Atmel AVR ATICE10 User manual

ATICE10
.............................................................................
User Guide

AVR ATICE10 User Guide i
Table of Contents
Section 1
Introduction ........................................................................................... 1-1
1.1 About this Manual .....................................................................................1-1
1.2 General Description ..................................................................................1-1
1.3 ICE10 Features .........................................................................................1-1
1.4 ICE10 Contents.........................................................................................1-2
1.5 System Requirements...............................................................................1-2
1.5.1 Hardware Requirements.....................................................................1-2
1.5.2 Software Requirements ......................................................................1-2
1.5.3 Operating Conditions..........................................................................1-2
1.5.4 Host Interface .....................................................................................1-2
Section 2
Preparing the ICE10 System for Use.................................................... 2-1
2.1 General Hardware Description..................................................................2-1
2.2 Connecting ICE10 to PC ...........................................................................2-3
2.3 Connecting ICE10 to Target Board...........................................................2-3
2.4 Jumper Settings ........................................................................................2-3
2.5 Connecting Power.....................................................................................2-3
2.6 Summary...................................................................................................2-3
Section 3
Using the ICE10.................................................................................... 3-1
3.1 Installing AVR Studio ................................................................................3-1
3.2 Emulating with ICE10................................................................................3-1
3.2.1 Initial Setup.........................................................................................3-1
3.2.2 Starting AVR Studio............................................................................3-1
3.3 ICE10 Emulator Options ...........................................................................3-1
3.3.1 Device.................................................................................................3-2
3.3.2 Clock Source ......................................................................................3-2
3.3.3 Internal Frequency..............................................................................3-2
3.3.4 External Range...................................................................................3-2
3.4 Emulator Configuration System ................................................................3-2
3.5 Using Breakpoint.......................................................................................3-3
3.6 Using Traces.............................................................................................3-3
3.7 Using Triggers...........................................................................................3-3
3.8 Logic Analyzer ..........................................................................................3-4

Table of Contents
ii AVR ATICE10 User Guide
Section 4
AT90ADCPOD Configuration ............................................................... 4-1
4.1 Introduction ...............................................................................................4-1
4.2 Configuring the AT90ADCPOD.................................................................4-2
4.3 The ICE10 Power System.........................................................................4-3
4.3.1 The Target Applications Power Requirements ...................................4-3
4.4 The ICE10 Clock System..........................................................................4-4
4.4.1 The Timer Oscillator ...........................................................................4-5
4.5 The Analog Comparator............................................................................4-5
4.5.1 Connectors not Described in this User Guide ....................................4-5
4.6 Jumper Settings Reference Table ............................................................4-5
Section 5
Hardware Description ........................................................................... 5-1
5.1 Front Panel ...............................................................................................5-1
5.1.1 Status LEDs........................................................................................5-1
5.1.2 Logic Analyzer Connectors.................................................................5-1
5.1.3 AUX Connector...................................................................................5-1
5.1.4 POD Connector ..................................................................................5-1
5.2 Back Panel................................................................................................5-1
5.2.1 Serial Number.....................................................................................5-1
5.2.2 Serial Port RS232 C ...........................................................................5-1
5.2.3 Parallel Port ........................................................................................5-1
5.2.4 AVR Prog. Connector .........................................................................5-1
5.2.5 AVR Reset Button ..............................................................................5-2
5.2.6 ICE Reset Button................................................................................5-2
5.2.7 ON-OFF Switch ..................................................................................5-2
5.2.8 12V DC Connector .............................................................................5-2
5.3 Power System ...........................................................................................5-2
5.4 Reset System............................................................................................5-2
Section 6
Special Considerations ......................................................................... 6-1
6.1 Stack .........................................................................................................6-1
6.2 Assembling ...............................................................................................6-1
6.3 ADC ..........................................................................................................6-1
6.4 Noise Canceler Mode ...............................................................................6-2
6.5 Timer/Counter1 .........................................................................................6-2
6.6 Analog Comparator...................................................................................6-2

Table of Contents
AVR ATICE10 User Guide iii
Section 7
Troubleshooting Guide ......................................................................... 7-1
Section 8
Technical Specifications ....................................................................... 8-1

Table of Contents
iv AVR ATICE10 User Guide

AVR®ATICE10 User Guide 1-1
Section 1
Introduction
Figure 1-1. ATICE10
Congratulations on your purchase of the ATICE10 AVR®In-Circuit Emulator (ICE).
ICE10™is a high-end emulator designed to provide a complete, and easy to use, devel-
opment and debug environment for the AVR Flash microcontrollers from Atmel
Corporation.
1.1 About this
Manual
This user guide serves as a reference manual for the Atmel AVR ICE10 in-circuit emula-
tor. The AVR ICE10 User Guide is an easy introduction on how to use the ICE10, and a
detailed reference for advanced users. Throughout the manual, many references to the
AVR microcontrollers are made in short form, i.e. AT90S2313 is referred to as S2313
and so on.
1.2 General
Description
The Atmel AVR ICE10 is a real-time in-circuit emulator for a wide range of AVR devices.
The ICE10 is controlled by AVR Studio®, version 3.5 or later.
1.3 ICE10 Features  Devices Supported: ATtiny11, ATtiny12, ATtiny15, ATtiny22, ATtiny28 AT90S1200,
AT90S2313, AT90S/LS2323, AT90S/LS2343, AT90S/LS2333, AT90S/LS4433,
AT90S4414, AT90S8515, AT90S/LS4434, AT90S/LS8535
 Emulates all On-Chip Functions, both Digital and Analog
 Trace Buffer (32K x 96-bit)
Rev. 1632B-09/01

Introduction
1-2 AVR®ATICE10 User Guide
 Unlimited Number of Breakpoints
 Full Visibility of and Access to Register File, SP, PC and Memories
 Access to all I/O Registers
 Logic Analyzer Interface Output
 Supports Assembler and C Source Level Debugging
 5 Trigger Outputs
 5 Trigger Inputs
 Internal and External Clock Options
 External Data Memory Emulation
 2.7 - 6.0V Operating Voltage
 Software Upgradable for Future AVR Devices
1.4 ICE10 Contents The ATICE10 Contains the Following Items:
 ICE10 In-Circuit Emulator Unit
 Pod Card ATtiny15POD with Cables
 Pod Card AT90ADCPOD with Cables
 RS-232 Cable
 Universal Voltage Power Supply (100 - 240V, 50 - 60 Hz)
 American Power Cable
 European Power Cable
 Atmel CD-ROM Containing Software
 ATICE10 User Guide
 Warning Note
1.5 System
Requirements
For the ICE10 to operate correctly and trouble free, the following software and hardware
requirements should be met.
1.5.1 Hardware
Requirements
Pentium-class personal computer with:
 32 MB RAM
 20 MB free hard disk space
 CD-ROM or Internet access (for software and databooks)
 VGA monitor
 19200 bps RS-232 port (COM port)
1.5.2 Software
Requirements
The following operating systems are currently supported by AVR Studio:
 Windows®95
 Windows 98 (SE) (ME)
 Windows NT®3.51
 Windows NT 4.0
 Windows 2000
1.5.3 Operating
Conditions
 Operation Temperature: 0oC - 70oC
 Operating Humidity: 10 - 90% RH (non-condensing)

Introduction
AVR®ATICE10 User Guide 1-3
1.5.4 Host Interface  RS-232C @ 19200 bps, N81
 9-pin female connector

Introduction
1-4 AVR®ATICE10 User Guide