Audix Fisuon Series User manual

F14
OVERVIEW:
The F14 is a dynamic instrument microphone designed for live
sound and studio applications. Characterized with a tailored
frequency response of 30 Hz - 10 kHz, the F14 is ideally suited
for instruments requiring bass reproduction. A cardioid pick-up
pattern helps to minimize feedback and isolate the instrument
from ambient sound coming from the room or from other
instruments on stage.
Compact and roadworthy, the F14 features a durable die cast
zinc alloy body, steel mesh grill, and integrated mic clip.
Low impedance and balanced output allow interference-free
performance even with long cable runs.
SUPPLIED ACCESSORIES:
Carrying pouch (P1)
OPTIONAL ACCESSORIES:
STAND-KD - adjustable kick drum mic stand
TRIPOD - Tripod mic stand
DFLEX - All purpose percussion clamp
DVICE - Spring loaded rim mount clamp
DCLAMP - Tension rod mic clamp
CBL-20 - 20’ XLR-XLR mic cable
CBL-DR25 - 25’ right angle XLR-XLR mic cable
DYNAMIC KICK DRUM MICROPHONE
F14
DFLEX STAND-KD TRIPOD CBL-20
APPLICATIONS:
Kick drum
Bass cabinet
Leslie bottom
FEATURES:
Tailored frequency response
Upper mid-range attack and clarity
Integral mic clip attached
5 year warranty
Dynamic Instrument

SPECIFICATIONS: ARCHITECTS AND ENGINEERS SPECIFICATIONS:
The microphone shall be of the dynamic type available in a cardioid polar pattern. The
nominal output impedance shall be equal to 200 ohms at 1 kHz. The microphone shall have
a sensitivity at of 1.2 mV / Pa at 80 Hz. The microphone shall have a maximum SPL level
of ≥144 dB with THD of 0.5%. The microphone body shall be of die cast zinc alloy. The
dimensions shall be 22 mm in diameter at the base, 58 mm in diameter at the widest point
and 120 mm in length. The microphone shall be the Audix F14.
OPERATION:
The F14 is a low impedance microphone and should be plugged into a “mic level” input
on your console, mixer, or recording device. Please note that the F14 does not require
phantom power and will not be effected in any way by phantom power should it be running
simultaneously while the microphone is in operation. Avoid plugging or unplugging the
microphone from the PA system unless the channel is muted or the volume of the
system turned down. Failure to do so may result in a loud “popping” noise which could
seriously damage the speakers in the PA system.
USER TIPS:
For kick drum, the F14 can be used with the Audix STAND-KD which is designed to place
the F14 in the optimum position for your kick drum. As a general rule, start with the mic
positioned centered inside the middle of the drum pointed towards the beater. For more
attack, and less bass boom, move the mic closer to the beater. For less attack and more
bass, move the mic further away from the beater. For kick drums without hole in front head,
place the F14 a few inches from head for a full and rich sound.
For bass cabinets, position the mic 90 degrees to the grill cloth and 1-2 inches inside the
edge of the speaker.
*Further miking techniques may be found on our website at www.audixusa.com
www.audixusa.com Call: 503-682-6933 Fax: [phone]
Audix Corporation 9400 SW Barber Street, Wilsonville, OR 97070
FREQUENCY / POLARS:
SERVICE AND WARRANTY:
This microphone is under warranty for
a period of 5 years from any and all
manufacturing defects. Should your
microphone fail in any way, please
contact the Audix Service department
at 503-682-6933. A Return Authoriza-
tion number is required before returning
any products.
To register your
microphone, please visit
www.audixusa.com
CARE AND MAINTENANCE:
The F14 is manufactured to exacting specs with
roadworthy construction. However, the capsule
is highly sensitive and should be handled with
care. Avoid extreme temperatures and be sure
to store your microphone in the pouch provided
when not in use. Moisture of any kind can
adversely affect the sound and performance of
your microphone.
***All specications subject to change without notice.
Transducer Type Dynamic
Frequency Response 30 Hz - 10 kHz
Polar Pattern Cardioid
Output Impedance 200 ohms
Sensitivity at 80Hz 1.2 mV / Pa
Capsule Technology Double dome
Off Axis Rejection >20 dB
Maximum SPL ≥ 144 dB
Power Requirements None
Connector 3 pin gold plated
male XLR connector
Polarity Positive pressure on diaphragm
produces positive voltage on pin 2
relative to pin 3 of output
XLR connector
Housing / Finish Die cast zinc /
Black E-Coat
Weight 283.5 g / 10 ounces
Length 120 mm / 4.72 inches
DIMENSIONS (mm):
F14