Autonomous Smartdesk 2 User manual

Parts
TOOLS REQUIRED
COMPONENTS
HARDWARE

Parts Diagram
Description
Leg
Foot
Crossbar End
Center Rail
Side Bracket
Power Cord
Control Box
Qty
2
2
2
2
2
1
1
No.
1
2
3
4
5
6
7
Description
Noise Dampener Pad
M6x14 Screws
Combo Screws of Cable Tray
M6x10 Screws
ST4.8x19 Wood Screws
Cable Clips
ST3.5x20 Wood Screws
Qty
8
24
4
8
10
10
2
No.
8
9
10
11
12
13
14
3

Step 1
STEP 2
Fully separate the Crossbar Ends
(P3) by using Allen Wrench to
unscrew M6x10.
You will find the Crossbar Center
Rails (P4) inside.
Place the Legs (P1) into the Crossbar
End (P3), line up the frame's and the
leg's screw holes. Firmly secure the
legs using M6x14 screws. You will
need to flip the legs to gain access to
all 4 screws.
4

Step 3
Repeat Step 2 for the other side.
STEP 4
Attach the side bracket to
either side of the frame using 4
M6x14 screws.
5

Step 5
Repeat Step 2 for the other side.
STEP 6
Slide the two Crossbar Center Rails
into the two Crossbar Ends (P3).
Please make sure the slots in the
Center Rails face inward like in the
photo below.
6

Step 7
Attach the feet (P2) onto the legs (P1)
using 4 M6x14 screws (A view).
STEP 8
Attach 8 Noise dampeners to the 8
holes on the frame - 3 for each side
bracket and 2 at the center.
7

Step 9
Line up the side bracket with the
pre-drilled holes facing upwards. Firmly
secure the frame to the table top using
ST4.8x19 wood screws - 3 for each side
bracket and 2 at the center.
STEP 10
Attach the control box to the top
using 2 ST4.8x19 wood screws.
8

Step 11
Attach the cable tray (if any) to the frame
using 4 M6x12 screws for the Cable tray.
Plug cables from the two motors into the
control box.
Plug the power cable into the other side
of control box.
* Note
If you bought a SmartDesk 2, follow
step 12 to 14 for SmartDesk 2 (page
10 - 11).
If you bought a SmartDesk 3, follow
step 12 to 16 for SmartDesk 3 (page
12 - 14).
9

Step 12 of SmartDesk 2
Attach the keypad using 2 ST3.5x20
wood screws.
Step 13 of SmartDesk 2
Plug the cable from the keypad into
the control box and flip the desk.
10

Step 14 of SmartDesk 2
Before plugging the table into the outlet, make sure that:
- The legs are level and set at the lowest position.
- All the screws are tightened, to avoid the desk making noise or wobbling.
Activate the desk by following the next steps:
- Press “Up” and “Down” buttons at the same time until the desk beeps and moves down to the lowest
level.
- Release both buttons, then press only the “Down” button until it shows the exact height desired.
1. Adjust SmartDesk’s height
Press the “Up” or “Down” button to adjust the height of the desk.
2. Program preset buttons
To use the presets on the SmartDesk, please follow these steps:
- Set the desk to the height you like.
- Press the M button until the LED flashes.
- Press the number you want the desk set to.
3. Reset the desk
- Unplug the power cord from the control box.
- Unplug the cable that links the keypad to the control box.
- Plug all the cables in again.
- Do the reset: Press “Up” and “Down” buttons at the same time until the desk beeps and moves down
to the lowest level. Release both buttons, then press only the “Down” button until it shows the exact
height desired.
- Your desk is ready to use.
Operation guide
11

Flip the Desk.
Place the AI controller (comes in a sepa-
rate box) on the table top. Take note of
the direction of the wire coming out of the
AI controller, and ensure it is placed on
the grooved side.
Step 12 of SmartDesk 3
Step 13 of SmartDesk 3
12

Plug the cable from the AI controller into
the control box.
Plug the USB Wi-Fi into the AI controller
as shown in the picture. Either hub is fine.
Step 14 of SmartDesk 3
Step 15 of SmartDesk 3
13

1. Adjust height:
- Tap the “Adjust height” shortcut to sit/stand.
- Tap the 3 dots to see more options and adjust your
preferences by tapping the Edit icon.
- Tap Add to add new height preferences.
2. Order Food:
- Tap the “Order Food” shortcut to directly order the food
displayed on the screen.
- Tap the 3 dots to see more options and select one food
to order for delivery.
- Tap Add to see nearby restaurants, browse their menus
and start ordering.
3. Gestures:
- Download the Gestures app for PC/MAC from
www.autonomous.ai/gestures. Run the program and login
to your Autonomous account to start pairing AI controller
and PC.
- Select See tips for a user guide on using Gestures on AI
controller to control apps on PC.
4. Shortcut Store:
- A place to download additional shortcuts (Request a
ride, Play music, Control lights... ) from the Shortcut Store
to help boost your health and productivity.
Operation guide
Plug the power cable into the AI controller
and plug in the socket.
Step 16 of SmartDesk 3
14