords and spare parts in the cash box.
3. Install one nut onto each leg leveler. Tilt the cabinet as needed to locate four threaded holes under
the cabinet. Install a leveler and nut into each hole. Do not tighten nuts at this time.
HASP
BRACKET
KEY LOCK
BRACKET
CABINET SHOWN FOR REFERENCE
A
WARNING
The cabinet is top heavy.
4. Stand cabinet uprightand make certain itis in a stable position. Move the game to its intended
location and
level the cabinet. This game is intendedfor use onlyina fixed position. Distribute weight
equally on each corner and tighten the leveler nuts.
5. Remove the rear door of cabinet. Inspect cabinet interior for any signs of damage. Check all major
assemblies to assure that they are mounted securely. Ensure that nothing blocks fan airflow.
6. An extra padlock may be installedto secure the rear door. A hasp is located in the spare parts bag.
Remove the two lock bracket nuts from inside the cabinet, above the rear door opening. Slide the
hasp onto the bolts so that it protrudes from the hole in back of the cabinet, then reinstall the nuts.
7. Modify the lock plate at the top of the rear door. Remove the bolts and nuts from the lock plate, then
rotate the plate so that the slot
will be above the door. Reinstall the bolts and nuts and tighten firmly.
CARRIAGE
BOLT
LOCK
PLATE
CARRIAGE
BOLT
HASP BRACKET AND LOCK PLATE ASSEMBLY INSTALLATION
1-4

The power cord is with the spare parts. Remove and save four screws from the line cord cover plate
at the rear of the cabinet. Match the holes on the IEC plug with the prongs in the receptacle and push
firmly to seat the line cord. Hold the cord flat against the cabinet and reinstall the cover plate (the
indentation should point down so that the cord exits toward the bottom of the cabinet).
(PART OF CABINET SHOWN
FOR REFERENCE ONLY)
SLINE CORD AND PLUG
LINE CORD INSTALLATION
9. Refer to the game's Cabinet WiringDiagram (Section Three of this manual) and check to see that all
cable connectors
are correctly secured. Inspect for damaged connectors. Be sure NOT TO FORCE
CONNECTORS and avoid making reversed connections.
10. Plug the game into a grounded (3-terminal) AC wall outlet. SwitchONthe game using the ON/OFF
switch located on the upper lefttop ofthe cabinet (when viewed from the player's position). The game
will power up and begin self-diagnostics. If no errors are found, the game will automatically enter its
"attract" mode of operation.
MAINTENANCE
♦ Viewing Glass
Use the T27 wrench to remove the ten tamper-resistant screws on the control panel cover. Pull the
control panel upward to expose the retaining strip. Remove the three screws holding the viewing
glass retaining strip in place. Slidethe glass upward slightly and swing it outward until it is free from
the cabinet. Movethe glass downward until it is free from the marquee.
♦ Cabinet
Use plastic-safe non-abrasivecleaners to avoid damage. Apply cleaner to a clean cloth or sponge,
then use this to wipe the decals orcabinet. Donot apply cleaner directly on artwork or cabinet!
♦ Controls
Use plastic-safe non-abrasive cleaners to avoid damaging the parts. Apply cleaner to a clean cloth or
sponge, then use itto wipe the controls clean. Do notapplycleaner directly to the controlsorcabinet!
1-5

SERVICE
Only qualified service personnel should perform maintenance and repairs. The product guidelines apply
to all game operators and service personnel. Specific notes, cautions, and warnings will be found
throughout this manual where they apply. Read the SAFETY pages thoroughly before beginning service.
This game uses complex electronic components that are very SENSITIVE to static electricity.
Observe and follow these precautions prior to handling the game electronics:
1. Ensure that the A.C. power to the game is turned OFF prior to servicing the electronics.
2. Discharge any static electricity build up in your body by touching the metal power supply
chassis. Do this BEFORE touching or handling the electronic assemblies.
3. Store the electronic assemblies in an anti-static area. Use anti-static bags to store or
transport the hard disk drive, the CPU Board Assembly, and all other electronics.
4. DO NOT remove or connect any electronic assemblies when the cabinet power is ON. This
will damage the electronic assemblies and void the warranty.
5.
Always replace ground wires, shields, covers, etc., after completing maintenance or service.
♦ Marquee
Remove the ten tamper-resistant screws holding the speaker grille to the marquee. Remove five hex-
head wood screws holding the marquee-retaining strip to the cabinet top. Hold the glass in place to
avoid breakage. Remove the retaining strip and set it aside. Lift the marquee glass out of the top
grooves and set in a safe place. Do not over tighten screws during re-installation.
A,
^WARNING
The marquee glass could fall out of the cabinet and break when the retaining strip is removed.
Fluorescent Lamp or Starter
Remove the marquee retaining strip, glass and artwork. Remove the fluorescent lamp locks. Grasp
the tube, give it a quarter turn and pull it from its socket. The starter also requires aquarter turn for
removal or installation. Carefully place a new tube into the socket and rotate it a quarter turn to
reinstall. Clean
the tube to remove fingerprints and dust.
A,
WARNING
If a fluorescent tube drops and breaks, it will implode and shatter glass! Use care in handling.
♦ Fluorescent Light Assembly
Remove the speaker grille, marquee retaining strip, glass, and artwork. Disconnect the power cable
from the fluorescent light
assembly. Loosen but do not remove the screws fastening the assembly to
the cabinet. Slide the assembly slightly forward to disengage the keyholes. Lift out the assembly.
♦ Control Panel
Use the T25 wrench to remove the four tamper-resistant screws at the control panel sides and six
tamper-resistant screws at either side of the handlebar protector. Pull the control panel upward to
expose the steering mechanism assembly, control buttons, and wiring harnesses. Before reinstalling
the control panel, ensure that harnesses and ground strap are reconnected.
1-6

A-22577 CONTROL PANEL ASSEMBLY
LEFT PLASTIC COVER
LEFT DECAL
LEFT PLATE
WOOD CONTROL PANEL
CONTROL PANEL HINGE
CONTROL PANEL HOUSING
FLANGEGR1P NUT 1/4-20 (4
CARRIAGE BOLT 1/4-20
1-7
HANDLEBAR MECHANISM
ASSEMBLY (UPPER)
RIGHT PLASTIC COVER
RIGHT DECAL
RIGHT PLATE
NOTE: LOWER HANDLEBAR MECHANISM
NOT SHOWN

♦ Handlebar Mechanism
Use the T25 wrenchto remove all ofthe tamper-resistant control panel mounting screws except the
six screws at the center holdingthe metal control panel plates to the mounting brackets. Pullthe
control panel upward enough to expose and the control wires. Label and disconnect the wires.
Support the mechanism and remove the remaining six mounting screws to free the mechanism from
the control panel plates.
Hold the mechanism and slide the plates to the side while lifting the
mechanism from the control panel. Place the mechanism on a workbench or other suitable surface
for repair.
While the steering mechanism is exposed, inspect the gears, switches, and cables. Install a new
hardware ifthe existing parts show signs of wear. Remember to calibrate after installation.
1ICR0SWITCH LEVERS
HANDLEBAR SHAFT MOUNTING NUT
CONTROL PANEL
SHOWN FOR REFERENCE
HANDLEBAR MECHANISM - ORIENTATION
1-8

HAND BRAKE CABLE
BRAKE CABLE END RETAINER
HAND BRAKE PROTECTOR
HAND BRAKE
HAND BRAKE NYLON STOPPER
HAND GRIP
UPPER HANDLEBAR COVER
ACCELERATOR CABLE
ACCELERATOR
HANDLE ASSEMBLY
HAND GRIP
LOWER HANDLEBAR COVER
UPPER HANDLEBAR PROTECTOR
LOWER HANDLEBAR PROTECTOR
HANDLEBAR MECHANISM - UPPER
1-9

>
z
D
r
m
>
m
m
o
</>
o
m
3D
BRAKE RECOVERY SPRING
MICROSWITCH
MICROSWITCH
SPRING
POTENTIOMETER GEAR
ARM SPRING
— RECOVERY SPRING, THROTTLE
MICROSWITCH LEVER
POTENTIOMETER
CENTRAL GEAR
SHAFT STOPPER
^®> ROCKER ARM
V^jP BEARING
END STOPPER

♦ Brake Cable
Remove the three T-20 tamper-resistant screws from the handlebar mechanism cover. Lift the cover
offthe steering mechanism and set itaside. Open the control panel. Separate the lower end of the
cable from the microswitch lever. Remove the microswitch lever retaining clip and pullthe lever from
its post. Rotate the lever to remove the barrel end of the cable. Disconnect the ball end of the cable
at the handle by pressing the underside of the cable retainer until the cable is loose. Pull the cable
from the handle by the sheath.
♦ Accelerator Cable
Remove the three T-20 tamper-resistant screws from the steering mechanism cover. Lift the cover off
the steering mechanism and
set itaside. Open the control panel. Separate the lower end of the cable
from the microswitch lever. Remove the microswitch lever retainingclipand pull the lever from its
post. Rotate the lever to remove the barrel end of the cable. Use an alien wrench to loosen the cover
ofthe accelerator cable retainer. Remove the barrel end of the cable from the accelerator grip.
♦ Handlebar Covers and Protectors
Open the control panel cover. Disconnect the accelerator and brake cables at the microswitch levers
only. Remove the nut at the handlebar shaft and the alien bolt holdingthe shaft to the handlebar.
Remove the handlebar offits shaft and lift itout of the control panel. The lower handlebar housing
and protectors are now free to remove.
♦ Accelerator Grip
Remove the upper handlebar cover. Remove the accelerator grip by carefully prying itfrom the
accelerator handle and pulling itaway. Disconnectthe accelerator cable by loosening the screw
holding the accelerator to the handlebar to expose the cable stop. Disconnect the cable from the
accelerator handle and pull the handle to remove itfrom the handlebar.
♦ Brake Handle and Grip
Removethe upper handlebar cover. Removethe handlebar grip bycarefully prying it from the
handlebar while pulling it away. Disconnect the ball end ofthe cable at the handle by pressing the
underside ofthe cable retainer until the cable is loose. Pull the cable from the handle bythe sheath.
Removethe handle
from the handlebar by loosening the alien bolt on the clip and sliding the handle
from the handlebar.
♦ Accelerator/Brake Switches
Open the control panel cover. Disconnect and label the switch wires. Use aflat-blade screwdriver to
removethe switch mounting screws. Replace switches only with ones ofthe same ratings.
♦ View/Start Buttons and Switches
Use the T25 wrenchto remove the ten tamper-resistant mounting screws from the controlpanel. Pull
the panel upward enough toexpose the switches. Label and disconnect wires. Gently bendthe large
prong of the holder just enough to slide the switch offthe pushbutton holder. Unscrew the nut from
the pushbutton housing and remove itfrom the control panel cover.
♦ Coin Meter
Switch off powerto the game. Unlock the cash door and swing itopen. Remove the cash tubs. The
meter is located on a plate at the vault bottom. Remove the screws and lift the plate just enough to
disconnect the meter wires from the harness. Record the meter count before testing or replacement.
♦ Coin Mechanism
Switch off powerto the game. Unlock the coindoorand swingitopen. Unlatch and remove each
coin mechanismseparately to clean or replace with a different type. Ensure that the mechanism
seats fully in the holder upon reinstallation. Close and lock the release latch, then close the door.
Turn onthe gameand changethe mechanism setup, thentest known good and bad coins to verify
operation.
1-11

Bill Validator
The game's wiring harness as manufactured does not support a separate bill validator connection,
although the coin door will accept such a mechanism. It may be possible to rework the wiring harness
to install a bill validator, but this has not been tested.
Monitor Bezel
Remove the dashboard and viewing glass. Grasp the monitor bezel at the bottom and lift it out of the
groove. Remove the bezel from the cabinet.
Monitor
Read these precautions thoroughlybefore beginning this procedure.
A
!> CAUTION
THE VIDEO MONITOR IS HEAVY, WITH MOST OF THE WEIGHT TOWARD THE FRONT OF THE
ASSEMBL Y. BE SURE IT IS FIRMLY SUPPORTED AS IT IS REMOVED FROM THE CABINET.
The monitor does not require isolation from the A.C. line voltage in normal operation.
However, when operating outside the cabinet or servicing the monitor on a test bench, YOU
MUST ISOLATE THE MONITOR FROM LINE VOLTAGE WITH AN ISOLATION TRANSFORMER.
♦ Speakers
NOTE: The speakers are magnetically shielded to prevent video monitor color impurity. Be
sure that any replacement speakers are also magnetically shielded.
Two 5.25" full range speakers are under the marquee. Remove the marquee, glass, and artwork.
Remove the speaker grille. The speakers come out from the outside of the cabinet. Be sure to
disconnect the cabling and remove the nuts on the mounting screws before attempting to remove the
speakers from the enclosure. Carefully reseat the seals upon completing any task in the speaker
enclosure. Refer to the Cabinet Wiring Diagram for correct speaker polarity.
1-12

CABINET ASSEMBLY DIAGRAM
FLUORESCENT LAMP ASSEMBLY
FLUORESCENT BULB, 15W 18"
5-1/2" SPEAKER, 8 OHM (2)
SPEAKER GRILL
HANDLEBAR ASSEMBLY
CONTROL PANEL ASSEMBLY
COIN DOOR ASSEMBLY
BLANK CASH DOOR
ON/OFF SWITCH
HANDLE PULL/VENT
CPU ASSEMBLY
REAR DOOR ASSEMBLY
LINE CORD COVER
1-13
SCREENED MARQUEE
MARQUEE GLASS, BLANK
MONITOR 25"
CRT GLASS
BEZEL 25"
SCREENED CABINET
LEG LEVELER
POWER SUPPLY

FAN ASSEMBLY
GAME ELECTRONICS COMPONENTS
CPU BOARD ASSEMBLY
A<
^CAUTION
THIS GAME USES AN EDGE CONNECTOR WITH NON-STANDARD WIRING. REPLACE THE
WIRING HARNESS ONLY WITH AUTHORIZED PARTS. USING ANY OTHER PARTS CAN
DAMAGE THE CPU ASSEMBLY AND VOID THE WARRANTY!
♦ CPU Board Assembly
Switch off power to the game. Unlock and remove the rear door. Carefully note the orientation of the
EDGE connector and the other cables. Extract the harness and other cables from the board
connectors. Remove the CPU Board Assembly mounting screws. Lift the board out of the cabinet and
set in a safe place. Anti-static bags and protective containers from new parts may be used for storage
if not to be reinstalled immediately.
♦ Memory Replacement
The ROM (Read Only Memory) circuits contain the computer operating instructions. Memory devices
are especially sensitive to static charges. Use grounding precautions when handling these parts.
Switch off power to the game. Unlock and remove the rear door. Remove the the CPU board assembly
from the cabinet wall. Set the CPU board assembly in a static-free work area and remove the cover.
Carefully note
each IC position, then remove using a chip extraction tool.
To reinstall memory circuits, orient a chip over its socket and press firmly to seat pins. Do not force.
A.
^CAUTION Discharge any static electricity build up in your body by touching the power
supply chassis. Do this BEFORE touching or handling the electronic assemblies.
1-14

♦ Power Supply
Switch off power to the game. Remove screws, then unlock and remove the rear door. Unplug the
IEC A.C. connector from the rear of the supply and the D.C. connector from the front. Remove two
front and two rear screws from the supply, then lift it off of the power chassis. Note voltage setting.
To reinstall the power supply,
set the voltage switch to the correct value. Set the supply on the power
chassis and align the mounting holes. Install the four screws and the two power connectors.
♦ Fan
Switch offpower to the game. Remove the cabinet rear door. Open the electronics assembly cover.
Disconnect the wiring harnesses, linking cable, and fan power connector from the circuit board. Remove
the circuit boards from the electronics assembly box. Remove the four nuts holding the fan to the
electronics assembly box.
1-15

LINKING
INTERCONNECTING GAMES
1. Verify the operation of the existing games before making any changes. Unlockthe coin doors of both
cabinets and press the TEST
MODE switches. Check the VERSION information displayed on the first
screen at the bottom. Both cabinets must have the same version number. Linking games with
different versions may cause games to halt or reset at random.
2. Turn OFF the power for both cabinets. Unlock and remove the cabinet rear doors. Find the linking
cable. It is shipped with the spare parts.
3. The linking cable connectors are keyed to fit one way. Orient the linking cable end plug over the right
side LINKS CONNECTOR socket (nearest the POWER connector) on the Electronics Assembly. "
Mate the connectors and press firmlyto seat fully. Do not use excessive force.
4. Route the cable through the cabinet interior and out of the slot or notch. Route the free end of the
cable through the slot or notch in the second cabinet and attach it to the electronics as above.
5. Turn ON the power for both cabinets. The games will start up and begin the Power On tests. Ifno
serious errors are detected, the games will enter the "attract" mode automatically If there are errors
reported on the screen, refer to Troubleshooting in Section Four for assistance.
6. Press the TEST MODE switches to enter the menu systems. Press the VIEW button to scroll through
the menu screens to the GAME ASSIGNMENTS screen. Select LINK TYPE, then choose MASTER
for one cabinet, and SLAVE for the other. Each machine must have adistinct LINK TYPE setting.
Use the brake handle to go to the DIFFICULTY setting. Both machines must have the same
DIFFICULTY setting. Do not turnoff the power oryour changes will be lost.
7. Press VIEW to scroll through the menu screens to the EXIT MENU and use the brake handle to select
EXIT AND SAVE CHANGES.
8. Both machines will reset. The games will start up and begin the Power On tests. If no errors are
detected, the games will enter the "attract" mode automatically and synchronize quickly.
9. Retract any excess cable back into the cabinets so that the cables do not touch the floor. This keeps
the cables away from the casters during relocation and protects it somewhat from player's feet.
Reinstall the rear doors onto the cabinets. Lock the rear doors and remove the key. Install screws at
the top and sides of the rear doors and tighten snugly. Close and lock the cash box and coin doors.
10. If
the cabinets need to be separated for service or relocation, enter the menu systems and return the
LINKTYPE setting to NO LINK for both game cabinets. Make sure to save these changes before you
disconnect the cable. Do not turnoff the power priorto saving the changes or they will be lost.
o
gaelcam
r ()
o
5
j-M-dilfcil
o
STEERS
pN
o
ij
PCB(ONNfCIOR
O C
LINKS CONNSCIOK
O
POWER
LOCATION OF CONNECTOR FOR LINKING CABLE
1-16
">

GAME OPERATION
STARTING UP
Each time the game is first turned on or power is restored, it begins executing code out of the boot ROM.
These self-diagnostic tests automatically verify and report the condition of the hardware. The screen
displays information about the software version and condition of the hardware. If any of the individual
tests fails, then an error message will be displayed for each test.
* If no buttons are pressed, the system will quickly complete alltests then load and run the game.
*Press and holdthe coin door TEST button to activate the TEST MODE menu system.
Once all Power-up tests have been passed, the game goes into its "attract mode." Scenes and sounds
from a typical game are alternated with previous high scores in an endless pattern until game playstarts.
Insertcurrencyto start the game. Playbegins after a
circuit is chosen. The game will progress until time
is exhausted. The game automaticallyreturns to the "attract mode" when playends.
GAME RULES
The game involves a pizza delivery biker who rides through the city in competition with another driver while
avoiding obstacles and other vehicles. Players can choose from several biker personalities and circuits.
Each circuit has fourstages: three pizzadeliveries and the returnto the pizzeria. The object of the game
is to complete
all of the deliveries and return to the pizzeria in the shortest time possible. There are time,
speed, and point bonuses throughout the course.
Players competeagainst drone delivery bikers or other players. Players who finish one ofthe four stages
of a circuitautomatically advance to the next stage.
INDIVIDUAL PLAY
Insert currency ortokens tostart the game. Press the START button. At the CHOOSE A RIDE message,
move the handlebars to the desired circuit and select it with the START button. Each circuit has a
particular difficulty level: EASY (Margherita), MEDIUM (Capricciosa), or HARD (Diabola). At the message
CHOOSE A BIKER, select a character with the handlebars and press the START button to begin game
play.
The competition begins automatically as bikers roll outof the pizzeria onto the circuit. During the race,
players must pass several CHECKPOINTS and collect bonuses to successfully complete the pizza run.
The more bonuses collected during the run, the faster the playerfinishesthe stage.
MULTIPLE PLAYERS
Two players on linked cabinets can compete head-to-head. Thegame begins as in individual play with the
selection of a circuit and a biker. When both players have completed their selections, the bikers leave
their respective pizzerias and competition begins. An indicator bar at the top of the screen shows which
player is scoring more points during competition.
STATISTICS
An on-screen displaycontinually updates status information forthe player:
Score is the player's present overall score.
Best lap isthe fastest time in which any player has ever completed the present circuit. That player's
initials appear next to the time in minutes and seconds.
Lap time is the elapsed time for the current player.
XJeft indicates the time remaining to complete the circuit.
Rev counter is the RPM of the scooter's motor.
Speedometer shows the current scooter speed.
Icon showsthe player's current position and indicates whether the competitor is a drone ("CPU") or a
linked cabinet ("1UP/2UP").
1-17