Avantco A36505 User manual

Tilt adapter 90°
2018 1
Operator's Manual for Attachment
Tilt adapter 90°
Product number:
A36505
English
A432535 2018 1 EN 2017-
www.avanttecno.com

Tilt adapter 90° 2018 1

Tilt adapter 90° 2018 1
CONTENTS
1. FOREWORD ............................................................................................................................................4
Warning symbols used in this manual ............................................................................................................................... 5
2. DESIGNED PURPOSE OF USE.............................................................................................................6
3. SAFETY INSTRUCTIONS FOR USING THE ATTACHMENT........................................................7
4. TECHNICAL SPECIFICATIONS ..........................................................................................................11
4.1 Safety labels and main components of the attachment.................................................................................. 11
5. ASSEMBLING THE ATTACHMENT....................................................................................................13
5.1 Assembling an attachment to the tilt adapter ................................................................................................. 15
5.2 Connecting and disconnecting hydraulic hoses............................................................................................... 15
5.2.1 Connecting the multiconnector system ................................................................................................... 16
5.2.2 Connecting conventional quick couplings (extra hydraulics outlet of loader) ................................. 16
5.2.3 Disconnecting hydraulic couplings............................................................................................................. 17
6. INSTRUCTIONS FOR USE....................................................................................................................18
6.1 Checks before use................................................................................................................................................. 19
6.2 Using the tilt adapter ............................................................................................................................................ 20
6.3 Maximum load........................................................................................................................................................ 21
6.4 Vertical adjustment ............................................................................................................................................... 22
6.5 Extra auxiliary hydraulics outlet (optional extra for loaders)...................................................................... 24
6.6 Transport position ................................................................................................................................................ 25
6.7 Uncoupling and storage........................................................................................................................................ 25
6.7.1 Storage............................................................................................................................................................. 26
6.7.2 Storage with attachment.............................................................................................................................. 26
7. MAINTENANCE AND SERVICE ..........................................................................................................27
7.1 Inspection of hydraulic components.................................................................................................................. 27
7.2 Cleaning the attachment ...................................................................................................................................... 28
7.3 Lubrication .............................................................................................................................................................. 28
7.4 Inspection of metal structures............................................................................................................................ 28
8. WARRANTY TERMS..............................................................................................................................29

4 (32)
1. Foreword
Avant Tecno Oy would like to thank you for your purchase of this attachment for your Avant loader. It has
been designed and manufactured based on years of experience on product development and manufacturing.
By familiarising yourself with this manual and following the instructions, you ascertain your safety and ensure
the reliable operation and long service life of the equipment. Read the instructions carefully before starting to
use the equipment or performing maintenance.
The purpose of this manual is to help you to:
operate the equipment in a safe and efficient manner
observe and prevent any hazardous situations
keep the equipment intact and ensure a long service life
With these instructions, even an inexperienced user can use the attachment and loader safely. The manual
includes important instructions for experienced AVANT operators as well. Ensure that all persons using the
loader have received proper guidance and familiarised themselves with the manual of the loader, each
attachment that are used, and all safety instructions before using the equipment. Using the equipment for
other purposes or use in any other way than described in this manual is prohibited. Keep this manual at hand
throughout the service life of the equipment. If you sell or transfer the equipment, be sure to hand over this
manual to the new owner. If the manual is lost or damaged, you can request a new one from your Avant
dealer or from the manufacturer.
In addition to the safety instructions included in this manual, you must observe all occupational safety
regulations, local laws, and other regulations concerning the use of the equipment. Particularly the regulations
concerning the use of the equipment on public road areas must be observed. Contact your Avant dealer for
more information about local requirements before you operate the loader on road areas.
Contact your local AVANT dealer for any questions, service, spare parts or about any problems that may
occur with the operation of your machine.
This manual contains the original instructions in English. Due to continuous product development some of the
details shown in this manual may differ from your equipment. Pictures may also depict optional equipment or
features that are not currently available. We reserve the right to change the contents of the manual without
notification. Copyright © 2018 Avant Tecno Oy. All rights reserved.

5 (32)
.
Warning symbols used in this manual
The following warning symbols are used throughout this manual. They indicate factors that must be taken into
account to reduce the risk of personal injury or damage to property:
WARNING SAFETY ALERT SYMBOL
This symbol means: “Warning, be alert! Your safety is involved!”
Carefully read the message that follows, it warns of an immediate hazard
that could cause serious personal injury.
The safety alert symbol by itself and with related safety statement
indicates important safety messages throughout this Manual. It is used to
draw attention to instructions involving your personal safety or the safety
of others. When you see this symbol, be alert, your safety is involved,
carefully read the message that follows, and inform other operators.
DANGER
This signal word indicates a hazardous situation which, if not avoided, will cause
death or serious injury.
WARNING
This signal word indicates a potentially hazardous situation which, if not avoided,
could cause serious injury or death.
CAUTION
This signal word is used when minor injury could result if the instructions are not
followed properly.
This signal word
indicates information about the correct operation and maintenance
of the equipment.
Failure to observe the instructions accompanying the symbol can lead to equipment
breakdown or other property damage.

6 (32)
2. Designed purpose of use
The AVANT Tilt adapter 90° is an attachment suitable for use with AVANT multi purpose loaders shown in
Table 1. A tilt adapter makes it possible to tilt an attachment sideways in both directions. The tilt adapter adds
flexibility and accuracy to work for example in landscaping work, or when working on uneven surfaces with a
bucket or leveller, and when using the pallet forks in inclined terrains.
The tilt adapter is mounted to the loader like other attachments, between the quick coupling plate of the loader
and the attachment that is going to be used. The tilting is controlled with the hydraulics of the loader. The
maximum tilting angle is 45 degrees in both directions, with maximum of 90 degree rotation. It is possible to
set the tilt adapter to tilt full 90 degrees to the right, tilting the attachment to a vertical position. The tilt adapter
may also be left mounted to an attachment, if the tilting function is needed only with a specific attachment. The
tilt adapter is intended mainly for non-hydraulically operated attachments, but when the loader is equipped
with the optional second auxiliary hydraulic outlets in the front, it is possible to use also hydraulically driven
attachments at the same time with the tilt adapter. Suitable hydraulic attachments are e.g. 4 in 1 bucket, pallet
fork with hydraulic fork adjustment, grabbing tool, or artificial turf attachment.
It is recommended to use the tilt adapter with 400-700 series loaders only. Using a tilt adapter moves the
attachment further away from the loader, and thus reduces the tipping load of the loader. When using the tilt
adapter with a heavy attachment, the loader may tip over as a result of displacement of the centre of gravity.
For the best possible stability of the loader, use a tilt adapter only when it is needed for specific tasks, and
uncouple the tilt adapter when it is not needed. The Tilt adapter is not designed for any other use than what is
specified in this manual and must not be used for any other purposes than intended.
The attachment has been designed to require as little maintenance as possible. The operator can perform
regular maintenance tasks. All repair work can’t be performed by the operator, and demanding repair and
maintenance operations are to be left for professional maintenance. All maintenance work must be done using
proper safety equipment. Spare parts must be identical with original specifications, which can be ensured by
using only original spare parts. A separate spare parts catalogue may be available, consult your Avant dealer.
Familiarise yourself with the manual's instructions regarding service and maintenance. Please contact your
AVANT retailer if you have additional questions about the operation or maintenance of the equipment, or if
you require spare parts or maintenance services.
Table 1 - Tilt adapter 90° - Compatibility with Avant loaders
Model
220
225
225LPG
313S
320S
420
423
520
523
R20
525LPG
R28
528
530
630
R35
635
640
745
750
755i
760i
e5
e6
A36505 (•) (•) •••••
It is recommended to use the attachment only with loaders marked with •in Table 1. When using with models
marked with (•), full performance may not be achieved. Additional counterweights may also be required. For
compatibility with a model not shown in table, contact your Avant dealer.

7 (32)
3. Safety instructions for using the attachment
Please bear in mind that safety is the result of several factors. The loader-attachment combination is highly
powerful and improper or careless use or maintenance may cause serious personal injury or property
damage. Due to this, all operators must carefully familiarise themselves about correct use and the operator's
manuals of both the loader and the attachment before starting operation. Do not use the attachment if you
have not completely familiarised yourself with its operation and the related hazards.
DANGER
Misuse, careless use, or using an attachment that is in poor condition, may
cause risk of serious injuries.
Familiarise yourself with the controls of the loader,
correct coupling procedure, and the correct way to operate the attachment a
t a safe
area. Study especially how to stop the equipment in a safe manner. Read all safety
precautions carefully.
Read all safety instructions carefully before handling the attachment
WARNING
Risk of dropping of attachment - Never lift or move an unlocked attachment.
When attaching an attachment to the loader,
ensure that the locking pins of the
loader's quick attach plate are in the lower position and that they have locked
the attachment to the loader.
Make sure attachment is securely connected to
the tilt adapter. Always refer also to
the operator's manual of the separate attachment.
Risk of injuries to other persons -
Do not let others near the danger area of the
equipment when it is in use.
The tilt adapter and any attachment coupled to it are
de
signed to be used by one operator at a time. See additional information about
danger areas of each attachment from the operator's manual of each attachment.
Increased risk of tipping over - Tilt adapter reduces the tipping load of the
loader. Tilt adapt
er moves the attachment further away from the loader, which
reduces the load handling capability of the loader. On inclined terrain the loader can
tip or roll over more easily. Tilt an attachment carefully while keeping the attachment
close to the ground.
It may not be possible to safely tilt an attachment or load on an
inclined surface. Use the tilt adapter only when necessary. Unnecessary use should
be avoided as it increases the risk of tipping over.
Always transport the attachment as low as possible to
keep the centre of gravity low,
and keep the telescopic boom of the loader completely retracted during driving.
Increased risk of roll-over - Transport any load or attachment while keeping the
tilt adapter at its middle position. Tilted attachment can c
ause the loader to roll
over (turn over to its side) during transporting a load. Always keep loads as low as
possible, keep the telescopic boom retracted, and keep the tilt adapter in its middle
position.
Keep the loader articulation in straight position when handling heavy loads. When
turning the articulation, the loader may tilt forward
Do not leave the driver’s seat when the loader boom is lifted. Going under a raised
attachment or loader boom is dangerous. Always remember that the boom may lower
due to loss of stability, mechanical fault, or if another person operates the controls of
the loader.

8 (32)
WARNING
Risk of dropping of load or parts of attachments - Make sure load is secured on
the attachment, and that the attachment is set up properly. Make sure t
hat a load
will not fall uncontrollably off from the attachment. Secure moving parts of the
attachment before using them with a tilt adapter. For example, if using pallet forks,
make sure that the fork arm retainer bolts are fixed so that fork arms will no
t slide off
from the frame of the pallet forks.
Sudden movements can cause the loader to tip over - Operate the controls of
the loader in a slow and calm manner.
Be careful when lifting load to high level or
lifting load from high. Avoid sudden changes
in speed or direction to maintain
balance of the loader especially when handling heavy loads. Drive slowly and
carefully especially on inclined terrain or slippery surfaces.
Make sure that overhead clearance is sufficient. Hitting an overhead obstacle may
cause the loader to tip over. Keep a safe distance from electric cables, lamps, or
other electric systems; hitting live parts may cause electric shock.
Never leave the driver’s seat when the auxiliary hydraulics control lever is locked on.
Also the
tilt adapter may be tilted, if the auxiliary hydraulics control lever of the loader
is locked on and there is a horizontally uneven load on the attachment. Watch out for
crushing of limbs when going near the attachment.
Use the attachment only for its intended use and only with original tools and spare
parts.
When unlocking and dismounting the attachment off from the loader, ensure that it is
secured against accidental movement. To secure the attachment from tipping over
lower it firmly on the ground
and disconnect only on level surface. Ensure the
attachment is properly supported during storage. Never climb on the attachment.
Make sure that the attachment is properly supported before performing any
inspections, maintenance, or adjustments. If nece
ssary, secure the attachment with
suitable lifting equipment, or lower it on firm blocks of wood, for example.
Shut down the loader and place the attachment to a safe position as shown in Safe
stopping procedure before any cleaning, maintenance, or adjustments.
Pay attention to the surroundings and any other persons and machines moving in the
vicinity. Pay attention to the contours of the terrain and other hazards, such as
branches and trees that can reach to the driver's area, loose rocks, and slippe
ry
surfaces.
Make sure to use only an attachment that is in good condition. Do not modify the
attachment in any way that could affect its safety.
Use the attachment only for its intended purpose. Other use may create unnecessary
safety risks, and the equipment may get damaged.
Make sure that the loader is equipped with necessary safety components, and that
they are in working condition. Seat belt must be used. If there are specific hazards
related to the operating area, use appropriate safety equipment.
Also read the safety instructions and correct use of the loader from the operator's
manual of the loader.

9 (32)
DANGER
Wrong, improper, or careless use of the attachment causes serious risk of severe
injuries or death. Familiarise yourself with th
e controls of the loader in a safe area. Pay
particular attention to the safe stopping of the attachment and the loader; follow the safe
stopping procedure shown in this manual before leaving the driver's seat.
WARNING
Using a tilt adapter increased risks of tipping over and roll over -
Use the tilt
adapter only when necessary to complete specific tasks.
Tilt adapter moves the
attachment further away from the loader, which increase the risk of tipping over. Also,
tilting an attachment sideways can cause the loader to roll over (turn over to its side). Use
the tilt adapter only when necessary. Uncouple tilt adapter when it is not needed.
WARNING
Risk of crushing -
Never allow anyone to get under a
lifted attachment or loader boom. Keep in mind t
hat the
loader boom can be lowered or tilted even if the engine has
been shut down (crushing hazard). The loader is not intended
to be left to keep a load elevated for longer periods. Always
lower the attachment to a safe position before leaving the
driver's seat.
WARNING
Risk of crushing - Prevent the attachment from tipping over.
Make sure the load on
the attachment or the moving parts of an attachment will not fall or swing when tilting the
attachment with the tilt adapter.

10 (32)
.
Remember to wear proper personal protective equipment:

The noise level at the driver's seat may exceed 85 dB(A) depending on loader
model and operating cycle. Extended exposure to loud noise can cause
hearing impairment. Wear hearing protection while working with the loader.
Wear protective gloves.
Wear safety boots whenever working with the loader.
Wear safety glasses e.g. when handling hydraulic components.
. ..
Safe stopping of the attachment, before going near the attachment:
WARNING
Always stop
the attachment following safe stopping procedure before leaving
the driver's seat.
Safe stopping procedure prevents all unintentional movements of
the attachment. Note that the loader boom can move down even if the engine of the
loader is turned off. Safe stopping procedure:
Lower the boom and the attachment on the ground.
Shut down the loader engine and lock the parking brake.

Release residual pressure from the hydraulic system; move all hydraulic control
levers to their extreme positions a couple of times.
Prevent starting of the machine, remove ignition key.

11 (32)
4. Technical specifications
Table 2 - Tilt adapter 90° - Specifications
Product number A36505
Max tilt: ±45° or 90° to the right
Weight: 90 kg
Attachment displacement: 147 mm
Maximum load: 1200 kg
Compatible Avant loaders: See Table 1 on page 2
. ..
4.1 Safety labels and main components of the attachment
Listed below are the labels and markings on the attachment. They must be visible and readable on the
equipment. Replace any unclear or missing label. New labels are available via your retailer or contact
information provided on the cover.
WARNING
Make sure all warning decals are readable.
The warning labels contain important
safety information and they help to identify
and remember the hazards related to the
equipment. Replace damaged or missing warning labels with new ones.
Attachment identification plate
A419945
A46771 A46772 A46803
To apply a new label: Clean the surface thoroughly to remove all grease. Allow it to dry completely. Peel off
the protective film of the label and press firmly to apply. Take care not to touch the glue of the label.

12 (32)
.
Table 3 - Decal locations and warning messages
Decal Warning message
1 A36771 Misuse hazard - Read instructions before
use.
2 A36772
Crushing hazard - Do not go under a
raised attachment; stay away from raised
equipment.
3 A36803
Pinching and cutting hazard, keep clear
of moving parts, do not leave the
equipment running. Operate the
attachment only from the driver’s seat.
4 A419945 Attachment identification plate
. ..
. ..
Table 4 - Tilt adapter 90° - Main components
1 Quick attach plate
2
Attachment coupling plate to couple an
attachment to the tilt adapter
3 Locking pins
to lock an attachment to the tilt
adapter
4 Tilting cylinder
5 Tilt arm
6 Center bearing

13 (32)
5. Assembling the attachment
Attaching the attachment to the loader is quick and easy, but it must be done carefully. The attachment is
mounted to the loader boom by using the quick attach plate on the loader boom and the counterpart on the
attachment.
If the attachment is not locked to the loader, it may detach from the loader and cause a hazardous situation.
The loader must not be driven and the boom must never be lifted when the attachment has not been locked.
To prevent hazardous situations, always follow the coupling procedure shown below. Also remember the
safety instructions shown in this manual. The attachment is mounted to the loader as follows:
WARNING
Crushing risk - Make sure that an unlocked attachment will not move or fall over.
Do not stay in the area between the attachment and the loader. Mount the attachment
only on level surface.
Never move or lift an attachment that has not been locked.
Avant quick coupling system:
Step 1:

Lift the quick attach plate locking pins up and turn them backwards into the slot
so that they are locked in the upper position.

If your loader is equipped with a hydraulic attachment locking system, see
additional in
structions about the use of the locking system from the relevant
manuals.
Ensure that the hydraulic hoses are not in the way during installation.
Step 2:
Turn the quick attach plate hydraulically to an obliquely forward position.
Drive the loader ont
o the attachment. If your loader is equipped with a
telescopic boom, you can utilise this.

Align the upper pins of the loader’s quick coupling plate so that they are under
the corresponding brackets of the attachment.
Step 3:
Lift the boom slightly –
pull the boom control lever backward to raise the
attachment off the ground.

Turn the boom control lever left to turn the bottom section of the quick attach
plate onto the attachment.
Lock the locking pins manually or lock the hydraulic locking.
Always check the locking of both locking pins.

14 (32)
WARNING
Risk of crushing - Avoid tipping over the attachment.
Excessive tilting or lifting of an
unlocked attachment increases the risk of tipping the attachment over. Do not use the
automatic locking of the loc
king pins when the attachment is lifted more than one meter
from the ground. If the locking pins do not return to the normal position when tilting, do
not tilt or raise the attachment any more. Lower the attachment on the ground and
secure the locking manually.
WARNING
Risk of falling objects -
Prevent dropping of
attachment.
An attachment that has not been completely locked to the
loader may fall on the boom or towards the operator, or
fall under the loader during driving, causing loss of
control of
the loader. Never move or lift an attachment
that has not been locked. Before moving or lifting the
attachment, make sure that the locking pins are in the
lower position and come through the fasteners on the
attachment on both sides.
WARNING
Make sure the loader is compatible with the attachment.
Stability of the loader,
possible overload of the attachment, and compatibility of loader control systems must be
ensured in addition to mechanical compatibility of the attachment. If you use the
a
ttachment with a loader that is not fit to be used with the attachment model you have,
risks include tipping over, damage to attachment due to overload, and risks related to
uncontrolled motion of attachment and its parts. If your loader is not listed in T
able 1 on
page , ask your Avant dealer before using this attachment.

15 (32)
.
5.1 Assembling an attachment to the tilt adapter
Attaching an attachment to the tilt adapter is easiest, when the tilt adapter is first mounted on the quick attach
plate of the loader. After this the attachment can be mounted to the tilt adapter in a similar way as without the
tilt adapter. Ensure that all four locking pins are in the lower position and they have locked securely.
For easy operation, the tilt adapter can be left mounted on the attachment, if it is needed only with a specific
attachment.
5.2 Connecting and disconnecting hydraulic hoses
In standard configuration, the hydraulic hoses of the tilt adapter are connected using the multi connector
system. See information about connecting the multiconnector in this manual.
If you use an attachment that requires hydraulic output from the loader
If you use an attachment that requires hydraulic output from the loader an extra auxiliary hydraulics output
must be installed to the loader. The extra outlet is available as an option for most loader models. Contact your
Avant dealer or nearest Avant service point for more information about the extra hydraulics outlet. See page
24 and the operator's manual of your loader for more information about using the optional extra hydraulics
outlet.
WARNING
Risk of movement of the attachment and ejection of hydraulic oil -
Never connect
or disconnect quick couplings or other hydraulic components while the control
lever of
the auxiliary hydraulics control lever is locked on or if the system is
pressurized.
Connecting or disconnecting the hydraulic couplings while the system is
pressurized may lead to unintended movements of the attachment, or ejection of high-
pressure fluid
, which can cause serious injuries or burns. Follow safe stopping procedure
before disconnecting hydraulics.
Keep all fittings as clean as possible; use the protective caps on both the attachment and
the loader. Dirt, ice, etc. may make using the fi
ttings significantly more difficult. Never
leave the hoses hanging on the ground; place the couplings onto the holder on the
attachment.

16 (32)
5.2.1 Connecting the multiconnector system
Connecting the multiconnector system:
1.
Align the pins of the attachment connector with corresponding
holes of the loader connector. The multiconnector will not connect
if the attachment connector is upside down.
2.
Connect and lock the multiconnector by turning the lever towards
the loader.
The lever should move easily all the way to its locking position. If the lever does not slide smoothly, check the
alignment and position of the connector and clean the connectors. Also shut down the loader and release the
residual hydraulic pressure.
To disconnect the multiconnector system:
Before disconnecting put the attachment down on a solid and even
surface.
1. Switch off the auxiliary hydraulics of the loader.
2.
While pushing unlock button, turn the lever to disconnect the
connector.
3. After ending operation put the multiconnector on its holde
r on the
attachment.
5.2.2 Connecting conventional quick couplings (extra hydraulics outlet of
loader)
If you use an attachment that requires hydraulic output
from the loader an extra auxiliary hydraulics output must be
installed to the loader. The multicon
nector of the tilt adapter
must be replaced with conventional quick couplings. A pair
of quick couplings are shown In the adjacent figure.
Extra hydraulics outlet on loader
The extra hydraulics coupling is a double-acting hydraulic with two fittings. A pair of standard type hydraulic
quick couplings are located at the front of the loader, just below the multiconnector.
Before you connect or disconnect standard couplings,
relieve hydraulic pressure as described on page .
To connect and disconnect the stan
dard couplings,
move the collar at the end of the female fitting

Note that the protective caps on the loader and the
attachment can be fastened to each other during
operation to reduce the accumulation of dirt.
When disconnecting the standard quick couplin
gs a
small amount of oil may drip from the couplings. Wear
protective gloves and have some cloth at hand to keep
the equipment clean.

17 (32)
5.2.3 Disconnecting hydraulic couplings
Disconnect the hydraulic hoses of the tilt adapter and the attachment from the loader, before unlocking the
quick coupling plate of the loader or the tilt adapter.
When uncoupling the attachment, always disconnect the hydraulic couplings before
unlocking the quick attach plate, to prevent hose damage and any oil spills. Reins
tall the
protective caps on the fittings to prevent impurities from entering the hydraulic system.
Disconnecting hydraulic hoses:
Before disconnecting the fittings, lower the attachment to safe position on solid and level surface. Turn the
control lever of the auxiliary hydraulics to its neutral position.
Releasing residual hydraulic pressure:
In case residual pressure is left in the hydraulic system of the attachment, it is often possible to disconnect the
hydraulic couplings, but it may be difficult to connect them the next time. If the fittings will not connect, the
residual pressure must be released by turning the auxiliary hydraulics control lever of the loader, when the
engine is turned off. To make sure that there will not be residual pressure in the hydraulic system of the
attachment, shut down the loader engine and move the auxiliary hydraulics control lever of the loader back
and forth before disconnecting the couplings.

18 (32)
6. Instructions for use
Check the attachment and the operating environment once more before starting to work, and that all obstacles
have been removed from the operating area. Quick inspection of the equipment and the operating area before
use are parts of ensuring safety and the best performance of the equipment.
WARNING
Risk of crushing -
Never allow anyone to get under a
lifted attachment or loader boom.
Keep in mind that the
loader boom can be lowered or tilted even if the engine has
been shut down (crushing hazard). The loader is not intended
to be left to keep a load eleva
ted for longer periods. Always
lower the attachment to a safe position before leaving the
driver's seat.
WARNING
Risk of tipping over - Avoid overload.
Loader can tip over
when handling too heavy loads, or because of dynamic
movements caused by dr
iving with and handling of a heavy
load. Do not extend the telescopic boom when the load
approaches the lifting capacity of the loader, or when the
loader boom is in horizontal position. When you notice that
the rear wheels of the loader are about to lift
from the ground,
or if the load indicator of the loader (if fitted) signals:
Lower the load calmly and retract the telescopic boom
Avoid sudden changes in speed or direction whenever load is lifted
Use additional counterweights as needed
WARNING
Risk of tipping over -
Avoid overload and keep heavy load close to the loader. Keep
loads close to the ground whenever driving, especially during turns and uneven
terrain.
Pay attention that a heavy load or long distance between the loader and the
centre
of gravity of the load will affect the balance and handling of the loader. The use of
additional counterweights is recommended especially when operating smaller loader
models. For 200-
series loader the wheel weights are recommended. With heavy loads,
the
telescopic boom must be kept retracted while moving with the loader. Always wear
seat belt.

19 (32)
6.1 Checks before use
Drive carefully on uneven terrain and note the effect of heavy load at the front of the loader to the
stability and handling of the loader.
Practise the use of the attachment and the controls of the loader in a safe area. If you are unfamiliar
with the particular loader model, it is recommended to practise its use without any attachments.
Check the attachment you are planning to use with tilt adapter according to separate specific
instructions before operating the attachment. Make sure that there are no broken components.
Use only when all pins and hydraulic fittings are locked and secured in place. The locking of the tilt
adapter and the attachment includes a total of four locking pins. Ensure that all four locking pins have
locked securely.
When mounting an attachment onto the tilt adapter, note that the locking pins must always be secured
manually.
Keep the auxiliary hydraulics of the loader at the one pump setting for easier and more accurate
control of the adapter.
Ensure that bystanders are at a safe distance when operating the equipment. Do not let anyone to
enter danger area of the boom or to stay directly in front of the loader. Also make sure that it is safe to
reverse with the loader. Never assume that bystanders will remain where you last saw them;
especially children are often attracted to the moving equipment.
Check the general condition of the attachment and the loader, and check for possible hydraulic oil
leaks. The attachment must not be used, if there is a fault in the hydraulic system of the loader or the
attachment. Refer to Chapter 7 for maintenance instructions.
Operate the attachment and the controls of the loader only when seated on the driver’s seat. Ensure
that the loader and the attachment are used in a safe manner and as intended. Do not allow children
to operate the equipment.
Never operate the loader or attachments while under the influence of alcohol, drugs, medication that
may impair judgement or cause drowsiness, or if not otherwise medically fit to operate the equipment.
Remember correct working methods and avoid leaving the driver’s seat unnecessarily.
WARNING
Avoid running over persons - Check surroundings before driving.
Always look in the
direction the loader is moving. Before reversing, always ensure that bystanders,
especially children, are at a safe distance to avoid back-over accidents.

20 (32)
.
6.2 Using the tilt adapter
Move the auxiliary hydraulics cont
rol
lever of the loader towards its
locking position to turn the
attachment to right.
Stop by releasing the lever to neutral
position.
Move the auxiliary hydraulics control
lever of the loader to reverse
direction to turn the attachment to
left.