Avigilon AI NVR User manual

AINVR Standard 10GbE Kit
Installation Guide
AINVR-STD-10GBE
For
AINVR-STD
1

© 2021,Avigilon Corporation. All rights reserved. AVIGILON, the AVIGILON logo, AVIGILON are trademarks
of Avigilon Corporation. Intel is a trademark of Intel Corporation or its subsidiaries in the U.S. and/or other
countries. Other names or logos mentioned herein may be the trademarks of their respective owners. The
absence of the symbols ™ and ® in proximity to each trademark in this document or at all is not a disclaimer of
ownership of the related trademark. Avigilon Corporation protects its innovations with patents issued in the
United States of America and other jurisdictions worldwide (see avigilon.com/patents). Unless stated
explicitly and in writing, no license is granted with respect to any copyright, industrial design, trademark,
patent or other intellectual property rights of Avigilon Corporation or its licensors.
This document has been compiled and published using product descriptions and specifications available at
the time of publication. The contents of this document and the specifications of the products discussed
herein are subject to change without notice. Avigilon Corporation reserves the right to make any such
changes without notice. Neither Avigilon Corporation nor any of its affiliated companies: (1) guarantees the
completeness or accuracy of the information contained in this document; or (2) is responsible for your use of,
or reliance on, the information. Avigilon Corporation shall not be responsible for any losses or damages
(including consequential damages) caused by reliance on the information presented herein.
Avigilon Corporation
avigilon.com
20211022
2

Table of Contents
Introduction 4
Confirm Package Contents 4
Required Tools 5
Installing the AINVR Standard 10GbE Kit 6
Installing the 10GbECard in Slot 2 of Expansion Riser 1 8
Installing the 10GbECard in Slot 3 of Expansion Riser 1 10
Reattach the AINVR Cover 13
Confirming the Installation 14
For More Information 16
3

Introduction
Avigilon provides an optional 10GbE Kit for the AINVR Standard. This kit provides you with a high-speed
Ethernet port for faster connections to your security network of ACC Servers and Clients.
Important: An AINVR Standard with the:
l10GbE Kit installed is supported on Release ACC7.12.4 or later.
l10GbE Kit and the Performance Upgrade Kit installed is supported on Release ACC7.14.2 or
later.
Your organization must upgrade to a release of the ACCsoftware that supports the upgraded
AINVR Standard if it is using an earlier release of the software.
Part Number Description
AINVR-STD-10GBE AINVR Standard 10GbE Kit
Note: If the AINVR is an operating part of your security system, be aware that it must be shut down
to complete this procedure.
Important: If you are installing both the AINVR Standard 10GbE Kit (AINVR-STD-10GBE) and the
AINVR Performance Upgrade Kit (AINVR-STD-PRK) in the AINVR, it is recommended that you install
the components from both kits as follows:
1. Install CPU and RAM from the AINVR Performance Kit using the instructions up to the section
“2. Removing the Original GPU Card” in the AINVR Standard Performance Kit Installation
Guide.
2. Install the second GPU card using the instructions in the section “Installing the 10GbECard in
Slot 3 of Expansion Riser 1” of the AINVR Standard 10GbE Kit Installation Guide, which
includes instructions to install the GPU card provided in AINVR Performance Upgrade Kit.
Confirm Package Contents
Confirm that the kit you are installing contains the following components:
o1 × 4-port 10GbE Direct Attach SFP+ PCIe card
o1 × low-profile PCIe bracket (required for the optional installation step of moving the BOSS card to slot 4)
Introduction 4

Required Tools
The following tools are not included in the kit package, but are needed to complete the installation:
lPhillips #2 screwdriver
Important: It is recommended that you always use an antistatic mat and antistatic strap while
working on components inside the system.
Required Tools 5

Installing the AINVR Standard 10GbE Kit
Before starting to install the kit:
1. Turn off the AINVR, including all attached peripherals. Press the power button on the front panel, and
wait for the light to stop blinking to indicate shutdown is complete.
WARNING — Opening or removing the system cover while the system is powered on may
expose you to a risk of electric shock.
2. Disconnect the AINVR from the electrical outlet and disconnect the peripherals.
3. Remove all network, power and peripheral cables from the AINVR.
4. If applicable, remove the AINVR from the rack.
Important: Whenever you need to lift the system, get others to assist you. To avoid injury, do
not attempt to lift the system by yourself.
5. At the top of the AINVR, unlock the latch release then lift and rotate the latch towards the back of the
unit. The cover slides back and is released from the body.
Tip: Use a Phillips #2 screwdriver to remove the shipping screws before unlatching the cover
if you are removing the cover of an AINVR for the first time.
Installing the AINVR Standard 10GbE Kit 6

The procedure used to install the 10 GbEcard depends on whether or not you have installed, or plan to install
the AINVRStandard Performance Upgrade Kit (AINVR-STD-PRK) in the AINVR. Refer to the following table
for the correct procedure:
If you have… Use...
No plans to install the AINVRPerformance
Upgrade Kit
Installing the 10GbECard in Slot 2 of Expansion Riser 1 on
the next page
Installed the AINVRPerformance Upgrade
Kit
Installing the 10GbECard in Slot 3 of Expansion Riser 1 on
page10
Plans to install the AINVRPerformance
Upgrade Kit
Installing the AINVR Standard 10GbE Kit 7

Installing the 10GbECard
in Slot 2 of Expansion Riser 1
Use this procedure if you have no plans to install the AINVRPerformance Upgrade Kit in the AINVR.
With the AINVR open:
1. Unpack the 10GbEcard.
2. Remove the pre-installed graphics card in slot 1 of expansion riser 1:
a. Pull the expansion card latch out of its slot.
Note: The card in this illustration does not match the appearance of the actual card
being removed from slot 1.
b. Hold the expansion card by its edges, and pull the card until the card edge connector
disengages from the expansion card connector on the riser.
c. Set aside the graphics card you removed on an ESDmat to reinstall later.
3. Install the 10GbEcard in slot 2 and then reinstall the GPUcard removed from slot 1 back in slot 1. For
each card:
a. Slide the card into the slot guide opposite the connector to align the connector on the card with
the connector on the riser.
b. Insert the card edge connector firmly into the expansion card connector until the card is fully
seated.
Installing the 10GbECard in Slot 2 of Expansion Riser 1 8

Note: This illustration shows how a card is installed in slot 1 and then how the
expansion card latch is closed. The technique to install the 10GbE card in slot 2 is the
same, except it is beneath the card in slot 1 and has to be installed first. The card in this
illustration does not match the appearance of the actual card installed in slot 1.
c. After both cards are installed, push the expansion card latch closed.
Installing the 10GbECard in Slot 2 of Expansion Riser 1 9

Installing the 10GbECard
in Slot 3 of Expansion Riser 1
Use this procedure if the AINVRPerformance Upgrade Kit is installed in the AINVR, or is planned to be
installed.
Important: For early AINVR STD models, the BOSScontroller card is installed in riser 1 slot 3 and
must be moved to the low-profile slot in riser 2 (slot 4), so that the 10GbEcard can be installed in slot
3. If you will be moving the BOSScard, you need the low-profile bracket provided in the kit to
complete this procedure. In newer models the BOSS card is preinstalled in the low-profile slot.
In this procedure, all the cards are removed from expansion riser 1 and the removed cards and the
10GbEcard are then installed as follows:
Card Location
BOSScard (with low profile bracket) if removed from slot 3 Slot 4, expansion riser 2
10GbE card Slot 3, expansion riser 1
2nd GPU (reserved for the AINVRStandard Performance Kit) Slot 2, expansion riser 1
Original GPU Slot 1, expansion riser 1
Installing the 10GbECard in Slot 3 of Expansion Riser 1 10