Avaya 9130 Setup guide

Avaya 9130 1000–3000 VA
Uninterruptible Power Systems
Site Preparation,
Installation and Operator’s Manual
www.powerware.com/avaya

Avaya 9130 1000–3000 VA
Uninterruptible Power Systems
Site Preparation,
Installation and Operator’s Manual
www.powerware.com/avaya

Class A EMC Statements
(Low Voltage Models over 1500 VA)
FCC Part 15
NOTE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
ICES-003
This Class A Interference Causing Equipment meets all requirements of the Canadian Interference Causing
Equipment Regulations ICES-003.
Cet appareil numérique de classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du
Canada, ICES-003.
EN 62040-2
Some configurations are classified under EN 62040-2 as “Class-A UPS for Unrestricted Sales Distribution.” For
these configurations, the following applies:
WARNING This is a Class A-UPS Product. In a domestic environment, this product may cause radio interference, in
which case, the user may be required to take additional measures.
VCCI Notice
Avaya and the Avaya logo are trademarks of Avaya Inc. and may be registered in certain jurisdictions. Powerware,
ABM, and LanSafe are registered trademarks and ConnectUPS is a trademark of Eaton Corporation or its
subsidiaries and affiliates. National Electrical Code and NEC are registered trademarks of National Fire Protection
Association, Inc. Phillips is a registered trademark of Phillips Screw Company. All other trademarks are property of
their respective companies.
ECopyright 2008 Avaya Inc. All rights reserved. No part of this document may be reproduced in any way without
the express written approval of Avaya.

Class B EMC Statements
(Low Voltage Models up to 1500 VA and
High Voltage Models up to 3000 VA)
FCC Part 15
NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
SReorient or relocate the receiving antenna.
SIncrease the separation between the equipment and the receiver.
SConnect the equipment into an outlet on a circuit different from that to which the receiver is connected.
SConsult the dealer or an experienced radio/TV technician for help.
ICES-003
This Class B Interference Causing Equipment meets all requirements of the Canadian Interference Causing
Equipment Regulations ICES-003.
Cet appareil numérique de classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du
Canada, ICES-003.
VCCI Notice

Requesting a Declaration of Conformity
Units that are labeled with a CE mark comply with the following harmonized standards and EU directives:
SHarmonized Standards: IEC 61000-3-12
SEU Directives: 73/23/EEC, Council Directive on equipment designed for use within certain voltage limits
93/68/EEC, Amending Directive 73/23/EEC
89/336/EEC, Council Directive relating to electromagnetic compatibility
92/31/EEC, Amending Directive 89/336/EEC relating to EMC
The EC Declaration of Conformity is available upon request for products with a CE mark. For copies of the EC
Declaration of Conformity, contact:
Eaton Power Quality Oy
Koskelontie 13
FIN-02920 Espoo
Finland
Phone: [phone]
Fax: [phone]
Special Symbols
The following are examples of symbols used on the UPS or accessories to alert you to important
information:
RISK OF ELECTRIC SHOCK - Observe the warning associated with the risk of electric shock
symbol.
CAUTION: REFER TO OPERATOR’S MANUAL - Refer to your operator’s manual for additional
information, such as important operating and maintenance instructions.
This symbol indicates that you should not discard the UPS or the UPS batteries in the trash. This
product contains sealed, lead-acid batteries and must be disposed of properly. For more information,
contact your local recycling/reuse or hazardous waste center.
This symbol indicates that you should not discard waste electrical or electronic equipment (WEEE) in
the trash. For proper disposal, contact your local recycling/reuse or hazardous waste center.

Avaya 9130 1000–3000 VA UPS Site Preparation, Installation and Operator’s Manual S164201765 Rev 1 i
Table of Contents
1 Introduction 1.........................................................
2 Safety Warnings 3.....................................................
3 Installation 17..........................................................
Inspecting the Equipment 17................................................................
Unpacking the Cabinet 18..................................................................
Checking the Accessory Kit 18..............................................................
Installation 19..........................................................................
Checking the Rail Kit Accessories 19.......................................................
Tools Required 19.....................................................................
Rackmount Setup 20...................................................................
Wiring Installation 23.....................................................................
Installing the UPS 23..................................................................
Connecting the EBM(s) 26...............................................................
UPS Initial Startup 29.....................................................................
4 Operation 33...........................................................
Control Panel Functions 33.................................................................
Changing the Language 34..............................................................
Display Functions 34...................................................................
User Settings 36......................................................................
Operating Modes 39.....................................................................
Normal Mode 39.....................................................................
Battery Mode 39.....................................................................
Bypass Mode 40......................................................................
Standby Mode 40.....................................................................
UPS Startup and Shutdown 41..............................................................
Starting the UPS 41...................................................................
Starting the UPS on Battery 42...........................................................
UPS Shutdown 42.....................................................................
Transferring the UPS Between Modes 43.......................................................
Retrieving the Event Log 43................................................................
Setting Power Strategy 43.................................................................
Configuring Bypass Settings 44..............................................................
Configuring Load Segments 45..............................................................

TABLE OF CONTENTS
Avaya 9130 1000–3000 VA UPS Site Preparation, Installation and Operator’s Manual S164201765 Rev 1
ii
Configuring Battery Settings 46..............................................................
Configuring the UPS for EBMs 46..........................................................
Running Battery Tests 47...............................................................
Configuring Automatic Restart 48.........................................................
5 Communication 49......................................................
Installing Communication Options and Control Terminals 50.........................................
Communication Options 50.................................................................
RS-232 and USB Communication Ports 50....................................................
ConnectUPS-BD Web/SNMP Card 52.......................................................
Remote Emergency Power-off 53..........................................................
Relay Output Contacts 54...............................................................
Programmable Signal Inputs 55...........................................................
Modem Operation 57.....................................................................
Powerware LanSafe Power Management Software 57.............................................
6 UPS Maintenance 59....................................................
UPS and Battery Care 59..................................................................
Storing the UPS and Batteries 59............................................................
When to Replace Batteries 60...............................................................
Replacing Batteries 60....................................................................
Replacing UPS Internal Batteries 61........................................................
Replacing EBMs 64....................................................................
Testing New Batteries 66..................................................................
Recycling the Used Battery or UPS 67.........................................................
Updating the UPS Firmware 67..............................................................
7 Specifications 69.......................................................
Model Specifications 69...................................................................
Rear Panels 76.........................................................................
8 Troubleshooting 79......................................................
Typical Alarms and Conditions 79............................................................
Silencing the Alarm 83....................................................................
Obtaining Service 83.....................................................................
Parts List 83...........................................................................

Avaya 9130 1000–3000 VA UPS Site Preparation, Installation and Operator’s Manual S164201765 Rev 1 1
Chapter 1 Introduction
The Avaya®9130 uninterruptible power system (UPS) protects your
sensitive electronic equipment from the most common power problems,
including power failures, power sags, power surges, brownouts, line
noise, high voltage spikes, frequency variations, switching transients,
and harmonic distortion.
Power outages can occur when you least expect it and power
quality can be erratic. These power problems have the potential to
corrupt critical data, destroy unsaved work sessions, and damage
hardware — causing hours of lost productivity and expensive repairs.
With the Avaya 9130, you can safely eliminate the effects of power
disturbances and guard the integrity of your equipment. Providing
outstanding performance and reliability, the Avaya 9130’s unique
benefits include:
STrue online double-conversion technology with high power density,
utility frequency independence, and generator compatibility.
SRackmount models in a space-optimizing 2U size that fits any
standard 48 cm (19”) rack.
SABM®technology that uses advanced battery management to
increase battery service life, optimize recharge time, and provide a
warning before the end of useful battery life.
SSelectable High Efficiency mode of operation.
SEmergency shutdown control through the Remote Emergency
Power-off (REPO) port.
SNetwork power management with the ConnectUPS -BD Web/SNMP
Card. This internal card has SNMP and HTTP capabilities as well as
monitoring through a Web browser interface; connects to a
twisted-pair Ethernet (10/100BaseT) network.
SAdditional communication options: one RS-232 communication port,
one USB communication port, and relay output contacts.
SOptional modem capability for remote monitoring and service.
SExtended runtime with Extended Battery Modules (EBMs).
SFirmware that is easily upgradable without a service call.
SBacked by worldwide agency approvals.
t

INTRODUCTION
Avaya 9130 1000–3000 VA UPS Site Preparation, Installation and Operator’s Manual S164201765 Rev 1
2
Figure 1 shows the Avaya 9130 UPS, and Figure 2 shows the optional
EBM.
Figure 1. The Avaya 9130 UPS
Figure 2. The Avaya 9130 EBM

Avaya 9130 1000–3000 VA UPS Site Preparation, Installation and Operator’s Manual S164201765 Rev 1 3
Chapter 2 Safety Warnings
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
This manual contains important instructions that you should follow during installation and
maintenance of the UPS and batteries. Please read all instructions before operating the
equipment and save this manual for future reference.
DANGER
This UPS contains LETHAL VOLTAGES. All repairs and service should be performed by
AUTHORIZED SERVICE PERSONNEL ONLY. There are NO USER SERVICEABLE PARTS
inside the UPS.
WARNING
SThis UPS contains its own energy source (batteries). The UPS output may carry live
voltage even when the UPS is not connected to an AC supply.
STo reduce the risk of fire or electric shock, install this UPS in a temperature and humidity
controlled, indoor environment, free of conductive contaminants. Ambient temperature
must not exceed 40°C (104°F). Do not operate near water or excessive humidity
(90% maximum).
STo reduce the risk of fire, connect only to a circuit provided with branch circuit
overcurrent protection in accordance with the National Electrical Code®(NEC®),
ANSI/NFPA 70.
SOutput overcurrent protection and disconnect switch must be provided by others.
STo comply with international standards and wiring regulations, the sum of the leakage
current of the UPS and the total equipment connected to the output of this UPS must not
have an earth leakage current greater than 3.5 milliamperes.
SIf installing optional rackmount EBM(s), install the EBM(s) directly below the UPS so that
all wiring between the cabinets is installed behind the front covers and is inaccessible to
users. The maximum number of EBM(s) per UPS is four.
SIf the UPS requires any type of transportation, verify that the UPS is unplugged and
turned off and then disconnect the UPS internal battery connector (see Figure 20 on
page 62).

SAFETY WARNINGS
Avaya 9130 1000–3000 VA UPS Site Preparation, Installation and Operator’s Manual S164201765 Rev 1
4
CAUTION
SBatteries can present a risk of electrical shock or burn from high short-circuit current.
Observe proper precautions. Servicing should be performed by qualified service
personnel knowledgeable of batteries and required precautions. Keep unauthorized
personnel away from batteries.
SProper disposal of batteries is required. Refer to your local codes for disposal
requirements.
SNever dispose of batteries in a fire. Batteries may explode when exposed to flame.
Sikkerhedsanvisninger
VIGTIGE SIKKERHEDSANVISNINGER
GEM DISSE ANVISNINGER
Denne manual indeholder vigtige instruktioner, som skal følges under installation og
vedligeholdelse af UPS’en og batterierne. Læs venligst alle instruktioner inden betjening af
udstyret og gem denne manual mhp. fremtidige opslag.
FARE
Denne UPS indeholder LIVSFARLIG HØJSPÆNDING. Alle reparationer og vedligeholdelse bør
kun udføres af en AUTORISERET SERVICETEKNIKER. Ingen af UPS’ens indvendige dele kan
repareres af brugeren.
ADVARSEL!
SDenne UPS indeholder sin egen energikilde (batterier). Udgangsstikket på UPS’en kan
endog være strømførende, når UPS’en ikke er koblet til en vekselstrømsforsyning.
SInstallér denne UPS i et temperatur- og fugtighedskontrolleret indendørsmiljø, frit for
ledende forureningsstoffer for at formindske risikoen for brand og elektrisk stød.
Rumtemperaturen må ikke overstige 40°C. UPS’en bør ikke betjenes nær vand eller høj
fugtighed (maksimalt 90%).
SFor at reducere risikoen for brand må tilkobling kun ske til et kredsløb forsynet med
100 ampere maks. linieforgrenings overbelastningsbeskyttelse i overensstemmelse med
NEC, ANSI/NFPA 70.
SUdgangsoverbelastningsbeskyttelsen og afbryderkontakten skal leveres af andre.
SI overensstemmelse med internationale normer og bestemmelser for el-installation må
det udstyr, der er forbundet til udgangen af denne UPS, tilsammen ikke overskride en
jordafdelingsspænding på mere end 3,5 milliampere.

SAFETY WARNINGS
Avaya 9130 1000–3000 VA UPS Site Preparation, Installation and Operator’s Manual S164201765 Rev 1 5
ADVARSEL
SBatterierne kan give risiko for elektrisk stød eller brandsår forårsaget af høj
kortslutningsstrøm. Overhold gældende forsigtighedsregler. Servicering skal udføres af
kvalificeret servicepersonale med kendskab til batterier og gældende forsigtighedsregler.
Hold uautoriseret personale væk fra batterierne.
SKorrekt bortskaffelse af batterier er påkrævet. Overhold gældende lokale regler for
bortskaffelsesprocedurer.
SSkaf dig aldrig af med batterierne ved at brænde dem. Batterierne kan eksplodere ved
åben ild.
Belangrijke Veiligheidsinstructies
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
BEWAAR DEZE INSTRUCTIES
Deze handleiding bevat belangrijke instructies die u dient te volgen tijdens de installatie en
het onderhoud van de UPS en de accu’s. Lees alle instructies voordat u de apparatuur in
bedrijf neemt en bewaar deze handleiding als naslagwerk.
GEVAAR
Deze UPS bevat LEVENSGEVAARLIJKE ELEKTRISCHE SPANNING. Alle reparaties en
onderhoud dienen UITSLUITEND DOOR ERKEND SERVICEPERSONEEL te worden uitgevoerd.
Er bevinden zich GEEN ONDERDELEN in de UPS die DOOR DE GEBRUIKER kunnen worden
GEREPAREERD.
WAARSCHUWING
SDeze UPS bevat een eigen energiebron (accu’s). De UPS-uitgang kan onder spanning
staan, zelfs wanneer de UPS niet is aangesloten op de netspanning.
STeneinde de kans op brand of elektrische schok te verminderen dient deze UPS in een
gebouw met temperatuur- en vochtigheidregeling te worden geïnstalleerd, waar geen
geleidende verontreinigingen aanwezig zijn. De omgevingstemperatuur mag 40°C niet
overschrijden. Niet gebruiken in de buurt van water of bij zeer hoge vochtigheid
(max. 90%).
SSluit om brandgevaar te voorkomen de apparatuur uitsluitend aan op een circuit voorzien
van een overstroombeveiliging voor vertakte circuits van maximaal 100 A in
overeenstemming met de NEC (Nationale Elektriciteitsvoorschriften), ANSI/NFPA 70.

SAFETY WARNINGS
Avaya 9130 1000–3000 VA UPS Site Preparation, Installation and Operator’s Manual S164201765 Rev 1
6
SDe uitgangsoverstroombeveiliging en de stroomonderbreker moeten door derden worden
geleverd.
SOm aan de internationale normen en bedradingsvoorschriften te voldoen mag de gehele
apparatuur die op de uitgang van deze UPS is aangesloten, geen aardlekstroom van
meer dan 3,5 milliampère hebben.
OPGELET
SBatterijen leveren gevaar op voor elektrische schokken en kunnen brandwonden
veroorzaken door een grote kortsluitstroom. Neem de juiste voorzorgsmaatregelen in
acht. Het onderhoud moet worden uitgevoerd door bevoegde onderhoudsmonteurs die
verstand hebben van accu’s en op de hoogte zijn van de vereiste voorzorgsmaatregelen.
Houd onbevoegden uit de buurt van de accu’s.
SDe batterijen moeten op de juiste wijze worden opgeruimd. Raadpleeg hiervoor uw
plaatselijke voorschriften.
SNooit batterijen in het vuur gooien. De batterijen kunnen ontploffen.
Tarkeita Turvaohjeita
TÄRKEITÄ TURVAOHJEITA - SUOMI
SÄILYTÄ NÄMÄ OHJEET
Tämä käyttöohje sisältää tärkeitä ohjeita, joita on noudatettava UPS-virtalähteen ja akkujen
asennuksen ja huollon yhteydessä. Lue kaikki ohjeet ennen laitteiston käyttöä ja säilytä ohje
myöhempää tarvetta varten.
VAARA
Tämä UPS sisältää HENGENVAARALLISIA JÄNNITTEITÄ. Kaikki korjaukset ja huollot on
jätettävä VAIN VALTUUTETUN HUOLTOHENKILÖN TOIMEKSI. UPS ei sisällä MITÄÄN
KÄYTTÄJÄN HUOLLETTAVIA OSIA.
VAROITUS
STässä UPS-virtalähteessä on oma energianlähde (akut). UPS-virtalähteen lähdössä voi
olla jännite, vaikka UPS-virtalähdettä ei ole kytketty verkkovirtaan.
SVähentääksesi tulipalon ja sähköiskun vaaraa asenna tämä UPS sisätiloihin,
joissa lämpötila ja kosteus on säädettävissä ja joissa ei ole virtaa johtavia
epäpuhtauksia. Ympäristön lämpötila ei saa ylittää 40 °C. Älä käytä lähellä vettä ja vältä
kosteita tiloja (95 % maksimi).

SAFETY WARNINGS
Avaya 9130 1000–3000 VA UPS Site Preparation, Installation and Operator’s Manual S164201765 Rev 1 7
SPienennä tulipalon vaaraa kytkemällä vain piiriin, jossa on 100 ampeerin
maksimihaarapiirin ylivirtasuoja kansallisen sähkölainsäädännön (ANSI/NFPA 70)
mukaan.
SMuiden on toimitettava lähdön ylivirtasuoja ja irtikytkentäkytkin.
SKansainväliset normit ja johdotusmääräykset vaativat, että kaikkien tämän UPS-laitteen
ulostulokytkentöjen yhteinen maavuotovirta ei ylitä 3,5 milliampeeria (mA).
VARO
SAkut voivat aiheuttaa sähköiskun tai palovammojen vaaran johtuen suuresta
oikosulkuvirrasta. Noudata kaikkia asianmukaisia varotoimia. Laitteen saa huoltaa vain
ammattitaitoinen huoltohenkilökunta, joka tuntee akut ja niihin liittyvät varotoimet. Älä
päästä valtuuttamatonta henkilöstöä lähelle akkuja.
SAkusto täytyy hävittää säädösten mukaisella tavalla. Noudata paikallisia määräyksiä.
SÄlä koskaan heitä akkuja tuleen. Ne voivat räjähtää.
Consignes de sécurité
CONSIGNES DE SÉCURITÉ IMPORTANTES
CONSERVER CES INSTRUCTIONS
Ce manuel comporte des instructions importantes que vous êtes invité à suivre lors de toute
procédure d’installation et de maintenance des batteries et de l’onduleur. Veuillez consulter
entièrement ces instructions avant de faire fonctionner l’équipement et conserver ce manuel
afin de pouvoir vous y reporter ultérieurement.
DANGER!
Cet onduleur contient des TENSIONS MORTELLES. Toute opération d’entretien et de
réparation doit être EXCLUSIVEMENT CONFIÉE A UN PERSONNEL QUALIFIÉ AGRÉÉ.
AUCUNE PIÈCE RÉPARABLE PAR L’UTILISATEUR ne se trouve dans l’onduleur.
AVERTISSEMENT!
SCette onduleur possède sa propre source d’alimentation (batteries). Il est possible que la
sortie de l’onduleur soit sous tension même lorsque l’onduleur n’est pas connectée à une
alimentation CA.
SPour réduire les risques d’incendie et de décharge électrique, installer l’onduleur
uniquement à l’intérieur, dans un lieu dépourvu de matériaux conducteurs, où la
température et l’humidité ambiantes sont contrôlées. La température ambiante ne doit
pas dépasser 40 °C. Ne pas utiliser à proximité d’eau ou dans une atmosphère
excessivement humide (95 % maximum).

SAFETY WARNINGS
Avaya 9130 1000–3000 VA UPS Site Preparation, Installation and Operator’s Manual S164201765 Rev 1
8
SAfin de réduire les risques d’incendie, ne raccordez qu’à un circuit muni d’une protection
de surintensité du circuit de dérivation maximum de 100 ampères conformément au NEC
(Code Électrique National) des États-Unis, ANSI/NFPA 70.
SLa protection de surintensité de sortie ainsi que le sectionneur doivent être fournis par
des tiers.
SAfin d’être conforme aux normes et règlements internationaux de câblage, le courant de
fuite à la terre de la totalité du matériel branché sur la sortie de l’onduleur ne doit pas
dépasser 3,5 mA.
ATTENTION!
SLes batteries peuvent présenter un risque de choc électrique ou de brûlure provenant
d’un courant de court-circuit haute intensité. Observez les précautions appropriées.
L’entretien doit être réalisé par du personnel qualifié connaissant bien les batteries et
les précautions nécessaires. N’autorisez aucun personnel non qualifié à manipuler les
batteries.
SUne mise au rebut réglementaire des batteries est obligatoire. Consulter les règlements
en vigueur dans votre localité.
SNe jamais jeter les batteries au feu. L’exposition aux flammes risque de les faire
exploser.
Sicherheitswarnungen
WICHTIGE SICHERHEITSANWEISUNGEN
AUFBEWAREN
Dieses Handbuch enthält wichtige Anweisungen, die Sie während der Installation und
Wartung des USV (Unterbrechungsfreies Stromversorgungssystem) und der Batterien
befolgen müssen. Bitte lesen Sie alle Anweisungen des Handbuches bevor sie mit dem
Gerät arbeiten. Bewaren Sie das Handbuch zum Nachlesen auf.
WARNUNG
Die USV führt lebensgefährliche Spannungen. Alle Reparatur- und Wartungsarbeiten sollten
nur von Kundendienstfachleuten durchgeführt werden. Die USV enthält keine vom Benutzer
zu wartenden Komponenten.

SAFETY WARNINGS
Avaya 9130 1000–3000 VA UPS Site Preparation, Installation and Operator’s Manual S164201765 Rev 1 9
ACHTUNG
SDieses USV (Unterbrechungsfreies Stromversorgungssystem) enthält eine eigene
Energiequelle (Batterien). Der USV-Ausgang kann Spannung führen, auch wenn das USV
nicht an eine Wechselstromquelle angeschlossen ist.
SUm die Brand- oder Elektroschockgefahr zu verringern, diese USV nur in Gebäuden mit
kontrollierter Temperatur und Luftfeuchtigkeit installieren, in denen keine leitenden
Schmutzstoffen vorhanden sind. Die Umgebungstemperatur darf 40°C nicht übersteigen.
Die USV nicht in der Nähe von Wasser oder in extrem hoher Luftfeuchtigkeit (max. 95 %)
betreiben.
SUm die Brandgefahr zu verringern, nur an eine Leitung anschließen, die mit einem
Überlaststromschutz von maximal 100 Ampere in Übereinstimmung mit dem NEC,
ANSI/NFPA 70 ausgestattet ist.
SDer Ausgangs-Überlaststromschutz und der Trennschalter müssen von anderen
Herstellern geliefert werden.
SUm internationale Normen und Verdrahtungsvorschriften zu erfüllen, dürfen die an den
Ausgang dieser USV angeschlossenen Geräte zusammen einen Erdableitstrom von
insgesamt 3,5 Milliampere nicht überschreiten.
VORSICHT!
SBatterien können das Risiko eines elektrischen Schlags bergen oder durch hohen
Kurzschlussstrom in Brand geraten. Die richtigen Vorsichtsmaßnahmen beachten. Die
Wartung muss von qualifiziertem Wartungspersonal durchgeführt werden, das im
Umgang mit Batterien geübt ist und über gute Kenntnisse der erforderlichen
Vorsichtsmaßnahmen verfügt. Nicht autorisiertes Personal von Batterien fern halten.
SDie Batterien müssen ordnungsgemäß entsorgt werden. Hierbei sind die örtlichen
Bestimmungen zu beachten.
SBatterien niemals verbrennen, da sie explodieren können.
Avvisi di sicurezza
IMPORTANTI ISTRUZIONI DI SICUREZZA
CONSERVARE QUESTE ISTRUZIONI
Il presente manuale contiene importanti istruzioni da seguire durante l’installazione e la
manutenzione dell’UPS e delle batterie. Leggere integralmente le istruzioni prima di
utilizzare l’apparecchiatura e conservare il presente manuale per futuro riferimento.

SAFETY WARNINGS
Avaya 9130 1000–3000 VA UPS Site Preparation, Installation and Operator’s Manual S164201765 Rev 1
10
PERICOLO
La TENSIONE contenuta in questo gruppo statico di continuità è LETALE. Tutte le operazioni
di riparazione e di manutenzione devono essere effettuate ESCLUSIVAMENTE DA
PERSONALE TECNICO AUTORIZZATO. All’interno del gruppo statico di continuità NON vi
sono PARTI RIPARABILI DALL’UTENTE.
AVVERTENZA
SL’UPS contiene la propria fonte di energia (batterie). Le prese d’uscita dell’UPS possono
essere sotto tensione anche quando l’UPS non è collegato all’alimentazione elettrica CA.
SPer ridurre il rischio di incendio o di scossa elettrica, installare il gruppo statico di
continuità in un ambiente interno a temperatura ed umidità controllata, privo di agenti
contaminanti conduttivi. La temperatura ambiente non deve superare i 40°C. Non
utilizzare l’unità in prossimità di acqua o in presenza di umidità eccessiva (90% max).
SPer ridurre il rischio di incendio, effettuare il collegamento soltanto a un circuito dotato
di una protezione da sovraccarico per il circuito derivato di max. 100 ampere come
stabilito dalle norme statunitensi sugli impianti elettrici (NEC, ANSI/NFPA 70).
SLa protezione da sovraccarico per le uscite e l’interruttore di scollegamento devono
essere forniti da altri produttori.
SPer conformità con gli standard internazionali e con le norme in merito al cablaggio, tutta
l’apparecchiatura collegata con l’uscita del gruppo statico di continuità non deve avere
una corrente di dispersione di terra superiore a 3,5 milliampere.
ATTENZIONE
SLe batterie possono comportare un rischio di scossa elettrica o di ustione in seguito a
un’elevata corrente di corto circuito. Osservare le dovute precauzioni. L’assistenza deve
essere eseguita da personale qualificato esperto di batterie e delle necessarie
precauzioni. Tenere il personale non autorizzato lontano dalle batterie.
SLe batterie devono essere smaltite in modo corretto. Per i requisiti di smaltimento fare
riferimento alle disposizioni locali.
SNon gettare mai le batterie nel fuoco poichè potrebbero esplodere se esposte alle
fiamme.

SAFETY WARNINGS
Avaya 9130 1000–3000 VA UPS Site Preparation, Installation and Operator’s Manual S164201765 Rev 1 11
Viktig Sikkerhetsinformasion
VIKTIGE SIKKERHETSINSTRUKSJONER
GJEM DISSE INSTRUKSJONENE
Denne håndboken inneholder viktige instruksjoner som du bør overholde ved montering og
vedlikehold av UPS-enheten og batteriene. Les alle instruksjoner før utstyret tas i bruk, og
gjem håndboken til fremtidig referanse.
FARLIG
Denne UPS’en inneholder LIVSFARLIGE SPENNINGER. All reparasjon og service må kun
utføres av AUTORISERT SERVICEPERSONALE. BRUKERE KAN IKKE UTFØRE SERVICE PÅ
NOEN AV DELENE i UPS’en.
FARLIG
SUPS-enheten inneholder sin egen energikilde (batterier). UPS-utgangen kan være
strømførende selv når UPS-enheten ikke er koblet til et strømuttak.
SFor å redusere fare for brann eller elektriske støt, bør denne UPS’en installeres i et
innendørs miljø med kontrollert temperatur og luftfuktighet som er fritt for ledende,
forurensende stoffer. Romtemperaturen må ikke overskride 40°C. Den må ikke brukes i
nærheten av vann eller ved meget høy luftfuktighet (90% maks.).
SFor å redusere brannfaren skal det bare kobles til et kretsløp med 100 A maksimum
linjeforgrenings overbelastningsbeskyttelse i henhold til NEC, ANSI/NFPA 70.
SOverbelastningsbeskyttelse for strømutgang og bryterkontakt skal leveres av andre.
SAlt utstyr som er forbundet med utgangen av denne UPS’en må ikke ha en sterkere total
lekkasjestrøm enn 3,5 milliampere for å være i overensstemmelse med internasjonale
standarder og forkablingsbestemmelser.
FORSIKTIG
SBatterier kan utgjøre en fare for elektrisk støt eller brannsår pga. høy kortsluttingsstrøm.
Treff passende forholdsregler. Service bør utføres av kvalifisert servicepersonale med
kjennskap til batterier og nødvendige forholdsregler. Hold uautorisert personale borte fra
batteriene.
SBatterier må fjernes på korrekt måte. Se lokale forskrifter vedrørende krav om fjerning av
batterier.
SKast aldri batterier i flammer, da de kan eksplodere, hvis de utsettes for åpen ild.

SAFETY WARNINGS
Avaya 9130 1000–3000 VA UPS Site Preparation, Installation and Operator’s Manual S164201765 Rev 1
12
Regulamentos de Segurança
INSTRUÇÕES DE SEGURANÇA IMPORTANTES
GUARDE ESTAS INSTRUÇÕES
Este manual contém instruções importantes que devem ser seguidas durante a instalação e
manutenção do no-break e das baterias. Leia todas as instruções antes de operar o
equipamento e guarde este manual para consultá-lo futuramente.
CUIDADO
A UPS contém VOLTAGEM MORTAL. Todos os reparos e assistência técnica devem ser
executados SOMENTE POR PESSOAL DA ASSISTÊNCIA TÉCNICA AUTORIZADO. Não há
nenhuma PEÇA QUE POSSA SER REPARADA PELO USUÁRIO dentro da UPS.
ADVERTÊNCIA
SEste no-break possui sua própria fonte de energia (baterias). A saída do no-break pode
estar energizada mesmo que este não esteja conectado a uma fonte de energia elétrica.
SPara reduzir o risco de incêndios ou choques elétricos, instale a UPS em ambiente
interno com temperatura e umidade controladas e livres de contaminadores condutíveis.
A temperatura ambiente não deve exceder 40°C. Não opere próximo a água ou em
umidade excessiva (máx: 90%).
SPara reduzir o risco de incêndio, conecte somente ao circuito fornecido com a proteção
máxima de 100 ampères contra a sobretensão do circuito derivado, de acordo com a
norma ANSI/NFPA 70 do NEC.
SAproteçãocontraasobretensãodesaídaeodisjuntordeveserfornecidaporterceiros.
SPara estar de acordo com os padrões internacionais e os regulamentos de fiação, o
equipamento total conectado à saída desta UPS não deve ter uma corrente de fuga à
terra maior que 3,5 miliampères.
PERIGO
SAs baterias podem oferecer risco de choque elétrico ou queimadura, ocasionados por
alta tensão com possibilidade de curto-circuito. Tome as precauções adequadas. A
manutenção deve ser realizada por pessoal qualificado, com conhecimento sobre
baterias e ciente das precauções exigidas. Mantenha o pessoal não autorizado afastado
das baterias.
SSiga as instruções apropriadas ao desfazer-se das baterias. Consulte os códigos do local
para maiores informações sobre os regulamentos de descarte de produtos.
SNunca jogue as baterias no fogo, porque há risco de explosão.