Avaya G450 Manager User manual

Configuring V.150.1 on the Avaya G450
Branch Gateway
Issue 1
July 2012

Contents
Chapter 1: Introduction...................................................................................................... 5
V.150.1 requirements................................................................................................................................ 5
Chapter 2: Installing the MP160......................................................................................... 7
Adding and removing the MP160.............................................................................................................. 7
Chapter 3: Configuring V.150.1 in Communication Manager.......................................... 13
Configuring V.150.1................................................................................................................................... 13
IP codec set.............................................................................................................................................. 14
IP codec set: page 2......................................................................................................................... 15
IP codec set: page 3......................................................................................................................... 19
Index..................................................................................................................................... 23
Configuring V.150.1 on the Avaya G450 Branch Gateway July 2012 3

4 Configuring V.150.1 on the Avaya G450 Branch Gateway July 2012

Chapter 1: Introduction
V.150.1 requirements
Important:
V.150.1 and the MP160 Media Processor Module are only for DISA-approved and civilian
US Government sites. Please contact your Avaya Sales team for additional questions.
The requirements are as follows:
• G450 Branch Gateway.
- Hardware version 1.x or 2.x
- Firmware 32.16 or higher
Note:
V.150.1 is not supported on the G430.
• At least one MP160 Media Processor Module installed on the G450 main board. See
Adding and removing the MP160 on page 7 for instructions on installing the MP160.
• Avaya Aura®Communication Manager 6.0.1 load with the JITC Service Pack.
Note:
See the Avaya Support web site http://support.avaya.com/ for details of the Service
Pack
Configuring V.150.1 on the Avaya G450 Branch Gateway July 2012 5

Introduction
6 Configuring V.150.1 on the Avaya G450 Branch Gateway July 2012
Comments? [email protected]

Chapter 2: Installing the MP160
Adding and removing the MP160
Before you begin
The G450 main board has four slots for VoIP engines.You can install up to two MP160 (Media
Processor 160). An MP160 provides 160 channels for voice transport.
Note:
The G450 supports up to 320 active channels for voice transport. You can install up to two
MP160 modules, or a combination of Media Processor modules with a total of up to 320
channels for voice transport, for example, one MP160 and two MP80s.
See the table below for permitted combinations of Media Processor modules:
Combination of
cards MP20 MP80 MP160
Combination #1 - - 1 or 2
Combination #2 1 or 2 - 1
Combination #3 - 1 or 2 1
Combination #4 1 1 1
Important:
You can only install the MP160 in slots 2 and 4 on the G450 1.x or slots 1 and 2 on the G450
2.x. (see Figure 2: Location of MP160 module slots in a G450 1.x on page 9 and Figure
3: Location of MP160 module slots in a G450 2.x on page 10) On the G450 1.x, the ASB
button is to the right of the RST button. On the G450 2.x, the RST button is above the ASB
button.
You can also use the show system command in the command line interface to identify the
mainboard HW vintage (version).
Electrostatic alert:
Hold modules only by the edges to avoid damage from static electricity. Do not touch the
top or bottom of the circuit board. If possible, wear a wrist-strap and use an anti-static
bag.
Configuring V.150.1 on the Avaya G450 Branch Gateway July 2012 7

Caution:
Theconnectorpinscanbebentordamagedifthemoduleishandledroughly,orifmisaligned
and then forced into position.
Caution:
Attach the correct standoff according to the hardware version of the G450. Using the wrong
standoff will prevent you from installing the MP160 correctly.
About this task
You do not need to configure the G450 when you install an MP160. However, you must
configure V.150.1 in Communication Manager. See Configuring V.150.1 on page 13
Procedure
1. Insert the provided plastic standoff in the hole
The standoff type differs depending on the hardware version of the G450. Ensure
you use the correct standoff.
Figure 1: Location of Standoff on MP160
• Use the short standoff For the G450 1.x.
• Use the long standoff for the G450 2.x.
2. Locate the MP160 module slot. The location differs depending on the hardware
version of the G450 (see Figure 2: Location of MP160 module slots in a G450
1.x on page 9 and Figure 3: Location of MP160 module slots in a G450 2.x on
page 10)
Installing the MP160
8 Configuring V.150.1 on the Avaya G450 Branch Gateway July 2012
Comments? [email protected]

Figure 2: Location of MP160 module slots in a G450 1.x
Table 1: Figure notes:
1. MP20 or MP80 module slot
2. MP20,MP80 or MP160 module slot
3. MP20 or MP80 module slot
4. MP20, MP80 or MP160 module slot
Adding and removing the MP160
Configuring V.150.1 on the Avaya G450 Branch Gateway July 2012 9

Figure 3: Location of MP160 module slots in a G450 2.x
Table 2: Figure notes:
1. MP20, MP80 or MP160 module slot
2. MP20, MP80 or MP160 module slot
3. MP20 or MP80 module slot
4. MP20 or MP80 module slot
3. Position the module at a 45 degree angle to the main board, and start inserting it
into the slot.
Installing the MP160
10 Configuring V.150.1 on the Avaya G450 Branch Gateway July 2012
Comments? [email protected]