Autonomous SmartDesk Home Edition User manual

All manuals and user guides at all-guides.com

1
2
6
3
4
7
5
8
No. Description Qty
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
1
2
2
8
2
12
4
1
1
1
14
1
2
12
1
1
1
Crossbar Frame
Side Bracket
Foot
M8*16 Screws
Leg
M6*12 Screws
Fixed Foot Pad
Driveshaft
4 mm Hex Allen
5 mm Hex Allen
Wood Screws ST4.8*19
Wood Screws ST3.5*19
Wrench
Noise Canceling Pad
Control Box
Keypad
Power Cord
910 11 12 13 14
All manuals and user guides at all-guides.com

Use the Allen Wrench to loosen eight M6x10 screws on Crossbar Frame (P1).
Slide two Crossbar Ends along Crossbar Rails following the arrow below.
It is unnecessary to separate the Crossbar Frame.
ADJUST TO DESIRED LENGTH
3
All manuals and user guides at all-guides.com

Step 2
Turn the Legs (P5) upside down on their sides.
Place the Crossbar Ends from Step 1 into the Legs following direction as below pictures.
When positioned correctly, the mount tabs of Crossbar Ends will be facing up.
Insert eight M6x12 screws (P6) into Crossbar Ends - 4 for each side.
Flip the Legs to gain access to all screws and firmly secure both legs.
Non-Motor Leg
Crossbar End Crossbar End
Motor Leg
4
All manuals and user guides at all-guides.com

M8 x 16 Screw
Foot Pad
Step 3
Turn the Legs (P5) upside down on their sides.
Place the Crossbar Ends from Step 1 into the Legs following direction as below pictures.
When positioned correctly, the mount tabs of Crossbar Ends will be facing up.
Insert eight M6x12 screws (P6) into Crossbar Ends - 4 for each side.
Flip the Legs to gain access to all screws and firmly secure both legs.
Firmly attach the Feet (P3) onto the Legs assemblies using 4 M8*16 (P4).
5
All manuals and user guides at all-guides.com

Step 4
Turn the Frame assemblies to upright position.
6
Flip over
All manuals and user guides at all-guides.com

Step 5
Motor Leg
Attach two Side Brackets (P2) to either side of the Legs assemblies.
Insert four M6x12 screws (P6) into Side Brackets.
7
M6*12 Screw 4PCS
All manuals and user guides at all-guides.com

Step 6
Place desktop upside down (with the top side of the desktop facing the floor) on a
towel, rug, or blanket to avoid being scratched.
Line up the Side Brackets to the pre-drilled pilot holes on the Top.
Do not attach the frame to the top
This step is for measurement only.
Align all Bracket Holes with Pre-drilled holes on the Top
Bracket Hole
Pre-drilled Hole
8
All manuals and user guides at all-guides.com

M6*10 Screws (8pcs)
Step 7
After measuring step, hand tighten M6x10 Screws to the frame.
NOTE: Do not firmly tighten the Screws since you may need furthur adjustment later.
Align all Bracket Holes with Pre-drilled holes on the Top
9
All manuals and user guides at all-guides.com

All manuals and user guides at all-guides.com

Non-Motor LegMotor Leg Driveshaft
Insert direction
11
All manuals and user guides at all-guides.com

Ensure both Driveshaft and Center Rod are in good condition.
Driveshaft
Left Nut Right Nut Center Rod
12
All manuals and user guides at all-guides.com

Step 8
Slightly loosen the Right Nut by turning it once around.
Do not remove the Right Nut.
Center Rod
Right Nut
Non-Motor Leg
13
All manuals and user guides at all-guides.com

0.2in
Step 9
Pull the Center Rod out and insert it into the Non-Motor Leg.
Non-Motor Leg
Non-Motor Leg
14
All manuals and user guides at all-guides.com

0.2in
Step 10
Push the Center Rod all the way in.
Leave a small gap (about 0.2in) between Center Rod and the Frame far wall for
smooth rotation of the Rod.
Push the Center Rod
through the Bearing
Important: Leave 0.2in gap here
Non-Motor Leg
15
All manuals and user guides at all-guides.com

Step 11
Turn the Left Nut clockwise to remove it from the Driveshaft.
Ensure the Plastic Grommet inside the Left Nut following correct direction.
Plastic
Grommet
Left Nut Driveshaft
16
All manuals and user guides at all-guides.com

Step 12
Correct Direction Wrong Direction
Insert the Left Nut and Plastic Grommet into the Rod on Motor Leg.
Follow the correct direction and avoid wrong position of both Left Nut and Grommet.
Left Nut Grommet Inverse GrommetInverse Left Nut
17
All manuals and user guides at all-guides.com

Step 13
Insert the Driveshaft into the Rod on Motor Leg.
Push the Driveshaft all the way in.
Motor Leg
18
All manuals and user guides at all-guides.com

Step 14
Leave a small gap (about 0.2in) between the Left Nut and the Motor Leg so
they will not block the Driveshaft when it turns.
Turn the Left Nut counterclockwise to firmly lock the Driveshaft in place.
Motor Leg
19
All manuals and user guides at all-guides.com

Step 15
Turn the Right Nut to lock the Driveshaft in place.
Do not let the Right Nut touch the Frame.
Leave some space
between the Right Nut
and Non-Motor Leg
Non-Motor Leg
20
All manuals and user guides at all-guides.com