Audiovox Vme 9309ts User manual

VME 9309TS

Thank you for choosing a Audiovox product. We hope you will find the instructions in this owner’s manual clear and easy to follow. If you take a few

minutes to look through it, you’ll learn how to use all the features of your new Audiovox VME 9309TS Mobile Multimedia Receiver for maximum

enjoyment.

Preparation 3

Optional Equipment 4

Warning 4

Installation 5

Wiring Diagram 7

Controls and Indicators 8

Remote Control 10

Using the TFT Monitor 13

Operating Instructions 15

Setup Menu 16

Tuner Operation 20

DVD/VCD Video Operation 23

DVD/CD Audio Operation 29

MP3/USB/WMA/Operation 31

Troubleshooting 32

Care and Maintenance 34

Specifications 35

Warranty Card

Subject to technical changes

PREPARATION

Congratulations on your purchase of the Audiovox VME 9309TS Mobile Multimedia Receiver.

It’s a good idea to read all of the instructions before beginning the installation. We recommend having your Audiovox VME 9309TS installed by

a reputable installation shop.

Features

DVD

• Aspect Ratio - Cinema, Normal and OFF (Standby)

• Fast Forward, Fast Reverse - 2X, 4X, 8x and 32X

• Slow Forward, Slow Reverse - 2X, 4X, 8x and 32X

• Play, Pause, Stop, Next Chapter and Previous Chapter

CD / MP3 / WMA

• CD-Text Compatible

• ID3 Tag Compatible

• Directory Search (MP3 / WMA Only)

• Direct Track Access via Remote control

• Burn Up To 1500 MP3 and WMA Files onto a DVD+R /RW

• Audible Forward / Reverse Track Search

• Random, Repeat and Intro

• Play, Pause, Stop, Next Track and Previous Track

AM-FM-RDS

• USA/Europe/Latin America/Asia Frequency Spacing

• 30 Station Presets (18 FM, 12 AM)

• Auto Stereo/Mono

• Local/Distance

• Auto Store/Preview Scan

• RDS (Radio Data System)

Chassis

• 1.0 DIN (Import / ISO-DIN Mountable)

• Motorized Flip-Out / Flip-Up LCD Screen

• 8 Character / Segment Type Secondary LCD Display

• 7" TFT Active Matrix LCD w/ Anti-Glare Coating

• 336,960 Sub Pixels (1440W X 234H)

• Pixel Pitch - 0.321W X 0.370H

• Screen Tilt

• Beep Tone Confirmation (On-OFF Option)

• Heat Management System - Forced Air Cooling to keep the chip sets operating at nominal temperatures

• USB 1.0 (500 mA max.)

General

• Navigation Ready (NAV101 or NAV102)

• 44-Key Infrared Remote Control

• One Composite Video Output for Additional Screens

• One Audio / Video Auxiliary Input for Game Console, Camcorder, Navigation, etc.

• Three-Band Tone control (Bass, Mid and Treble) w/ seven Preset EQ Curves

• Front, Rear and Subwoofer Line Output

• Subwoofer Phase Control - 0 ~ 180 degrees

• Programmable Volume Control

• Rear Camera Input (Normal and Mirror Image View)

• Touch Screen Calibration Mode

• 100-Ohm Preamp Line Output - All Audio Channels

• 2VRMS Line Output - All Channels

• Rotary Encoder Audio Control

Subject to technical changes

Optional Equipment

• NAV101/NAV102

The VME 9309TS is "navigation ready." Before accessing any navigation features, you must purchase and install the NAV module. All installation

and operating instructions will be included with the NAV navigation module. Once the NAV is connected and operating properly, the NAV source

mode will become active. While the NAV is not installed, the NAV option appears gray, indicating the function is not available.

• Rear Camera

The VME 9309TS is "camera ready." Before accessing any camera features, you must purchase and install a rear video camera. Once the rear came-

ra is connected and operating properly, the CAMERA source mode will become active. While the camera is not installed, the CAMERA option

appears gray, indicating the function is not available.

Tools and Supplies

You will need these tools and supplies to install your VME 9309TS:

• Torx type, flat-head and Philips screwdrivers

• Wire cutters and strippers

• Tools to remove existing radio (screwdriver, socket wrench set or other tools)

• Electrical tape

• Crimping tool

• Volt meter/test light

• Crimp connections

• 18 gauge wire for power connections

• 16 – 18 gauge speaker wire

Disconnecting the Battery

To prevent a short circuit, be sure to turn off the ignition and remove the negative (-) battery cable prior to installation.

NOTE:

If the VME 9309TS is to be installed in a car equipped with an on-board drive or navigation computer, do not disconnect the battery cable. If the

cable is disconnected, the computer memory may be lost. Under these conditions, use extra caution during installation to avoid causing a short

circuit.

WARNING! Only connect the unit to a12-volt power supply with proper grounding.

WARNING! Never install this unit where operation and viewing could interfere with safe driving conditions.

WARNING! To reduce the risk of a traffic accident (except when using for rear view video camera) never use the video display function while

driving the vehicle. This is a violation of federal law.

WARNING! Never disassemble or adjust the unit.

WARNING! To prevent injury from shock or fire, never expose this unit to moisture or water.

WARNING! Never use irregular discs.

WARNING! To prevent damage to the mechanism inside this unit, avoid impact to the TFT monitor.

WARNING! Using an improper fuse may cause damage to the unit and result in a fire.

WARNING! The monitor employs an automatic motorized mechanism. To prevent damage to the core mechanism, please do not push, pull or

swivel the monitor manually.

Subject to technical changes

INSTALLATION

Pre-installation

1. Press the metal levers on both sides to remove the halfsleeve from the radio.

2. Install the half-sleeve.

a. Install adapter if necessary (optional).

b. Install half-sleeve into adapter or dashboard (use only the supplied screws). Do not force the sleeve into the opening or cause it to bend or bow.

c. Locate the series of bend-tabs along the top, bottom and sides of the mounting sleeve. With the sleeve fully inserted into the dashboard

opening, bend as many of the tabs outward as necessary so that the sleeve is firmly secured to the dashboard.

d. Install support strap to make the unit more stable.

CAUTION! Be careful not to damage the car wiring.

3. Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve.

Wiring

Complete wiring as illustrated in the wiring diagram on page 8. Once the wiring is complete, reconnect the battery negative terminal. If there is no

ACC available, connect the ACC lead to the power supply with a switch.

NOTE:

When replacing a fuse, be sure to use correct type and amperage to avoid damaging the radio. The VME 9309TS uses one 15 amp mini-ATM fuse,

located in the black filter box in-line with the main wire harness.

Final Installation

After completing the wiring connections, turn the unit on to confirm operation (ignition switch must be on). If unit does not operate, recheck all wiring

until problem is corrected. Once proper operation is achieved, turn off the ignition switch and proceed with final mounting of the chassis.

1. Connect wiring adapter to existing wiring harness.

2. Connect antenna lead.

3. Carefully slide the radio into the half-sleeve, making sure it is right-side-up, until it is fully seated and the spring clips lock it into place.

Subject to technical changes

NOTE:

For proper operation of the CD/DVD player, the chassis must be mounted within 20° of horizontal. Make sure the unit is mounted within this limita-

tion.

4. Attach one end of the perforated support strap (supplied) to the screw stud on the rear of the chassis using the hex nut provided. Fasten

the other end of the perforated strap to a secure part of the dashboard either above or below the radio using the screw and hex nut provided.

Bend the strap to position it as necessary.

CAUTION! The rear of the radio must be supported witht he strap to prevent damage to the dashboard from the weight of the radio or improper

operation due to vibration.

5. Replace any items you removed from the dashboard.

Final ISO-DIN Installation

1. Remove trim ring.

2. Mount factory brackets on new radio using existing screws from old radio.

3. Slide radio chassis into dash opening and secure.

4. Reinstall dash panel.

Subject to technical changes

Wiring Diagram

CONTROLS AND INDICATORS

Button Operation

1. OPEN/CLOSE

Press to activate the automatic mechanical system and move the TFT monitor into viewing position. Press again to close the TFT.

2.  WIDE/NAV/DISP

When the monitor is retracted the station search function is started in the direction of lower frequencies by pressing button . If button is pres-

sed briefly when the monitor is extended, the image switches between Full and Standby mode for the monitor. If button is pressed and held, the

optionally available navigation module appears and the audio stream from the previously selected source keeps playing in the background. The

touch screen operation for the navigation interface is inactive in this "MIX" mode. In order to be able to execute TS settings you will need to switch

off the "MIX" mode by pressing and holding button again.

3. / TILT

When the monitor is retracted the station search function is started in the direction of higher frequencies by pressing .

Pressing the TILT button when the monitor is extended activates the angular adjustment function of the monitor, which can be adapted to require-

ments by using the volume controller.

4. BAND/PIC

When the monitor is retracted you can switch between FM 1/2/3 and AM1/2 by pressing the BAND button.

When the monitor is extended the brightness and contrast settings can be adjusted by pressing the PIC button.

5. AUDIO/LO/DX

Rotate to adjust the volume. Press and release to enter and/ or confirm audio settings. Press and hold to activate the Local (LOC) setting.

6. SRC

Briefly pressing the SRC button switches on the device. The device is switched off by pressing and holding the SRC button. Briefly pressing the

SRC button while the device is switched on and the monitor is retracted activates the source selection function, which appears on the small

display. Press this button again repeatedly to alternate between the various sources. The source indicated on the display is selected after 3 seconds.

Pressing the SRC button when the monitor is extended displays the source selection menu on the screen, where you are then able to make your

selection via the touch screen function.

7. LCD Display

8. FRONT AV INPUT

The front audio/video input function can be selected via the source selection menu (AUX1).

You can connect portable media devices to this input. For details of the connector assignment please refer to page 9.

9. IR Remote Control Receiver

10. RESET

Press to reset system settings to factory default (except the password and parental lock setting).

11. ( )

Press once for disc insertion/ejection.Press and hold to reset core mechanism position.

12. TFT Display

13. USB connection

Front USB input including "slidable" cover. The USB input can accommodate standard USB media devices that do not exceed a maximum ampe-

rage of 500 mA. Audio and video formats can be played back via this input.

Connectable media include e.g. MP3 players, USB sticks and cameras (provided that these cameras save images in JPEG format).

14. DISP

In the CD/DVD mode the DISP (Display) button activates the upper status line which includes additional information relating to the disc, such as the

track number and running time.

Subject to technical changes

REMOTE CONTROL

NOTE: Your remote control may differ slightly from the one pictured here. The above diagram is for illustrative purposes only.

Other manuals for VME 9309TS

This manual suits for next models

Table of contents

Audiovox VME 9309TS User manual

Popular Car Video System manuals by other brands