Auto Page C3-RS-625 User manual

1
C3-RS-625
PROFESSIONAL 2-WAY AM/AM REMOTE CAR STARTER
&
KEYLESSENTRYSYSTEM
WithTwo-waySerialPortDataLink
Compatible
Pleaseseepage15ofthismanualformoredetails
OPERATION MANUAL
Please register your product at:
www.autopageusa.com
THIS PRODUCT IS DESIGNED FOR PROFESSIONAL IN
STALLATION ONLY
MSVMASTER -       - http://www.msvmaster.lv
MSVMASTER -       - http://www.msvmaster.lv

2
SYSTEM OPERATIONS:
WARNINGS:
As with any product that performs automatic functions, there are certain safety
precautionsthatyoumustpracticeandbeawareof.
1.Keepthetransmitteroutofchildren’sreach.
2.Donotleaveanyoneinthevehiclewhilethevehicleisrunningonremote
control.
3. Alert servicing personnel that the vehicle can be started automatically.
4.Donotstartthevehiclebyremotewhileit’sinanenclosedareaorgarage.
5.Alwaysapplytheparkingbrakeandlockthevehicleasyouexitthevehicle.
6.Thevehiclewindowsmustberolledup.
7.Should the unit malfunction, disconnect the fuse until the problem is
corrected.
8.Theuseandoperationsofthissystemisthesoleresponsibilityofthe
operator.
9.Some areas may havelocalordinancesthat prohibit leaving a vehicle
runningonpublicstreets.
10.Itisnotsafetoremotestartthevehicleifthevehicleisparkedonasteep
incline.
Transmitter
Button System Function Remark
Lock Doors All doors lock
Panic function Press and Hold for 3 seconds.
Press to stop panic.
+ Silent Lock / Unlock Ignition in "off" position.
Unlock Doors
-
Two Step Door Unlock (Driver’s
door on the first push; Passenger’s
door on the second push
( optional )
Presstwicewithin3seconds.
-
Car Locator Push while the system is armed
Trunk Release Press and Hold for 2 seconds
Activate or Turn Off The Remote
Start Push once or twice depending on system settings (Program)
II Switching CodeFor2ndCar
Operation. Standard Remote only Push Before Command
MSVMASTER -       - http://www.msvmaster.lv
MSVMASTER -       - http://www.msvmaster.lv

3
CHANGING THE BATTERY IN YOUR TRANSMITTERS
XT-33: This transmitter uses two (2) 3-volt lithium ion batteries (#CR2016)
that are sandwiched together with the (+) side facing upward. To replace
the battery, you will need to use a small flat blade screwdriver. Locate the
small notch on the lower right side of the transmitter case next to the key
ring. Using the flat blade screwdriver, carefully pry the top case from the
bottom case. It should snap apart after breaking the seal. Before
removing the batteries note the direction of the positive (+) terminal.
Place the new batteries in exactly the same manner, being careful not to
bend or damage the contact terminal. Snap the cases back together and
then test the transmitter to insure it arms and disarms the alarm.
XT-43LCD2-Way XT-33
Transceiver Sta ndard Remo te
(1) AAA Battery
ACTIVE LOCK:
1 . P r e s s button on the transmitter.
2 . T h e S i r e n w i l l c h i r p o n c e a n d p a r k i n g l i g h t s w i l l f l a s h o n c e i n d i c a t i n g t h a t
the system is now active. The vehicle doors will lock upon activating
only when interfaced with the keyless entry system.
(2) CR2016
3-VoltBatteries
MSVMASTER -       - http://www.msvmaster.lv
MSVMASTER -       - http://www.msvmaster.lv

4
SILENT LOCKING / UNLOCKING: Pressing the + buttons
together on the transmitter will lock or unlock your system, No chirp sound
will be heard. Lock / unlock confirmation will be seen through the
vehicle’s parking lights only.
ACTIVE UNLOCK:
1 . P r e s s button on the transmitter.
2 . T h e h o r n w i l l c h i r p t w i c e a n d p a r k i n g l i g h t w i l l f l a s h t w i c e t o i n d i c a t i n g
that the keyless system is now unlocked. The vehicle doors will
unlock and dome lights will turn on for 30 seconds.
PATHWAY ILLUMINATION
This feature turns the parking light “ON” for 30 seconds upon a unlock
signal and for 10 seconds upon the lock signal. (Programmable)
TWO STEPS DOOR UNLOCK: This feature will independently unlock the
driver door only when deactivating the system. Pushing the
button a second time within 3 seconds will unlock the entire vehicle.
(Optional)
LED DISPLAY:
L E D F u n c t i o n
Off Unlock
Slow
Flash Locked
On (Solid) Valet Mode
CHIRP INDICATOR:
Chirp Function
1 Chirp Lock
2 Chirps Unl ock
6 Chirps Ca r Locat or
PARKING LIGHTS:
Parking light Fu nct io n
1 Flash Lock
2 Flashes Unloc k
12 Flashes Car Locator
Constant On Under Remote Start
DEACTIVATING WITHOUT A TRANSMITTER
The Override function may be used if the remote transmitter is lost or
inoperative.
1 . E n t e r t h e v e h i c l e a n d t u r n t h e i g n i t i o n s w i t c h t o ‘ O N ’ p o s i t i o n .
2 . W i t h i n 1 0 s e c o n d s p u s h a n d r e l e a s e t h e v a l e t s w i t c h .
MSVMASTER -       - http://www.msvmaster.lv
MSVMASTER -       - http://www.msvmaster.lv

5
You can now start and operate the vehicle normally.
VALET MODE:
The valet switch allows you to temporarily bypass all system function,
eliminating the need to hand your transmitter to parking attendants or
garage mechanics. When the system is in valet mode, and remote start
functions are bypassed, however, the remote panic feature and remote
door locks will remain operational. To use the valet mode, the system
must first be deactivated either by using you remote transmitter, or by
operating the Manual override sequence.
EnterValetMode:
1 . F r o m t h e U n l o c k c o n d i t i o n , t u r n t h e i g n i t i o n t o “ O N ” p o s i t i o n .
2 . P u s h a n d h o l d v a l e t s w i t c h f o r 2 s e c o n d s u n t i l t h e L E D t u r n s o n . T h e
LED will remain on as long as the system is in ‘valet mode’.
Exit Valet Mode:
1 . R e t u r n t o n o r m a l o p e r a t i o n , t u r n i g n i t i o n ‘ o n ’ .
2. Push and hold valet switch for 2 seconds, The LED will turn off
indicating the system has exited the valet mode.
PANIC FUNCTION: (IF SIREN or HORN IS INSTALLED)
The transmitter can be used as a remote panic switch to manually
trigger the vehicle’s horn in case of emergency.
1 . P r e s s a n d h o l d t h e button for 3 second. The siren will immediately
sound.
2 . D u r i n g p a n i c m o d e , t h e n o r m a l f u n c t i o n o f t h i s tr a n s m i t t e r b u t t o n w i l l
be suspended. The and buttons can be used to lock and
unlock the doors (if the option is installed),
3 . T o s t o p t h e p a n i c , p r e s s t h e button on the transmitter again.
4. If no buttons are pressed, the panic function will stop automatically in
30 seconds.
DOME LIGHT CONVENIENCE DELAY & SUPERVISION
This system has a unique feature, which will turn on your vehicle dome
light as follows: (optional) Additional installation required.
Upon unlocking, the interior lights will remain on for 30 seconds.
Note: Turning on the ignition switch or activating the system will turn off
the dome light.
IGNITION CONTROL DOOR LOCKS
If the vehicle’s door locks have been interfaced to the security system,
the system will automatically lock the vehicle’s doors when the ignition
is turned “ON” and /or unlock the vehicle’s doors when the ignition is
MSVMASTER -       - http://www.msvmaster.lv
MSVMASTER -       - http://www.msvmaster.lv

6
turned “OFF”.
TRUNK RELEASE (Additional Installation Required)
Press and hold the button on transmitter for two seconds to remote
control the trunk release or other electric devices.
CAR LOCATOR (ONLY IF SIREN or HORN IS INSTALLED)
Press the button twice when the system is armed to active car
locator function. The horn will chirp 6 times. The parking light will flash 12
times, for you to easily locate your car.
REMOTE START OPERATION:
WARNINGS:
As with any product that performs automatic functions, there are certain
safety precautions that you must practice and be aware of.
1 . K e e p t h e t r a n s m i t t e r o u t o f c h i l d r e n ’ s r e a c h .
2 . D o n o t l e a v e a n y o n e i n t h e v e h i c l e w h i l e r u n n i n g o n r e m o t e c o n t r o l .
3 . A l e r t s e r v i c i n g p e r s o n n e l t h a t t h e v e h i c l e c a n b e s t a r t e d a u t o m a t i c a l l y .
4 . D o n o t s t a r t t h e v e h i c l e b y r e m o t e w h i l e i t ’ s i n a n e n c l o s e d a r e a o r
garage.
5 . A l w a y s a p p l y t h e p a r k i n g b r a k e a n d l o c k t h e v e h i c l e a s y o u e x i t t h e
vehicle.
6 . S h o u l d t h e u n i t m a l f u n c t i o n , d i s c o n n e c t t h e f u s e u n t i l t h e p r o b l e m i s
corrected.
7 . T h e u s e a n d o p e r a t i o n s o f t h i s s y s t e m i s t h e s o l e r e s p o n s i b i l i t y o f t h e
operator.
8. Some areas may have local ordinances that prohibit leaving a vehicle
running on public streets.
A. TO REMOTE START THE VEHICLE:
When you want to start your vehicle,
1 . P r e s s button once on the transmitter.
2 . T h e p a r k i n g l i g h t s w i l l f l a s h t o i n d i c a t e t h e r e m o t e s t a r t r e c e i v e d t h e
signal.
3 . T h e e n g i n e w i l l s t a r t i n a p p r o x i m a t e l y 5 s e c o n d s .
4 . A f e w s e c o n d s a f t e r t h e e n g i n e i s r u n n i n g , t h e p a r k i n g l i g h t s w i l l t u r n
on again and climate controls will activate and adjust the vehicles
interior temperature to your preset setting.
5 . T h e v e h i c l e w i l l r u n f o r a 5 t o 3 0 m i n u t e c y c l e a n d a u t o m a t i c a l l y s h u t
d o w n .
(SAFETY START OPERATION :)
The safety start feature allows you to press the button twice before the
MSVMASTER -       - http://www.msvmaster.lv
MSVMASTER -       - http://www.msvmaster.lv

7
vehicle will remote start or remote shut down. (Programming Required)
NO T E: The Remote Start Unit will not start the vehicle if any one of the
following conditions exists:
1 . T h e h o o d i s o p e n e d .
2 . T h e b r a k e p e d a l i s p r e s s e d .
3 . T h e o p t i o n a l r e m o t e s t a r t e n a b l e t o g g l e s w i t c h i s i n t h e O F F p o s i t i o n .
4 . T h e g e a r s e l e c t o r i s i n a n y g e a r o t h e r t h e n “ P A R K ” o r “ N E U T R A L ”
TO TURN OFF THE REMOTE START:
When the engine is running (by remote start), if you want to stop it,
1 . P r e s s button once on the transmitter.
2 . Move the optional remote start enable toggle switch to OFF position.
(If installed)
3 . P r e s s t h e b r a k e p e d a l , t h e v e h i c l e w i l l s h u t d o w n a n d t u r n o f f t h e p a r k i n g
light to indicate engine stopped.
TO OVERRIDE VEHICLE FROM REMOTE START CONTROL:
To operate the vehicle while it is running from the remote start:
1 . I n s e r t t h e i g n i t i o n k e y a n d t u r n i t t o “ O N ” ( n o t t h e s t a r t ) p o s i t i o n .
2 . P r e s s t h e b r a k e p e d a l .
Note: If the brake pedal is pressed before the key is in the ON
position, the engine will shut down.
TEMPORARY STOP FEATURE:
This feature allows the vehicle to remain running after the key has been
removed from the ignition. This feature is useful for occasions when you
wish to exit and lock the vehicle for short periods of time, but would like to
leave the engine running and the climate control on.
1 . B e f o r e t u r n i n g o f f t h e e n g i n e , p r e s s t h e button once on the
transmitter. The parking lights will come on and the LED will flash 3
times to confirm Temporary Stop feature ‘ON’
2 . T u r n t h e i g n i t i o n k e y t o O F F p o s i t i o n . ( T h e e n g i n e w i l l s t a y r u n n i n g . )
3 . T h e e n g i n e w i l l r u n u n t i l t h e p r e - p r o g r a m m e d t i m e e l a p s e d o r s h u t d o w n
input is received.
TIMER START: You must fully understand this feature to operate the
remote start safely. Use caution in using this feature.
This unit can be programmed to start and run the engine every 3 hours.
The engine will run for the programmed run time and then shut down.
IMPORTANT: Timer Start should be used only in open areas, N E V E R start
and run the vehicle in on enclosed space such as a garage or carport.
Three hours timer start: This feature is design for an extreme cold
climate usage. The system will auto start the vehicle every 3 hours, to
prevent engine freezing and hard to start.
MSVMASTER -       - http://www.msvmaster.lv
MSVMASTER -       - http://www.msvmaster.lv

8
A maximum of six cycles can occur.
E N T E R :
1 . P r e s s t h e button once to remote start the vehicle. As soon as the
vehicle is running the parking lights will turn ‘ON’.
2. Immediately press the button then press button. The parking light
will flash (3) times. The siren chirps (3) times. The vehicle is now
programmed to start every (3) hours.
3. Press the brake pedal to stop the vehicle running.
Exit the timer start:
Timer start can be exited manually as follows:
1. Repeat the Enter Steps from above.
Or
1 . M a k e s u r e t h e r e m o t e s t a r t s y s t e m i s n o t o p e r a t i n g t h e e n g i n e .
2. Turn the ignition on. The LED and parking light will flash (4) times. The
siren chirps (4) times.
SHUTDOWN INPUT FOR REMOTE STARTER:
If any of the following conditions exist while the system is operating, the
engine will not start or will shut down immediately:
1 . T h e h o o d i s o p e n e d .
2 . T h e b r a k e p e d a l i s p r e s s e d .
3 . T h e o p t i o n a l r e m o t e s t a r t e n a b l e t o g g l e s w i t c h i s i n t h e O F F p o s i t i o n .
4 . E n g i n e i s o v e r - r e v v e d . { “ T a c h o m e t e r c h e c k i n g t y p e ” o n l y }
5 . T h e p r e - p r o g r a m m e d r u n t i m e ( 5 / 1 0 / 2 0 / 3 0 m i n u t e s ) h a s e l a p s e d .
6 . T r a n s m i t t e r button is pressed.
7 . T h e v e h i c l e r e f u s e d t o s t a r t r u n n i n g a f t e r { 3 } u n s u c c e s s f u l a t t e m p t s .
DISABLING THE REMOTE START SYSTEM: (If Optional toggle switch is
installed)
This feature allows your system’s remote start unit to be temporarily
disabled to prevent the vehicle from being remote started accidentally. This
feature is useful if the vehicle is being serviced or stored in an enclosed
area. To disable the remote start, move the optional remote start enable
toggle switch to the OFF position. Valet mode can also be used.
XT-43LCDTRANSMITTEROPERATION:
L C D R E M O T E C O N T R O L T R A N S M I T T E R :
MSVMASTER -       - http://www.msvmaster.lv
MSVMASTER -       - http://www.msvmaster.lv

9
B A T T E R Y R E P L A C E M E N T :
A1.5VtypeAAAAlkaline
battery powers the Remote
Transmitter. When the power of
the battery weakens a
icon shall be displayed on the
LCD screen. When the old
battery is replaced with a new
one, there will be beep sounds
indicate the power is up.
Note: Press the button two
times when the battery
compartment is empty, and
then insert the new battery.
THE REMOTE LCD ICONS WITH FUNCTION:
Door Lock
Your vehicle doors are
locked.
Door Unlock Your vehicle
doors are unlocked
Note: If the system is interfered by stronger radio
frequency around, sources of high voltage
electric power or such obstacles like tall
buildings and soon, the transmission range
may get shorter as t he s ystem u ses l ow o utp ut
poweredfrequency.
AAA
MSVMASTER -       - http://www.msvmaster.lv
MSVMASTER -       - http://www.msvmaster.lv

1 0
Start Mode
Your vehicle is running ValetMode
All the function shall be
temporarily on hold.
Remote Transmission
You are transmitting the
signal to control unit
In–RangeIndicator
You are within the remote
control range.
Trunk Release Trunk
open. Trunk symbol only.
Low Battery
You have to replace the
battery of remote control.
Vibration Mode
Remote Control vibrates
when the system is
triggered
Ignition On
PowerSaveMode
Save the battery power
Driver paging
Someone is paging you in
front of your vehicle. **
** Press the valet switch in the vehicle with the Ignition OFF to page
the driver carrying the XT-43two-way remote control.
PROGRAM MODE FOR LCD REMOTE CONTROL TRANSCEIVER:
Press and hold all four remote control buttons simultaneously unit
onelongbeepisheard.LCDProgramminghasnowbeenentered.
T r a n s c e i ve r B u t t o n S y s t e m F u n c t i o n R e m a r k
Program Mode - Switching code for 2nd / 1st
Car Operation Press within 5 seconds
Program Mode - Melody / Vibration Mode Press within 5
seconds
Program Mode - Power Save Mode Press within 5
seconds
LCD screen lamp turns on for
5 seconds.
- + Clear the Flash Icon and
Melody Sound Press within 3 seconds
1 . S e c o n d V e h i c l e S e c u r i t y O p e r a t i o n : Your remote transmitter can be
utilized to control a second vehicle’s Auto Page security system. To
MSVMASTER -       - http://www.msvmaster.lv
MSVMASTER -       - http://www.msvmaster.lv

1 1
program the remote control transmitter to a second vehicle, follow the
instructions for Transmitter programming. All programming parameters
are the same except for the following:
For Regular Remote Control Transmitter:
1 . P r i o r t o p u s h i n g a n y b u t t o n o n t h e t r a n s m i t t e r . P r e s s t h e Select II
button first on the standard transmitter.
2 . O n c e I I b u t t o n i s p r e s s e d t h e L E D o n t h e t r a n s m i t t e r w i l l i l l u m i n a t e f o r
3.5 seconds. While the LED is illuminated, press the button for the
function you want to operate on the standard remote transmitter to
control a second vehicle security system.
For 2-way LCD Remote Control Transceiver:
2nd Car Operation: While the “II” icon display on the LCD screen, you can
remote control and communicate with a second Autopage AM frequency
securitysystem.Ithastwoshort“beep”sounds while pressing any button
of the LCD screen transceiver
1 . P r e s s a n d h o l d a l l f o u r r e m o t e c o n t r o l b u t t o n s
simultaneously unit one long beep is heard. LCD
Programming has now been entered.
2. Within 5 seconds press and hold button until two
beeping sounds are heard and the “II” i c o n w i l l
display on the LCD screen to indicate the second
transceiver pin code has been initiated.
3. To exit programming mode, take no action for five
seconds. The remote control will generate two long
beeps to indicate programming mode has been
exited.
Back to first Car Operation:
This will allow you to control and communicate with the first vehicles
security system.
1. Press and hold all four remote control buttons
simultaneously unit one long beep is heard.
Programming has now been entered.
2. Within 5 seconds press and hold button until one
beep sound is heard.
3. To exit programming mode, take no action for five
seconds. The remote control will generate two long
beeps to indicate programming mode has been
exited.
MSVMASTER -       - http://www.msvmaster.lv
MSVMASTER -       - http://www.msvmaster.lv

1 2
Vibration/MelodyMode:
Vibration mode is useful when you are in a noisy place and it is difficult to
hear the beep sound from the remote control. In this mode the unit will
vibrate if your security system is triggered.
1. Press and hold all four remote control buttons
simultaneously until
one long beep is heard.
Programming has now been entered.
2. Within 5 seconds, pressthe
button to select the
mode of vibration or melody, the
icon will
displayed
on the LCD screen to show the LCD
remote transceiver is in vibration mode.
3. To e
xit programming mode, take no action for five
seconds. The remote control will generate two long
beeps to indicate programming mode has been
exited.
Power Save Mode:
While in the power save mode, the LCD remote transceiver will “sleep” until
a button is pushed. This will extend the life of battery. When power save
mode is “ON”, the remote control will wake up periodically to check for
messages from the security module.
1. Press and hold all four remote control buttons
simultaneously unit one long beep is heard.
Programming has now been entered.
2. Within 5 seconds, pressthe button to toggle
“ O n ” o r “O ff ” . T h e r e m o t e w i l l b e e p o n c e f o r “ O n ”,
twice for “Off”. When power save mode is “On”, the
icon on the LCD screens to indicate entry the
“power save mode”
3. To exit programming mode, take no action for five
seconds. The remote control will generate two long
beeps to indicate programming mode has been
exited.
Screen LampON:
Press the button once and the LCD screen lamp will turn on for 5
seconds.
Clear the Flash Icon and Melody Sound:
Cycle the ignition then press the button first, within 3 seconds press
MSVMASTER -       - http://www.msvmaster.lv
MSVMASTER -       - http://www.msvmaster.lv

1 3
and buttons at the same time. It will clear the flash icon and melody
sound on the LCD screen transceiver.
StopTheTriggerMelodySound:
While triggering the alarm the LCD screen will alert the user through
melody sound and flashing trigger icon. Press any button on the LCD
remote transmitter to stop the melody sound.
LIMITED LIFETIME WARRANTY PROVISIONS
( U.S. ,Continental U.S. and Canada Only)
1 . Auto Page, Inc. WARRANTS that this new unit has been thoroughly inspected and
tested at the factory prior to delivery. Your Auto Page equipment is guaranteed for
“life”totheoriginalpurchaser/useroftheequipmentandtheoriginalvehicleinwhichit
was installed by an authorized installer under the following conditions: If the product
proves defective (according to Auto Page's testing) within the first year, the defective
unit may be exchanged or repaired free of charge. “Proof of Purchase” (dated sales
receipt) must accompany all warranty returns; otherwise, your return will be
rejected and sent back.After one (1) year, the purchaser should ship the unit prepaid
to Auto Page with a money order in the amount of $30.00 to covershippingand
handling charges. Note:The product needs to be registered online at time of
installation. www.autopageusa.com
2 . This WARRANTY will be considered void if the equipment has been misused, neglected,
improperly serviced or installed, altered, dropped or damaged by water, contrary to the
Auto Page OPERATIONS MANUAL. Or, if used with accessories not approved by
Auto Page, which may have contributed to the defect. Seenotebelowregarding
productinstallation**.
3 . The purchaser’s remedies under this WARRANTY shall be limited to the repair or
replacement of electronic components only. THE FOLLOWING IS NOT
COVERED: Damages or deterioration to cases, batteries, covers and cabinets; the cost
of repairs, replacement and labor of which shall be borne by the purchaser even if
MSVMASTER -       - http://www.msvmaster.lv
MSVMASTER -       - http://www.msvmaster.lv

1 4
occurring during the WARRANTY period.
4 . Anyequipmentorparts whichare claimedto be defective underthis WARRANTYmust
be sent to the Auto Page Service center with “proof of purchase” at the purchaser’s
expense prior to such return, a Return Authorization Number should be obtained. Auto
Page will return the equipment, charges prepaid. Warranty Service can be provided
through the dealer where the equipment is originally purchased.
5 . Any unexpired WARRANTY shall be applicable to equipment and parts in the
possessionoftheoriginalpurchaseronly.
6 . THIS WARRANTY IS IN LIEU OF ANY AND ALL OTHER WARRANTIES,
EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE.
7 . Auto Page shall not be liable, under the foregoing WARRANTIES or otherwise, for:
Any personal injury of any kind to the purchaser, its employees or agents or anyone
else whomsoever resulting directly or indirectly from the use or presence of the
equipment or parts; Consequential damages of any kind; any inability of the purchaser
tousetheequipment.
**IMPORTANT NOTE: Any damages to the alarm system resulting from an
installation performed by anyone other than a professional installation
technicianauthorizedbyadealerofAutoPagewillvoidtheproduct’slimited
lifetime warranty.
Auto Page Warranty:
You must register your product online at
http://www.autopageusa.com to receive any warranty service.
Please goto thecustomer service tab and select product
registration.
It is the purchaser’s responsibility to register this product
for any future warranty service.
MSVMASTER -       - http://www.msvmaster.lv
MSVMASTER -       - http://www.msvmaster.lv

1 5
Warning: Some batteries may contain Perchlorate
What is Perchlorate? Perchlorate is both a naturally occurring and
manmade contaminant increasingly found in groundwater, surface water
and soil. Most perchlorate manufactured in the U.S. is used as an
ingredient in solid fuel for rockets and missiles. In addition,
perchlorate-based chemicals are also used in the construction of highway
safety flares, fireworks, pyrotechnics, explosives, commonbatteries, and
automobile restraint systems. Perchlorate contamination has been
reported in at least 20 states. Perchlorate greatly impacts human health
by interfering with iodide uptake into the thyroid gland. In adults, the
thyroid gland helps regulate the metabolism by releasing hormones, while
in children; the thyroid helps in proper development. Perchlorate is
becoming a serious threat to human health and water resources.
“PerchlorateMaterial–Specialhandlingmayapply.”
For more information, go to
http://www.dtsc.ca.gov/hazardouswaste/perchlorate/
MSVMASTER -       - http://www.msvmaster.lv
MSVMASTER -       - http://www.msvmaster.lv