Autel MaxiSys MS906TS User manual

i
Trademarks
Autel®, MaxiSys®, MaxiDAS®, MaxiScan®, MaxiTPMS®, MaxiRecorder®, and
MaxiCheck®are trademarks of Autel Intelligent Technology Corp., Ltd., registered in
China, the United States and other countries. All other marks are trademarks or
registered trademarks of their respective holders.
Copyright Information
No part of this manual may be reproduced, stored in a retrieval system or transmitted,
in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise without the prior written permission of Autel.
Disclaimer of Warranties and Limitation of Liabilities
All information, specifications and illustrations in this manual are based on the latest
information available at the time of printing. Autel reserves the right to make changes at
any time without notice. While information of this manual has been carefully checked
for accuracy, no guarantee is given for the completeness and correctness of the
contents, including but not limited to the product specifications, functions, and
illustrations.
Autel will not be liable for any direct damages or for any special, incidental, or indirect
damages or for any economic consequential damages (including the loss of profits).
IMPORTANT: Before operating or maintaining this unit, please read this manual
carefully, paying extra attention to the safety warnings and precautions.
For Services and Support:
pro.autel.com
www.autel.com
1-855-288-3587/1-855-AUTELUS (North America)
0086-755-86147779 (China)
[email protected]
For technical assistance in all other markets, please contact your local distributor.

ii
Safety Information
For your own safety and the safety of others, and to prevent damage to the device and
vehicles upon which it is used, it is important that the safety instructions presented
throughout this manual be read and understood by all persons operating or coming into
contact with the device.
There are various procedures, techniques, tools, and parts for servicing vehicles, as
well as in the skill of the person doing the work. Because of the vast number of test
applications and variations in the products that can be tested with this equipment, we
cannot possibly anticipate or provide advice or safety messages to cover every
circumstance. It is the automotive technician’s responsibility to be knowledgeable of the
system being tested. It is crucial to use proper service methods and test procedures. It
is essential to perform tests in an appropriate and acceptable manner that does not
endanger your safety, the safety of others in the work area, the device being used, or
the vehicle being tested.
Before using the device, always refer to and follow the safety messages and applicable
test procedures provided by the manufacturer of the vehicle or equipment being tested.
Use the device only as described in this manual. Read, understand, and follow all
safety messages and instructions in this manual.
Safety Messages
Safety messages are provided to help prevent personal injury and equipment damage.
All safety messages are introduced by a signal word indicating the hazard level.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury to the operator or to bystanders.
WARNING: Indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury to the operator or to bystanders.
Safety Instructions
The safety messages herein cover situations Autel is aware of. Autel cannot know,
evaluate or advise you as to all of the possible hazards. You must be certain that any
condition or service procedure encountered does not jeopardize your personal safety.
DANGER: When an engine is operating, keep the service area WELL
VENTILATED or attach a building exhaust removal system to the engine exhaust
system. Engines produce carbon monoxide, an odorless, poisonous gas that
causes slower reaction time and can lead to serious personal injury or loss of
life.

Safety Information Important Safety Instructions
iii
Do Not Turn the Volume Up Too Loud When Using Headphones
Listening at high volumes that over-stimulate the ear for long periods of time
may result in loss of hearing.
SAFETY WARNINGS:
Always perform automotive testing in a safe environment.
Wear safety eye protection that meets ANSI standards.
Keep clothing, hair, hands, tools, test equipment, etc. away from all
moving or hot engine parts.
Operate the vehicle in a well-ventilated work area, for exhaust gases are
poisonous.
Put the transmission in PARK (for automatic transmission) or NEUTRAL
(for manual transmission) and make sure the parking brake is engaged.
Put blocks in front of the drive wheels and never leave the vehicle
unattended while testing.
Be extra cautious when working around the ignition coil, distributor cap,
ignition wires and spark plugs. These components create hazardous
voltages when the engine is running.
Keep a fire extinguisher suitable for gasoline, chemical, and electrical fires
nearby.
Do not connect or disconnect any test equipment while the ignition is on or
the engine is running.
Keep the test equipment dry, clean, free from oil, water or grease. Use a
mild detergent on a clean cloth to clean the outside of the equipment as
necessary.
Do not drive the vehicle and operate the test equipment at the same time.
Any distraction may cause an accident.
Refer to the service manual for the vehicle being serviced and adhere to
all diagnostic procedures and precautions. Failure to do so may result in
personal injury or damage to the test equipment.
To avoid damaging the test equipment or generating false data, make
sure the vehicle battery is fully charged and the connection to the vehicle
DLC is clean and secure.
Do not place the test equipment on the distributor of the vehicle. Strong
electro-magnetic interference can damage the equipment.

iv
Contents
CHAPTER 1 USING THIS MANUAL........................................................................... 1
1.1 CONVENTIONS..................................................................................................... 1
1.1.1 Bold Text................................................................................................... 1
1.1.2 Notes.........................................................................................................1
1.1.3 Important..................................................................................................1
1.1.4 Hyperlink...................................................................................................1
1.1.5 Procedure..................................................................................................1
CHAPTER 2 GENERAL INTRODUCTION....................................................................3
2.1 MAXISYS SYSTEM DISPLAY TABLET...........................................................................3
2.1.1 Functional Description..............................................................................3
2.1.2 Power Sources...........................................................................................5
2.1.3 Technical Specifications............................................................................ 6
2.2 VCI – WIRELESS DIAGNOSTIC INTERFACE..................................................................7
2.2.1 Functional Description..............................................................................7
2.2.2 Technical Specifications............................................................................ 8
2.2.3 Power Sources...........................................................................................9
2.3 ACCESSORY KIT.................................................................................................... 9
2.3.1 OBD I Adapters......................................................................................... 9
2.3.2 Other Accessories................................................................................... 10
CHAPTER 3 GETTING STARTED.............................................................................. 11
3.1 POWERING UP...................................................................................................11
3.1.1 Application Buttons................................................................................ 12
3.1.2 Locator and Navigation Buttons.............................................................14
3.1.3 System Status Icons................................................................................ 15
3.2 POWERING DOWN..............................................................................................16
3.2.1 Reboot System........................................................................................ 17
3.3 INSTALLING COMPUTER SOFTWARE........................................................................17
3.3.1 Printing Operation.................................................................................. 17
CHAPTER 4 DIAGNOSTICS OPERATIONS............................................................... 19
4.1 ESTABLISHING VEHICLE COMMUNICATION............................................................... 19
4.1.1 Vehicle Connection................................................................................. 19
4.1.2 VCI Connection........................................................................................20
4.1.3 No Communication Message..................................................................22
4.2 GETTING STARTED.............................................................................................. 23
4.2.1 Vehicle Menu Layout.............................................................................. 23

v
4.3 VEHICLE IDENTIFICATION...................................................................................... 25
4.3.1 Auto VIN Scan......................................................................................... 25
4.3.2 Manual VIN Input................................................................................... 26
4.3.3 Manual Vehicle Selection........................................................................27
4.3.4 Alternative Vehicle Identification........................................................... 28
4.4 NAVIGATION...................................................................................................... 28
4.4.1 Diagnostics Screen Layout......................................................................28
4.4.2 Screen Messages.................................................................................... 31
4.4.3 Making Selections...................................................................................32
4.5 MAIN MENU..................................................................................................... 32
4.6 DIAGNOSIS........................................................................................................ 32
4.6.1 ECU Information..................................................................................... 36
4.6.2 Read Codes............................................................................................. 37
4.6.3 Erase Codes.............................................................................................38
4.6.4 Live Data.................................................................................................39
4.6.5 Active Test...............................................................................................45
4.6.6 Special Functions.................................................................................... 46
4.7 SERVICE............................................................................................................ 47
4.7.1 Function Descriptions............................................................................. 48
4.8 GENERIC OBD II OPERATIONS.............................................................................. 49
4.8.1 General Procedure.................................................................................. 49
4.8.2 Function Descriptions............................................................................. 51
4.9 EXITING DIAGNOSTICS......................................................................................... 53
CHAPTER 5 TPMS SERVICE OPERATIONS.............................................................. 55
5.1 NAVIGATION...................................................................................................... 55
5.1.1 TPMS Service Screen Layout................................................................... 55
5.2 CHECK OPERATIONS............................................................................................ 57
5.3 PROGRAMMING OPERATIONS............................................................................... 59
5.3.1 Copy by Activation..................................................................................60
5.3.2 Copy by OBD........................................................................................... 61
5.3.3 Auto Create.............................................................................................62
5.3.4 Manual Create........................................................................................62
5.4 RELEARN OPERATIONS.........................................................................................63
5.4.1 OBD II Relearn.........................................................................................64
5.4.2 Read IDs from vehicle............................................................................. 65
5.4.3 Read DTC.................................................................................................65
5.4.4 Clear DTC................................................................................................ 65
CHAPTER 6 MAXIFIX OPERATIONS........................................................................66
6.1 NAVIGATION...................................................................................................... 66

vi
6.1.1 Terminology............................................................................................ 68
6.2 OPERATIONS...................................................................................................... 69
6.2.1 Home...................................................................................................... 70
6.2.2 Search Fix Features.................................................................................70
6.2.3 Ask.......................................................................................................... 70
6.2.4 My MaxiFix............................................................................................. 71
6.2.5 My Messages..........................................................................................73
6.2.6 Support................................................................................................... 74
CHAPTER 7 SHOP MANAGER OPERATIONS.......................................................... 75
7.1 VEHICLE HISTORY................................................................................................76
7.1.1 Historical Test Record..............................................................................77
7.2 WORKSHOP INFORMATION...................................................................................78
7.3 CUSTOMER MANAGER.........................................................................................79
7.3.1 History Notes.......................................................................................... 80
CHAPTER 8 DATA MANAGER OPERATIONS...........................................................83
8.1 OPERATIONS...................................................................................................... 83
8.1.1 Image Files..............................................................................................83
8.1.2 PDF Files..................................................................................................85
8.1.3 Review Data............................................................................................85
8.1.4 Apps Manager........................................................................................ 86
8.1.5 Data Logging.......................................................................................... 86
CHAPTER 9 SETTINGS OPERATIONS...................................................................... 87
9.1 OPERATIONS...................................................................................................... 87
9.1.1 Unit......................................................................................................... 87
9.1.2 Language................................................................................................ 87
9.1.3 Printing Setting....................................................................................... 88
9.1.4 Notification Center................................................................................. 88
9.1.5 About...................................................................................................... 89
9.1.6 System Settings.......................................................................................89
CHAPTER 10 UPDATE OPERATIONS.........................................................................91
CHAPTER 11 VCI MANAGER OPERATIONS.............................................................. 94
11.1 BT PAIRING....................................................................................................94
11.2 UPDATE.........................................................................................................95
11.3 TPMS MODULE UPDATE................................................................................. 96
CHAPTER 12 SUPPORT OPERATIONS...................................................................... 97
12.1 PRODUCT REGISTRATION.................................................................................. 97
12.2 SUPPORT SCREEN LAYOUT................................................................................ 98

vii
12.3 MYACCOUNT................................................................................................ 98
12.4 USER COMPLAINT........................................................................................... 99
12.5 DATA LOGGING............................................................................................. 101
12.6 COMMUNITIES..............................................................................................102
12.7 TRAINING CHANNELS.....................................................................................105
12.8 FAQ DATABASE............................................................................................ 105
CHAPTER 13 TRAINING OPERATIONS................................................................... 106
CHAPTER 14 REMOTE DESK OPERATIONS............................................................ 107
14.1 OPERATIONS................................................................................................ 107
CHAPTER 15 QUICK LINK OPERATIONS.................................................................109
CHAPTER 16 OSCILLOSCOPE OPERATIONS........................................................... 110
16.1 SAFETY INFORMATION....................................................................................110
16.2 GLOSSARY....................................................................................................112
16.3 MAXISCOPE MODULE....................................................................................114
16.4 SCREEN LAYOUT AND OPERATIONS...................................................................117
16.4.1 Top Toolbar........................................................................................118
16.4.2 Functional Buttons............................................................................ 121
16.4.3 Measurement Grid............................................................................122
16.4.4 Measurement Rulers.........................................................................123
16.4.5 Functional Buttons............................................................................ 124
16.5 TROUBLESHOOTING....................................................................................... 125
16.6 MAXISCOPE FIRMWARE UPDATE..................................................................... 126
CHAPTER 17 DIGITAL INSPECTION OPERATIONS.................................................. 127
17.1 ADDITIONAL ACCESSORIES.............................................................................. 128
17.1.1 Technical Specifications.....................................................................131
17.2 OPERATIONS................................................................................................ 131
CHAPTER 18 MAINTENANCE AND SERVICE.......................................................... 134
18.1 MAINTENANCE INSTRUCTIONS.........................................................................134
18.2 TROUBLESHOOTING CHECKLIST........................................................................ 135
18.3 ABOUT BATTERY USAGE.................................................................................135
18.4 SERVICE PROCEDURES....................................................................................136
CHAPTER 19 COMPLIANCE INFORMATION...........................................................138
CHAPTER 20 WARRANTY.......................................................................................140

1
Chapter 1 Using This Manual
This manual contains device usage instructions.
Some illustrations shown in this manual may contain modules and optional equipment
that are not included in your system. Contact your sales representative for availability of
other modules and optional tools or accessories.
1.1 Conventions
The following conventions are used.
1.1.1 Bold Text
Bold text is used to highlight selectable items such as buttons and menu
options.
Example:
Tap OK.
1.1.2 Notes
ANOTE provides helpful information such as additional explanations, tips,
and comments.
1.1.3 Important
IMPORTANT indicates a situation which, if not avoided, may result in damage
to the test equipment or vehicle.
1.1.4 Hyperlink
Hyperlinks, or links, that take you to other related articles, procedures, and
illustrations are available in electronic documents. Blue colored text indicates
a selectable hyperlink.
1.1.5 Procedure
An arrow icon indicates a procedure.
Example:

Using This Manual Conventions
2
To use the camera:
1 Tap the Camera button. The camera screen opens.
2 Focus the image to be captured in the view finder.
3 Tap the blue circle. The view finder now shows the captured picture
and auto-saves the taken photo.

3
Chapter 2 General Introduction
The MaxiSys MS906BT/MaxiSys MS906TS is an advanced smart wireless diagnostic
device providing specialized automotive diagnostic service for customers. Featuring the
powerful Samsung Exynos 5260 6-core processor (1.3 GHz quad-core ARM Cortex-A7
+ 1.7 GHz dual-core ARM Cortex-A15), an 8.0 inch LED capacitive touch screen, and
long-distance wireless communication, based on the multitasking mobile operating
system, and combined with the best possible coverage of OE-level diagnostics, the
MaxiSys MS906TS/MS906BT performs comprehensive vehicle diagnostics and
analysis efficiently. With the integrated TPMS module, the MaxiSys MS906TS also
provides comprehensive TPMS solutions.
There are two main components to the MaxiSys system:
MaxiSys System Display Tablet – the central processor and monitor for the
system
Vehicle Communication Interface (VCI) – the device for accessing vehicle data
This manual describes the construction and operation of both the devices and how they
work together to deliver diagnostic solutions.
2.1 MaxiSys System Display Tablet
2.1.1 Functional Description
Figure 2- 1 Display Tablet Front View
1. 8.0” LED Capacitive Touch Screen
2. Power LED – indicates battery level & charging or system status

General Introduction MaxiSys System Display Tablet
4
3. Ambient Light Sensor – detects ambient brightness
4. Microphone
5. TPMS Service Symbol – indicates the position of the embedded TPMS
antenna (for MaxiSys MS906TS only)
The power LED displays different colors in response to the following
scenarios:
A. Green
Illuminates green when the Display Tablet is charging and the
battery level is above 90%.
B. Yellow
Illuminates yellow when the Display Tablet is charging and the
battery level is below 90%.
C. Red
Illuminates red when the Display Tablet is powered on and the
battery level is below 15%.
D. Blue
Illuminates blue when the MaxiSys system is fault.
Figure 2- 2 Display Tablet Back View
1. Camera Lens
2. Camera Flash
3. Collapsible Stand – extends from the back to allow hands-free viewing of
the Display Tablet at a 30-degree angle

General Introduction MaxiSys System Display Tablet
5
Figure 2- 3 Display Tablet Top View
1. Mini SD Card Slot – holds the mini SD Card
2. Mini USB OTG Port
3. DC Power Supply Input Port – connects the 12 volt power adapter to
charge.
4. HDMI (high-definition multimedia interface) Port
5. USB Port
6. Headset Jack (3-Band 3.5mm )
7. Lock/Power Button – turns the device on & off with long press, or locks
the screen with short press
2.1.2 Power Sources
The Display Tablet can receive power from any of the following sources:
Internal Battery Pack
AC/DC Power Supply
Vehicle Power Supply
Internal Battery Pack
The Display Tablet can be powered with the internal rechargeable battery,
which if fully charged can provide sufficient power for about 14 hours of
continuous operation.
AC/DC Power Supply
The Display Tablet can be powered from a wall socket using the AC/DC power
adapter. The AC/DC power supply also charges the internal battery pack.

General Introduction MaxiSys System Display Tablet
6
Vehicle Power
The Display Tablet can be powered from the cigarette lighter or other suitable
power port on the test vehicle through a direct cable connection. The vehicle
power cable connects to the DC power supply port on the top side of the
display unit.
2.1.3 Technical Specifications
Table 2- 1 Technicial Specifications
Item
Description
Operating System
AndroidTM 4.4.2, KitKat
Processor
Samsung Exynos T5260 6-Core Processor (1.3
GHz quad-core ARM Cortex-A7 + 1.7 GHz
dual-core ARM Cortex-A15)
Memory
2 GB RAM & 32 GB ROM
Display
8.0 inch LED capacitive touch screen with
1024x768P resolution
Connectivity
Wi-Fi (802.11 b/g/n)
USB: 2.0
Mini USB 2.0
Wireless BT V2.1+EDR, Class1
HDMI 1.4a
SD Card (support up to 32GB)
Camera (rear)
Rear-facing, 8.0 Megapixel, AF with Flashlight
Sensors
Gravity Accelerometer, Ambient Light Sensor
(ALS)
Audio Input/Output
Microphone
Single Speakers
3-Band 3.5 mm stereo/standard headset jack
Power and Battery
10,000 mAh 3.7 V lithium-polymer battery
Charging via 12 V AC/DC power supply
Input Voltage
12 V (9-35 V)
Power Consumption
5 W

General Introduction MaxiSys System Display Tablet
7
Item
Description
Operating Temp.
0 to 55°C (32 to 131°F)
Storage Temp.
-20 to 60°C (-4 to 140°F)
Housing
Strong plastic housing with protective rubber boot
Dimensions (W x H x D)
270.8 mm (10.0”) x 176.0 mm (6.9”) x 36.0 mm
(1.4”)
Weight
NW: 1.10 kg (2.42 lb.) (for 906TS)
NW: 1.05 kg (2.31 lb.) (for 906BT)
Supported
Automotive
Protocols
ISO 9142-2, ISO 14230-2, ISO 15765-4, K-Line,
L-Line, Flashing Code, SAE-J1850 VPW,
SAE-J1850 PWM, CAN ISO 11898, Highspeed,
Middlespeed, Lowspeed and Singlewire CAN, GM
UART, UART Echo Byte Protocol, Honda Diag-H
Protocol, TP 2.0, TP 1.6, SAE J1939, SAE J1708,
Fault-Tolerant CAN
2.2 VCI – Wireless Diagnostic Interface
The wireless diagnostic interface MaxiVCI V100 is a small vehicle
communication interface (VCI) used to connect to a vehicle’s diagnostic
connector (DLC) and connect with the Display Tablet, as well as standalone
PC, as a vehicle communication interface (VCI) for vehicle data transmission.
2.2.1 Functional Description
Figure 2- 4 MaxiVCI V100 Wireless Diagnostic Interface

General Introduction VCI – Wireless Diagnostic Interface
8
1. Lighting Push Button – presses to turn on the white LED in the vehicle
data connector socket
2. Power LED – indicates power and system status
Green: illuminates solid green when powered on.
Amber: flashes green and amber automatically when performing
firmware update.
Red: illuminates red automatically when powered up, and flashes red
when system failure occurs.
3. Vehicle LED – flashes green when communicating with the vehicle’s
system
4. Connection Mode LED – illuminates solid green when the device is
properly connected with the Display Tablet or PC via the USB cable, or
illuminates solid blue via wireless BT connection
5. Vehicle Data Connector (16-pin)
6. USB Port
Communication
The Wireless Diagnostic Interface supports both the wireless BT and the USB
communication. It can transmit vehicle data to the Display Tablet with or
without a physical connection. The working range of the transmitter through
BT communication is about 164 feet (about 50 m). A signal lost due to moving
out of range automatically restores itself when the Display Tablet is brought
closer to the VCI unit.
2.2.2 Technical Specifications
Table 2- 2 Technical Specifications
Item
Description
Communications
BT V.2.1 + EDR
USB 2.0
Wireless Frequency
2.4 GHz
Input Voltage Range
12 VDC
Supply Current
150 mA @ 12 VDC

General Introduction VCI – Wireless Diagnostic Interface
9
Operating Temperature
0°C to 50°C (ambient)
Storage Temperature
-20°C to 70°C (ambient)
Dimensions (L x W x H)
87.0 mm (3.43”) x 52.0 mm (2.05”) x24.5 mm
(0.96”)
Weight
0.076 kg (0.168 lb.)
Built-in Battery
3.7V Lithium Battery
Light
White LED
2.2.3 Power Sources
The Wireless Diagnostic Interface operates on 12-volt vehicle power, which it
receives through the vehicle data connection port. The unit powers on
whenever it is connected to an OBD II/EOBD compliant data link connector
(DLC).
2.3 Accessory Kit
2.3.1 OBD I Adapters
The OBD I adapters are for Non-OBD II vehicles. The adapter used depends
on the type of vehicle being tested. The most common adapters are shown
below. (Benz-14, Chrysler-16, Fiat-3 and PSA-2 are optional, please contact
your local distributors for details.)
Benz-14
Chrysler-16
BMW-20
Kia-20
Nissan-14
GM/Daewoo-12
Honda-3
VW/Audi-2+2

General Introduction Accessory Kit
10
Mitsubishi/
Hyundai -12+16
Benz-38
Fiat-3
PSA-2
2.3.2 Other Accessories
Mini USB Cable
Connects the Display Tablet to the PC or the VCI unit.
AC/DC External Power Adapter
Connects the Display Tablet to the external DC power
port for power supply.
Cigarette Lighter
Provides power to the Display Tablet through
connection to the vehicle’s cigarette lighter receptacle.
Lighter Fuse
A safety device for the cigarette lighter.

11
Chapter 3 Getting Started
Make sure the Display Tablet has sufficient battery level or is connected to the DC
power supply (see 2.1.2 Power Sources on page 5).
NOTE: The images and illustrations depicted in this manual may differ from the actual
ones.
3.1 Powering Up
Press the Lock/Power button on the top right side of the Display Tablet to
switch the unit on. The system boots up, and shows the lock screen. Pressing
the inner ring with a Lock icon at the center displays 3 entry options:
1. Unlock – drags the inner ring to the right edge of the circle to enter the
Android System’s Home Screen.
2. MaxiSys – drags the inner ring to the top edge of the circle to enter the
MaxiSys Job Menu.
3. Camera – drags the inner ring to the left edge of the circle to launch the
camera
Figure 3- 1 Sample MaxiSys MS906TS Job Menu

Getting Started Powering Up
12
Figure 3- 2 Sample MaxiSys MS906BT Job Menu
1. Application Buttons
2. Locator and Navigation Buttons
3. Status Icons
NOTE: The screen is locked by default when you first turn on the Display
Tablet. It is recommended to lock the screen to protect the information in the
system and reduce the power consumption.
Almost all operations on the Display Tablet are controlled through the touch
screen. The touch screen navigation is menu driven, which allows you to
quickly locate the test procedure, or data that you need, through a series of
choices and questions. Detailed descriptions of the menu structures are found
in the chapters for the various applications.
3.1.1 Application Buttons
The Application buttons configure the MaxiSys for the type of operation or
activity to be performed. The table below gives brief descriptions of the
available applications.
Tap on the screen to select an application from the Job Menu.

Getting Started Powering Up
13
Table 3- 1 Applications
Button
Name
Description
Diagnostics
Configures the unit to operate as a diagnostic
tool. See Diagnostics Operations on page 19.
Data
Manager
Opens the organization system for saved data
files. See Data Manager Operations on page 83.
TMPS
Launches the TPMS service program directly.
See TPMS Service Operations on page 55. (For
MaxiSys MS906TS)
MaxiFix
Launches the MaxiFix platform which provides
the most compatible and abundant repair
techniques and diagnostics database. See
MaxiFix Operations on page 66.
Settings
Allows you to set the MaxiSys system settings,
and to view the general information about the
Display Tablet. See Settings Operations on page
87.
Shop
Manager
Allows you to edit and save workshop
information and customer data, as well as
reviewing test vehicle history records. See Shop
Manager Operations on page 75.
Update
Checks for the latest update available for the
MaxiSys system, and performs updating
procedures. See Update Operations on page 91.
VCI
Manager
Establishes and manages BT connection to the
VCI device. See VCI Manager Operations on
page 94.
Remote
Desk
Configures your unit to receive remote support
using the TeamViewer application program. See
Remote Desk Operations on page 107.
Support
Launches the Support platform which
synchronizes Autel’s on-line service base station
with the MaxiSys tablet. See Support Operations
on page 97.