Atlantic Furniture COLUMBIA BUNK BED User manual

Size of Mattress and Foundation
The length and width of the upper and lower bunk mattress and foundation are as follows :
Width
37 ½”- 38 ½”
52”- 53”
LengthSize
74”- 75”
74”- 75”
Twin
Full
Thickness
9 ½” max
9 ½” max
You must use only this size mattress.
Ensure thickness of upper and lower mattress and foundation combined does not exceed 9 ½”
and that the mattress is at least 5” below upper edge of guardrails.
This Bunk Bed uses a slat kit for mattress foundation.
Replacement Parts
Replacement parts, including additional guardrails, may be obtained from any
Atlantic Furniture dealer
SAFETY WARNINGS
! !
( 1 )
( 2 )
( 3 )
( 4 )
( 5 )
( 6 )
( 7 )
( 8 )
( 9 )
(10)
(11)
(12)
(13)
Follow the information on the warnings appearing on the upper bunk end structure
and on the carton. Do not remove warning label from bed.
Always use the recommended size mattresses or mattress support, or both,
to help prevent the likehood of entrapment or falls.
Surface of mattress must be at least 5 in. (127mm) below the upper edge of guardrails.
Do not allow children under 6 years of age to use the upper bunk.
Periodically check and ensure that the guardrail, ladder, and other component are
in their proper position, free from damage, and that all connectors are tight.
Do not allow horseplay on or under the bed and prohibit jumping on the bed.
Always use ladder for entering or leaving upper bunk.
Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
Use of a night light may provide added safety precaution for a child using the upper bunk.
Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed
next to the wall, the guardrail that runs the full length of the bed should be placed against
the wall to prevent entrapment between the bed and the wall.
The use of water or sleep flotation mattresses is prohibited.
STRANGULATION HAZARD : Never attach or hang items to any part of the bunk bed
that are not designed for use with the bed; for example, but not limited to, hooks, belts
and jump ropes.
Keep these instructions for future reference.
Page 1 of 8
BUNK SAFETY WARNING

READY
ASSEMBLY INSTRUCTIONS
Before assembling your Columbia bunk bed, please read through these
Thank you for choosing Atlantic’s Bunk Bed.
This practical design offers the utmost in versatility.
(TWIN - TWIN) (TWIN - FULL) (FULL - FULL)
Adult Assembly
Allen wrench
Phillips head
Customer Supplied
screwdriver
instructions carefully. Familiarize yourself with the different parts.
Please note that you will require a Phillips head screwdriver and an Allen wrench.
COLUMBIA BUNK BED
GUARDRAIL CAN BE SET UP AT EITHER
END OF THE BUNK BED
COLUMBIA BUNK BED Page 2 of 8
TWIN / TWIN FULL / FULL
E
E
TWIN OVER FULL SHOWN
HARDWARE
AJCB M6 X 3 ½”(90mm) - 16 pcs
Spare - 2 pcs
BJCB M6 X 2”(50mm) - 4 pcs
Spare - 2 pcs
CBarrel Nut - 20 pcs
Spare - 2 pcs
1 ” Wood Screw - 4 pcs
Spare - 2 pcs
Spare - 1 pc
E
E
GAllen wrench - 1 pc
Spare - 1 pc
E
F
D
Metal Pins - 4 pcs
Wood Button - 8 pcs
NOTE: WE INCLUDE SPARE HARDWARE IN CASE THE ALLEN WRENCH, JCB, BARREL NUT, WOOD SCREW OR WOOD BUTTON ARE DAMAGED DURING ASSEMBLY.
ATTENTION! If you receive a damaged or defective item,
please contact Atlantic Furniture at [email protected] 1-800-955-3726 / M-F 9:00-5:00 EST

PARTS LIST
Page 3 of 8
01
02
03
04
05
06
07
08
09
10
HARDWARE
UPPER PANEL
LOWER PANEL
FULL GUARD RAIL
3/4 GUARD RAIL
LEFT END CAPS
RIGHT END CAPS
LONG RAIL
1 BOX
1 BOX
1 BOX
TWIN SLAT KIT
FULL UPPER BUNK SLAT KIT
FULL LOWER BUNK SLAT KIT
OR
OR
TWIN LOWER BUNK SLAT KIT
1 BOX
1 BOX
1 BOX
1 BOX
02
02
06
08
08
08
08
07
07
06
03
03
04
05
09
10
01
TWIN OVER FULL SHOWN
COLUMBIA BUNK BED

STEP 1
STEP 2
Adult Assembly
A
C
G
JCB M6 X 3 ½”
Barrel Nut
Allen wrench
Page 4 of 8
02
02
08
08
A
A
B
B
B
B
A
C
C
C
C
05
06
06
07
07
04
Attach the long rails (08) to the upper panels (02), using JCB M6 X 3 ½” (A), and barrel nut (C).
Tighten with the Allen wrench (G).
Attach the full guard rail (04) to the end caps (06)(07), using JCB M6 X 2” (B),
and barrel nut (C). Tighten with the Allen wrench (G).
Repeat for 3/4 guard rail (05).
If the bunk bed will be placed next to a wall, the guard rail that runs the full length of the bed
should be placed against the wall to prevent entrapment between the bed and the wall.
Note : Screw holes on end caps
go on inside of guard rails.
B
C
G
Adult Assembly
JCB M6 X 2 ”
Barrel Nut
Allen wrench
C
C
C
C
COLUMBIA BUNK BED

Page 5 of 8
STEP 3
STEP 4
Adult Assembly
Phillips head
Customer Supplied
screwdriver
Lay the twin slat kit (09) onto the bed. Fix in place using wood screws provided in the slat kit box.
FOR SLAT KIT ASSEMBLY follow assembly instructions included with slat kit.
Twin size shown
Full Upper panel uses Full upper slat kit
Install the full and 3/4 guard rail assemblies onto the long rails, and fix in place using wood
screws (D). Tighten with the Phillips head screwdriver.(Customer Supplied)
Adult Assembly
1 “ Wood Screw
Phillips head
Customer Supplied
screwdriver
D
FULL GUARD RAIL
ASSEMBLY
3/4 GUARD RAIL
COLUMBIA BUNK BED
D
D
D
D
09
GUARDRAIL CAN BE SET UP AT EITHER
END OF THE BUNK BED

STEP 5
STEP 6
Page 6 of 8
Adult Assembly
A
C
G
JCB M6 X 3 ½”
Barrel Nut
Allen wrench
Attach the long rails (08) to the lower panel (03), using JCB M6 X 3 ½” (A), and barrel nut (C).
Tighten with the Allen wrench (G).
A
C
C
C
C
A
A
A
08
03
03
08
Lay the slat kit with center support (10) onto the bed, and fix in place using wood screws
provided in the slat kit box. FOR SLAT KIT ASSEMBLY follow assembly instuctions included
with slat kit.
Adult Assembly
Phillips head
Customer Supplied
screwdriver
Full size shown
Twin lower panel uses Twin slat kit
10
COLUMBIA BUNK BED

STEP 7
Page 7 of 8
Adult Assembly
Metal Pins
Wood Button
E
F
Insert metal pins (E) into the holes in top of the lower panels. Lift the upper panels onto the
lower panels as shown, and fit the metal pins into the holes in the bottom of the upper panel legs.
This step requires
two strong people.
This step requires
two strong people.
CAUTION
!
TWIN-FULL
TWIN-TWIN
FULL-FULL
Congratulations !
Your Columbia bunk bed is now ready for use.
We recommend that you double check that all screws are tight,
and that all parts are secure before use and periodically check that all screws are tight to ensure lasting Safety.
Adult Assembly
Phillips head
Customer Supplied
screwdriver
FOR LADDER ASSEMBLY, PLEASE
FOLLOW ASSEMBLY INSTRUCTIONS
INCLUDED WITH YOUR LADDER.
Lastly, install Ladder.
STEP 8
Cover holes with wood buttons (F)(Twin Full, Full Full ).
F
E
E
E
F
F
COLUMBIA BUNK BED
TWIN OVER FULL SHOWN

STEP 9
STEP 10
Disassemble upper bunk by removing guard rails. Also remove metal pin from lower bunk.
Disassemble upper bunk by removing upper panel (02) and lower bunk by removing lower panel(03).
Exchange upper panel to the lower panel position and Install hardware tighten with Allen wrench.
UPPER BUNK
UPPER BUNK
LOWER BUNK
LOWER BUNK
CONVERSION TO 2 TWIN OR 2 FULL BEDS.
TWO TWIN BEDS
TWO FULL BEDS
Use Wood button (F)
to cover holes as shown.
F
F
F
F
F
F
F
F
F
F
F
F
Page 8 of 8
02
03
Metal Pin
COLUMBIA BUNK BED