Atlantic Coda 38408143 User manual

Item#: 38408143
Coda Rattan Bar Cabinet
Ver. 01 01/27/21
Customer Service:
800-747-2660

1
Assembly Tips:
Become familiar with the instructions and all parts.
Make sure that all parts are in the box and in good condition.
Assemble the product on the open flat carton or a rug to protect the product and
your floor.
Some heavy products need a second person to assist in the assembly.
Use of power tools is not recommended.
Consejos para armar:
Familiarícese con las instrucciones y todas las piezas.
Asegúrese de que todas las partes estén en la caja y en buenas condiciones.
Arme el producto sobre la caja de cartón plana abierta o una alfombra para proteger el
producto y su piso.
Algunos productos pesados necesitan una segunda persona para ayudar a armarlos.
No se recomienda el uso de herramientas eléctricas.
Caution:
Never let children climb on furniture or play with furniture. Use provided wall anchors.
Use care when moving furniture. Furniture can tip over if moved improperly.
!
!
Do not place a weight heavier than the recommended load rating on the furniture surface.
Do not install on sloping surface.
Improper handling can result in cuts and lacerations.
Precaución:
Nunca deje que los niños suban sobre muebles o jueguen con los muebles.
No coloque un peso que sea más pesado que la capacidad de carga
recomendada en la superficie del mueble. Utilice los anclajes de pared suministrados.
Tenga cuidado al mover muebles.
Los muebles pueden caerse si se mueven de manera incorrecta.
No instale en una superficie en pendiente.
Care Instructions:
Use electrostatic dust cloths to clean furniture. Do not set hot or cold containers directly on the
furniture surface.
Instrucciones para el cuidado:
Utilice paños de polvo electrostáticos para limpiar los muebles. No coloque recipientes calientes
o fríos directamente sobre la superficie de los muebles.

2
Parts List/ Lista de Piezas
Tools Needed (not included) Herramanientas requeridas
(no incluidas)
Ø3mm (Ø1/8”)
Ø4.5mm (Ø3/16”)
11 12
12
12
13
14
1
2
10
10
3
45
6
7
8
7
9
10
10

Screw in cam screws (A) into panel (1) with Philips screwdriver.
Screw in glass rack (L) into panel (1) with screws (D) using
Philips screwdriver.
Screw in magnetes (M into panel (1) with screws (G) using
Philips screwdriver.
Screw in door hinge with pins (N) into panels (13) & (14)
with screws (D) using Philips screwdriver.
Then screw in metal plate (O) into panels (13) & (14)
with screws (D) using Philips screwdriver.
1
2
3
1
13 14

3
4
4
Screw in cam screws (A) into panels (2) & (6) using
Philips screwdriver.
Screw in cam screws (A) into panel (4) using Philips
screwdriver. Then flip panel over and screw in cam
screws (A) into panel (4) using Philips screwdriver.
2
6
4
4
5
4
Combine panels (4) and (6) panel (5) with wood dowels
(C) and cam screws from panels (4 and (6). Insert cam
locks (B) into panel (5) and turn clockwise to lock in place
with Philips screwdriver.

5
6
5
3
2
Attach panel (3) to pre-assembled part from step 4 and
panel (2) with wood dowels (C) and cam screws from panel
(2) and pre-assembled part from step (4). Insert cam locks
(B) into panel (3) and turn clockwise to lock in place with
Phillips screwdriver.
9
Take pre-assembled part from step 5 and attach panel (9)
with wood dowels (C) and screws (E) using Philips screwdrive.r

7
8
6
7
Take pre-assembled part from step 6 and slide panel (7)
into the back channel to the bottom of pre-assembled part.
Insert channel support bracket (8) onto back panel (6). Then
slide panel (7) into channel support bracket (8).
8
7
7

9
10
7
1
13
14
Attach panel (1) to pre-assembled part from step 8 with wood dowels (C)
and cam screws from panel (1). Inside cabinet, insert cam locks (B) and
screw counter clockwise with Phillips screwdriver to lock in place.
Attach door panels (13 and (14) by inserting hinge pins into pre-drilled
holes.
Attach door knobs (H) with screws (J) using
Phillips screwdriver.

11
12
8
Gently Flip over pre-assembled part from step 10 and
attach leg brackets (I) to bottom of pre-assembled part
with screws (F) using Philips screwdriver. Attach legs (10)
by screwing clockwise. Then place pads (P) on bottom legs.
On bottom back panel, take screw (F) using Phillips screwdriver
screw into back panel. Attach 8 support brackets (G) and screw
onto edges of back panels of cabinet with Phillips screwdriver.
Safety Option: Place straps (T) on top back inside edge with
washers (S) and and screws (2) with Phillips screwdriver.

13
9
Safety Option: Use stud finder to find stud. Drill
holes with drill bit (1/8" stud or 3/16" anchor). For
wall anchors (R) into wall. Take screws (E), washers
(S),and insert into straps and screw in anchor with
Phillips screw driver. For stud, take screws (E),
washers (s), and insert into straps and screw in stud
with Phillips screw driver.
Product Warranty
Thank you for your Atlantic Inc. purchase. This Limited Warranty covers any defects in material or workmanship for purchases made in the
U.S.A and Canada, and excludes claims from conditions, malfunctions or damage not resulting from defects in material or workmanship. The
warranty duration is one year. Keep your original proof of purchase (store receipt). If after inspection you find the product is dfective or missing
parts, DO NOT return to store. Please contact customer service at [phone] M-TH, 8am-5pm; Fri, 8am-12pm (pacific Time) or email
[email protected]. Keep maual for future reference.
Garantia de Producto
Gracias por su compra de Atlantic Inc. Esta Garantía a Limitada cubre cualquier defecto en
material o fabicación para compras en EE.UU y Canadá, y excluye reclamaciones de condiciones,
mal funcionamiento o daños no resultantes de defectos en material o fabricación. La duración de
la garantía es de un año. Guarde su prueba de compra original (recibo el la tienda). Si depués de
la inspección usted encuentra que el producto es defectuoso, está dañado o le faltan partes, NO lo
devuelva a la tienda. Por favor pongase en contacto con el servico al cliente al [phone] de
lunes a jueves, de 8am a 5pm; viemes, de 8am a 12pm (Hora del Pacifico). O envíe correo
electrónico a [email protected]. Por favor guarde este Manual de instrucciones
para futura referencia.
Made in China / Hecho en China
©2021 ATLANTIC INC.
All rights reserved / Derechos Reservados
Customer Service/ Servicio al cliente
PO Box 2399
Santa Fe Springs, CA 90670 USA
1-800-747-2660
[email protected]
www.theatlanticstore.com
Ø3mm (Ø1/8”)
Ø4.5mm (Ø3/16”)
11
12
12
12
Insert panels (12) into panel (11). Then insert it into
right side of cabinet.