Avidsen 112249 User manual

YLVA 2+
eN Colour video intercom
2 wires - RFID feature
ref. 112249
x2
7”
RFID
www.avidsen.com
V2
Picture memory feature
Mémorisation des visiteurs

COLOUR VIDEO INTERCOM
TABLE OF CONTENTS
A - SAFETy iNSTruCTiONS 05
1 - INTRODUCTION 05
2 - maINTeNaNCe aND CleaNINg 05
3 - ReCyClINg 05
B - prOduCT dESCripTiON 06
1 - CONTeNTs Of The kIT 06
2 - mONITOR 06
3 - DOORplaTe 07
4 - Wall bRaCkeT 07
5 - maINs aDapTOR 07
C - iNSTALLATiON 08
1 - DOORplaTe INsTallaTION 08
2 - INsTallINg The mONITOR 09
3 - CONNeCTIONs 10
3.1 - CONNECTION BETWEEN THE MONITOR AND THE INTERCOM PANEL 11
3.2 - WITH ELECTRIC LOCK 11
3.3 - WITH AUTOMATIC ENTRYWAY CONTROL 12
3.4 - ACTIVATING THE BADGES 13
A - INITIALISATION 13
B - ADDING USER BADGES 13
C - DEACTIVATING ALL BADGES 14
D - SELECTING THE ACTION ASSOCIATED WITH THE USER BADGES 14

3eN
d - uSiNg ThE prOduCT 15
1 - IDeNTIfy aND speak TO The VIsITOR 15
2 - aCTIVaTe The INTeRCOm paNel fROm The mONITOR 15
3 - OpeNINg aN eleCTRIC lOCk aND aN aUTOmaTIC
CONTROl sysTem (OpTIONal) 15
4 - INTeRCOm feaTURe 15
5 - mONITOR seTTINgs 16
6 - UNlOCkINg UsINg a baDge 16
7 - CheCkINg phOTOs TakeN IN yOUR abseNCe 16
E - TEChNiCAL ANd LEgAL iNFOrmATiON 17
1 - TeChNICal ChaRaCTeRIsTICs 17
2 - WaRRaNTy 18
3 - help aND aDVICe 18
4 - pRODUCT ReTURNs/afTeR-sales seRVICe 18
5 - DeClaRaTION Of CONfORmITy 18

5eN
COLOUR VIDEO INTERCOM
A - SAFETy iNSTruCTiONS
1 - INTRODUCTION
This video intercom system pairs two modules: a
receiver-monitor and an easy-to-install and use
intercom panel.
Key features:
• Colour video reception: when a visitor touches
the intercom panel call button, the panel
immediately transmits the image to the screen
and a chime indicates the visitor's presence.
• Short-circuit protection
• Reverse polarity protection
• Automatic exposure correction: the video
camera automatically adjusts its exposure to
match the ambient light conditions.
• Enables control over two entrances (lock and
automatic control system, optional).
• Integrated infrared vision enables the video
camera to identify visitors without needing
additional light.
• Opening the door and a control system: by
pressing buttons on the monitor, you can
control an electric lock and a dry contact for an
automatic control system (not included).
• Opening an electric strike plate or automated
entryway (not included) when one of the two
provided user badges is shown.
IMPORTANT: You must read these instructions
carefully prior to installation. In the event of
problems, our Hotline technicians are at your
service for any information.
WARNING: any connection error may cause
damage to the device and void the warranty.
2 - MAINTENANCE AND CLEANING
Before installing the intercom, it is important to
check the following points:
• Do not install in cases of extreme humidity,
temperatures, corrosion risk or dust.
• Do not expose to direct sunlight, rain, or high
humidity.
• Do not plug the device into a multi-socket plug
adaptor or extension cord.
• Be careful not to lose the administrator badge
(red colour) or your product will be locked and
the warranty voided.
Keep it in a safe place.
• Do not install near other electronic devices such
as computers, televisions or video recorders.
• Do not install near acidic chemicals, ammonia
or sources of toxic gases.
• Do not clean with abrasive or corrosive
products. Use a damp cloth with soapy water.
• Unplug the device if it is not being used for an
extended period of time.
• Do not plug the device into national
telecommunications installations.
• The cable between the monitor and intercom
panel must not be extended. Avoid junctions
(insulating screw joints, soldered joints, etc.)
3 - RECYCLING
This logo denotes that devices which are
no longer in use must not be disposed of
as household waste.
They are likely to contain hazardous
substances which are dangerous to
both health and the environment. Return
the equipment to your local distributor or use the
recycling collection service provided by your local
council.
Pour en savoir plus :
www.quefairedemesdechets.fr

6
eN
COLOUR VIDEO INTERCOM
B - prOduCT dESCripTiON
1 - CONTENTS OF THE KIT
2 - MONITOR
1 7" LCD screen
2 Lock button: enables an electric lock to
be opened
3 MENU button: enables access to monitor
settings and photos saved during your
absence
4 Left arrow / image button: allows you to
decrease the values on the monitor menu,
view the intercom panel and end the call
1x 1
5x 5 6x 1 7x 1
2x 1
8x 4
3x 1 4x 5
1 Monitor
2 Intercom panel
3 Monitor wall bracket
4 Dowels (2 for the monitor, 3 for the intercom
panel)
5 Screws (2 for the monitor, 3 for the intercom panel)
6 Screws for the intercom panel
7 Mains adapter
8 RFID badges (red x1, grey x1, blue X2)
9
10
11
1
8
5
6
7
4
3
2

7eN
COLOUR VIDEO INTERCOM
B - prOduCT dESCripTiON
5 Right arrow / receiver button: enables
the values on the monitor's menu to be
increased, enables communication with the
visitor.
6 Entryway / video camera button: enables an
electric entryway to be opened
7 Intercom button: enables communication
with a second monitor (ref. 112252)
8 Microphone
9 Connection terminals
10 Power supply input
11 Loudspeaker
*Subject to availability.
3 - DOORPLATE
SW1
SW2
LK+
LK-
1
2
1
2
8
7
9
10
11
3
4
5
6
1 Protective hood
2 Lens
3 Microphone
4 Infrared illumination
5 Loudspeaker
6 Call button, backlit name plate according to
the ambient light
7 Dry contact connection terminal
8 Electric strike plate connection terminal
9 Monitor connection terminal
10 RFID reset button
11 RFID badge entryway/strike selector switch
4 - WALL BRACKET
The monitor is designed to be xed to the wall. A wall bracket and the necessary fasteners are included.
5 - MAINS ADAPTER
A 230 Vac 50 Hz/17 Vdc 1.5 A mains adapter for powering the monitor is included in the kit. Do not use other
power supplies as they could cause irreparable damage to the device and invalidate the warranty.
Do not cut or shorten the wire of the mains adapter or the warranty will be void.

8
eN
C - iNSTALLATiON
COLOUR VIDEO INTERCOM
The recommended installation height for the intercom panel is about 160 cm from the ground and 150 cm
from the floor for the indoor unit.
50cm
160cm 150cm
70°
WARNING: For obvious safety reasons, the connections must only be made after shutting off the power
supply.
1 - DOORPLATE INSTALLATION
The doorplate must not be directly exposed to bad weather. It should preferably be installed under a porch
or covered area.
Attach the doorplate hood to your support using the screws and wall plugs suited to the support (the screws
and plugs supplied are suitable for solid walls).
85mm
50mm
ø6 mm
After making the connections on the doorplate (see the connections paragraph), put the doorplate into the
hood.

9eN
Then screw the doorplate to the hood with the screw provided.
Put on the name label.
1LOV/DUVVRQ
2 - INSTALLING THE MONITOR
Attach the wall mount to the wall using the screws and wall plugs suited to the support (the screws and plugs
supplied are suitable for solid walls).
After connecting the monitor (refer to the "connections" paragraph), t the monitor onto its support.
59mm
ø6 mm
C - iNSTALLATiON
COLOUR VIDEO INTERCOM

10
eN
C - iNSTALLATiON
COLOUR VIDEO INTERCOM
3 - CONNECTIONS
• Do not increase the number of insulating screw joints or connectors on the connecting wire between the
doorplate and the monitor
• Keep the connecting wire between the doorplate and the monitor more than 50 cm away from any
electromagnetic interference (230 V cable, WiFi device, microwave ovens, etc.)
• You can connect and use the electric door release (not provided) with your doorplate, with or
without mechanical memory.
Between the monitor and the doorplate (100m maximum)
To ensure good audio and video quality, it is advised to not use more than 100m of cable between the
intercom and the doorplate. Connect the wires as follows (incorrect wiring can damage the doorplate).
The cable's length determines which cable section is to be used:
Cable length Section to use
0 to 50 m 0.75 mm2
50 m to 100 m 1.5 mm2
Between the doorplate and an electric latch (not included)
Use a 12V/0.5A maximum electric latch with or without mechanical memory.
For the connection between the doorplate and the door release, use a cable of this kind:
Cable length Section to use
0 to 50 m 0.75 mm2
Between the doorplate and the automated gate (not included)
Section to use: Min. 0.75 mm2

11 eN
C - iNSTALLATiON
COLOUR VIDEO INTERCOM
3.1 - CONNECTION BETWEEN THE MONITOR AND THE INTERCOM PANEL
17 VDC power
supply
(included)
Master Monitor
Not used on this model
Contacts used to connect an
additional monitor (ref. 112252,
not included)
3.2 - WITH ELECTRIC LOCK
Contacts used to connect an
additional monitor (ref. 112252,
not included)
Master Monitor
12 VDC Electric strike plate
(500 mA to 1 A), optional
17 VDC power
supply
(included)
Not used on this model
IMPORTANT: if you have trouble opening the lock, which may be caused by a large distance between the
screen and the intercom panel, for example, we recommend that you connect it to a separate power supply.
If you use a separate power supply, you must connect a 12 V relay (not included) to control it from the video
intercom, as illustrated.

12
eN
C - iNSTALLATiON
COLOUR VIDEO INTERCOM
12 VDC
Relay with 12 V coil
and NO contact
ref. 104765
230 VAC
13
14
5
9
3.3 - WITH AUTOMATIC ENTRYWAY CONTROL
IMPORTANT: connect SW1 and SW2 directly to the opening/closing contact of the automatic control system
(automated entryway wired control system input).
Contacts used to connect an
additional monitor (ref. 112252,
not included)
Not used on this model
Master Monitor
17 VDC
power supply
(included)
3.4 - ACTIVATING THE BADGES
Three types of badges are included: the red administrator badge, the grey add badge and the blue user
badges.

13 eN
d - uSiNg ThE prOduCT
COLOUR VIDEO INTERCOM
A - INITIALISATION
With the video doorkeeper powered on, press on the “RESET” button on the back of the intercom panel.
The intercom panel will beep 4 times.
Within the next 10 seconds, bring the administrator badge (red) in front of the camera.
Within the next 10 seconds, bring the add badge (grey) in front of the camera.
B - ADDING USER BADGES
Bring the add badge (grey) in front of the camera.
The intercom panel will beep 3 times.
Within the next 10 seconds, bring one of the user badges in front of the camera.

14
eN
C - iNSTALLATiON
COLOUR VIDEO INTERCOM
The intercom panel will beep 1 time.
C - DEACTIVATING ALL BADGES
Hold the administrator badge in front of the camera to deactivate all of the recognized badges. (including
the add badge).
D - SELECTING THE ACTION ASSOCIATED WITH THE USER BADGES
At the back of the intercom panel, select the electric strike plate or dry contact output to control
one or the other at the swipe of a user badge.

15 eN
d - uSiNg ThE prOduCT
1 - IDENTIFY AND SPEAK TO THE VISITOR
The visitor presses on the intercom panel's
Nils Larsson button:
1LOV/DUVVRQ
The chime sounds through the monitor's speaker
and the intercom panel's video camera is activated.
If the visitor is positioned within the camera's field of
vision, their image will appear on the monitor for 120
seconds. After 120 seconds, the monitor will return
to sleep mode.
To speak with the visitor, press the button. To
end the conversation and deactivate the intercom
panel, press the button.
2 - ACTIVATE THE INTERCOM PANEL FROM
THE MONITOR
To identify a visitor without them knowing they are
being observed or to simply look outside, press the
button: the view from the intercom panel will
then appear on the screen for 60 seconds.
If you wish to communicate directly with the outside,
press once on the button when the external
video camera is displayed.
This particularly useful feature allows you to observe
the visitor, even if they haven't pressed the intercom
panel's Nils Larsson button.
3 - OPENING AN ELECTRIC LOCK AND AN
AUTOMATIC CONTROL SYSTEM (OPTIONAL)
If the device is equipped with an electric lock and/
or an automatic control system (see "Connection"
paragraph), press the button (for the lock) or
the button (for the automatic control system) to
let a visitor enter.
4 - INTERCOM FEATURE
You can initiate internal communication with the
secondary monitor (if present) using the intercom
feature. This feature can be used when the monitor
is in sleep mode: Press the button on the
secondary monitor. You can call the secondary
monitor and vice versa. You can answer by pressing
the button and communicate for a maximum of
120 seconds. The terminal will then return to sleep
mode.
Communication with the intercom panel has priority.
COLOUR VIDEO INTERCOM

16
eN
d - uSiNg ThE prOduCT
COLOUR VIDEO INTERCOM
5 - MONITOR SETTINGS
With the screen is on, press the button to
display the following screen:
Press the button again to browse through the
sub-menus (they will light up when selected).
15
15
14
27
8
5
BRT.
CON.
COL.
CALL.
INCOME.
RING.
2016.09.13
11:01:52
DATE.
TIME.
DEL.
EXIT.
• BRT:
Brightness: press the and buttons to
decrease or increase the brightness level of the
image.
•CON:
Contrast: press the and buttons to
decrease or increase the contrast level of the image.
• COL:
Colour: press the and buttons to decrease
or increase the saturation level of the image.
• CALL:
Microphone volume: press the and
buttons to increase or decrease the microphone
volume.
• INCOME:
Chime volume: press the and buttons to
decrease or increase the ring volume.
• RING:
Choose the ring tone: press the and
buttons to select the desired tone.
15
15
14
27
8
5
BRT.
CON.
COL.
CALL.
INCOME.
RING.
2016.09.13
11:01:52
DATE.
TIME.
DEL.
EXIT.
• DATE:
Press the and buttons to adjust the
highlighted value and the button to switch to
the next value. The date and time are indicated on
the photos taken during your absence.
• TIME:
Press the and buttons to adjust the
highlighted value and the button to switch to
the next value. The date and time are indicated on
the photos taken during your absence.
• DEL:
To erase all saved photos, press the button.
• EXIT:
Press the button to close the settings menu.
6 - UNLOCKING USING A BADGE
Hold one of the user badges up in front of the
intercom panel's camera to unlock the strike plate
or the connected automated entryway.
7 - CHECKING PHOTOS TAKEN IN YOUR
ABSENCE
Each call causes a photo to be saved.
To consult the saved photos, press the button
while the screen is off.

17 eN
1 - TECHNICAL CHARACTERISTICS
MONITOR
Screen
Resolution
Transmission system (audio and video)
Video standard
Supply voltage
Power consumption
Power supply
Security
Ideal operating temperature range
Number of doorbell melodies
Max. degree of humidity
Conversation time
Dimensions
Ultra-flat 7" colour LCD
800 x 3 (RGB) x 480
2 wires
PAL/NTSC
17 VDC 1.5 A (adapter included)
from 3.5 W to 11.5 W
with 230 VAC 50 Hz / 17 VDC 1.5 A
mains adapter included
Short circuit and reverse polarity protection
-10 °C to 50 °C
9
85 %
automatically shuts off after 2 minutes
275 x 120 x 15 mm
Intercom panel
Video camera
Lens
Power supply
Max. consumption
Brightness
Dimensions
Night vision
Protection rating
CMOS 3003 colour
Fixed-focus / 70° viewing angle
CC 10-12 V supplied by the monitor
300 ± 50 mA
min. 0 lux
130 x 90 x 24.5 mm
from 0.5 to 1 m
IP54
E - TEChNiCAL ANd LEgAL iNFOrmATiON
COLOUR VIDEO INTERCOM

18
eN
E - TEChNiCAL ANd LEgAL iNFOrmATiON
COLOUR VIDEO INTERCOM
2 - WARRANTY
• This product is guaranteed for parts and labour
for 2 years from the date of purchase. Proof of
purchase must be retained for the duration of
the warranty period.
• The warranty does not cover damage caused
by negligence, knocks, or accidents.
• The parts of this product must not be opened
or repaired by any persons not employed by
Avidsen.
• The warranty will be void if the device is
tampered with.
• Do not cut or shorten the wire of the mains
adapter or the warranty will be void.
3 - HELP AND ADVICE
• If, in spite of the care we have taken in designing
our products and drafting these instructions,
you do encounter difficulties when installing
your product or you have any questions, we
urge you to contact one of our specialists who
will be glad to help.
• If you encounter operating problems during
the installation or a few days afterwards, it is
essential that you are in front of your installation
when contacting us, so that one of our
technicians can diagnose the source of the
problem, as it will probably be the result of a
setting that is incorrect or an installation that is
not to specification.
contact our after sales team on:
0,35 € / min
0 892 701 369
Monday to Friday, 9AM to 12PM and 2PM to 6PM.
4 - PRODUCT RETURNS / AFTER SALES
SERVICE
If, despite the care we have taken in designing and
manufacturing your product, it needs to be returned
to our customer service centre, you can check the
progress of the work on our website at the following
address: http://sav.avidsen.com
Avidsen undertakes to keep a stock of spare parts
for this product throughout the contractual warranty
period.
5 - DECLARATION OF CONFORMITY
Per the RED directive
Avidsen hereby declares that the equipment
designated below:
Colour video intercom 112249
Complies with the RED directive and its conformity
has been assessed pursuant to the applicable
standards in force:
EN 60950-1:2006 + A11:2009 + A1:2010 + A12:
2011 + A2 :2013
EN 301 489-1 V1.9.2
EN 301 489-3 V1.6.1
EN 300 330-1 V2.1.0
Chambray les Tours, date: 09/01/2016
Alexandre Chaverot, CEO

Avidsen France S.A.S - 32, rue Augustin Fresnel
37170 Chambray les Tours - France