Avigilon AINVR-STD-PRK User manual

AINVR Standard Performance
Kit
Installation Guide
AINVR-STD-PRK
For
AINVR-STD
1

© 2022,Avigilon Corporation. All rights reserved. AVIGILON, the AVIGILON logo, AVIGILON are trademarks
of Avigilon Corporation. Intel is a trademark of Intel Corporation or its subsidiaries in the U.S. and/or other
countries. Other names or logos mentioned herein may be the trademarks of their respective owners. The
absence of the symbols ™ and ® in proximity to each trademark in this document or at all is not a disclaimer of
ownership of the related trademark.
This document has been compiled and published using product descriptions and specifications available at
the time of publication. The contents of this document and the specifications of the products discussed
herein are subject to change without notice. Avigilon Corporation reserves the right to make any such
changes without notice. Neither Avigilon Corporation nor any of its affiliated companies: (1) guarantees the
completeness or accuracy of the information contained in this document; or (2) is responsible for your use of,
or reliance on, the information. Avigilon Corporation shall not be responsible for any losses or damages
(including consequential damages) caused by reliance on the information presented herein.
Avigilon Corporation
avigilon.com
20220309
2

Table of Contents
Introduction 4
Confirm Package Contents 5
Required Tools 5
Installing the AINVR Standard Performance Kit 6
1. Opening the AINVR 7
2. Installing the CPU 9
3. Installing Additional RAM 12
4. Removing the Pre-installed GPU Card 13
5. Installing the New GPUcard 14
6. Reattach the NVR5 Cover 15
7. Confirming the Installation 16
For More Information 18
3

Introduction
Avigilon provides an optional AINVR Performance Upgrade Kit for the AINVR Standard. This kit increases
the analytic capacity of the AINVR allowing it to run more concurrent analytics. See the Analytics Sizing
Guide for more details.
Important: An AINVR Standard with the:
lPerformance Upgrade Kit installed is supported on Release ACC7.12.4 or later.
lPerformance Upgrade Kit and the 10GbE Kit installed is supported on Release ACC7.14.2 or
later.
Your organization must upgrade to a release of the ACCsoftware that supports the upgraded
AINVR Standard if it is using an earlier release of the software.
Part Number Description
AINVR-STD-PRK AINVR Standard Performance Upgrade Kit
Note: If the AINVR is an operating part of your security system, be aware that it must be shut down
to complete this procedure.
Important: If you are installing both the AINVR Standard 10GbE Kit (AINVR-STD-10GBE) and the
AINVR Performance Upgrade Kit (AINVR-STD-PRK) in the AINVR, it is recommended that you install
the components from both kits as follows:
1. Install CPU and RAM from the AINVR Performance Kit using the instructions up to the section
“2. Removing the Original GPU Card” in the AINVR Standard Performance Kit Installation
Guide.
2. Install the second GPU card using the instructions in the section “Installing the 10GbECard in
Slot 3 of Expansion Riser 1” of the AINVR Standard 10GbE Kit Installation Guide, which
includes instructions to install the GPU card provided in AINVR Performance Upgrade Kit.
Introduction 4

Confirm Package Contents
Confirm that the kit you are installing contains the following components:
o1 × Intel Xeon CPU
o1 × processor bracket
o1 × heat sink
o2 × 8GB RDIMM
o1 × P2200 GPU
Required Tools
The following tools are not included in the kit package, but are needed to complete the installation:
lPhillips #2 screwdriver
Important: It is recommended that you always use an antistatic mat and antistatic strap while
working on components inside the system.
Confirm Package Contents 5

Installing the AINVR Standard Performance Kit
Before starting to install the kit:
1. Log in to the ACC Client on a workstation on the same network as the AINVR you are going to
upgrade.
a. In the System Explorer, select the AINVR you are going to upgrade.
b. In the New Task menu, click Server Analytics . Note down the number of cameras
analytics enabled connected to the AINVR and the current resource loads. For more
information, see the Enabling Analytics topic in the ACC Client Help.
2. Turn off the AINVR, including all attached peripherals.
WARNING — Opening or removing the system cover while the system is powered on may
expose you to a risk of electric shock.
3. Disconnect the AINVR from the electrical outlet and disconnect the peripherals.
Important: It is recommended that you always use an antistatic mat and antistatic strap while
working on components inside the system.
4. If applicable, remove the system from the rack.
Important: Whenever you need to lift the system, get others to assist you. To avoid injury, do
not attempt to lift the system by yourself.
Install the kit components in the following order:
1. Opening the AINVR 7
2. Installing the CPU 9
3. Installing Additional RAM 12
4. Removing the Pre-installed GPU Card 13
5. Installing the New GPUcard 14
6. Reattach the NVR5 Cover 15
7. Confirming the Installation 16
Installing the AINVR Standard Performance Kit 6

1. Opening the AINVR
1. At the top of the AINVR, unlock the latch release then lift and rotate the latch towards the back of the
unit. The cover slides back and is released from the body.
Tip: Use a Phillips #2 screwdriver to remove the shipping screws before unlatching the cover
if you are removing the cover of an AINVR for the first time.
2. Remove the black plastic protective cover over the socket. Press the 2 blue clips and lift off the cover.
The protective cover is no longer needed and can be recycled.
3. View the interior of the AINVR and identify the locations where the components of the kit will be
installed.
The view below shows the details of an AINVR with all of the covers and cards removed, and
important components labeled with numbers.
Important: The view below does not show the GPUcard that is pre-installed in slot 1 of
Expansion Card Riser 1 Slot 1 (labeled 10 in the diagram). Do not remove this card as part of
this upgrade.
The components affected by the AINVR Standard Performance Upgrade Kit are:
l4— Memory module
The 2 DIMMs in the upgrade kit are installed here.
l5—CPU2 processor and heat sink module socket (with dust cover)
The second CPU in the performance kit is installed here.
1. Opening the AINVR 7

l10—Expansion Card Riser 1
The second P2200 GPU card is installed on the middle slot (Slot 2) of this riser, below the
original GPUcard in the top slot (slot 1).
Note: The other components pointed out in the diagram are not affected by installing the
AINVR Standard Performance Kit.
1. Opening the AINVR 8

2. Installing the CPU
You need the processor bracket, processor (CPU), and heatsink provided in the kit to complete this
procedure.
With the AINVR open and the protective cover removed:
1. Locate the 2nd processor socket and pull off the CPUdust cover with the yellow label over the socket.
2. Unpack the CPU.
3. Place the processor in the processor tray.
Note: Ensure that the pin 1 indicator on the processor tray is aligned with the pin 1 indicator on
the processor.
4. Flex the outer edges of the processor bracket and ensure that the processor is locked into the clips on
the bracket.
Note: Ensure that the pin 1 indicator on the bracket is aligned with the pin 1 indicator on the
processor before placing the bracket.
5. Unpack the heatsink. Be careful not to touch the thermal paste that is pre-applied to the bottom of the
heatsink.
6. Place the heat sink on the processor and push down on the base of the heat sink until the bracket
locks onto the heat sink.
Important: To avoid damaging the fins on the heat sink, do not press down on the heat sink
fins.
2. Installing the CPU 9

lEnsure that the 2 guide pin holes on the bracket match the guide holes on the heat sink.
lEnsure that the pin 1 indicator on the heat sink (circled red in the image below) is aligned with
the pin 1 indicator on the bracket before placing the heat sink onto the processor and bracket.
7. Align the pin 1 indicator on the heat sink to the system board and then place the processor and heat
sink module on the processor socket.
Important: Ensure that the processor and heat sink module is held parallel to the system
board to prevent damaging the components.
8. Push the blue retention clips inward to allow the heat sink to drop into place.
2. Installing the CPU 10

Important: Do not force the processor into the socket. The processor should slide easily into
the socket when aligned correctly.
9. Use the star-shaped screwdriver #T30 to tighten the screws on the heat sink in the following order:
a. Partially tighten the first screw (approximately 3 turns).
b. Tighten the second screw completely.
c. Return to the first screw and tighten it completely.
Important: Do not over-tighten or strip the screws.
If the processor and heat sink module slips off the blue retention clips when the screws are partially
tightened, follow these steps to secure the module:
a. Completely loosen both of the heat sink screws.
b. Lower the processor and heat sink module on to the blue retention clips, following the
procedure as described in step 8 above.
c. Secure the processor and heat sink module to the system board, following the instructions as
described in step 9 above.
2. Installing the CPU 11

3. Installing Additional RAM
After the CPU has been installed, insert the RAM included in the kit into memory sockets B1 and B2.
Important: Handle each memory module only by the edges to ensure that you don't touch the
middle of the memory module or the metallic contacts.
Important: To prevent damage to the memory module or memory module socket during installation,
do not bend or flex the memory module. You must insert both ends of the memory module
simultaneously.
1. In the row of empty memory sockets near to the newly installed CPU, locate sockets B1 and B2.
2. Open the white ejector clips (shown as black in the diagram) on each side of the empty memory
module sockets outward to allow the memory modules to be inserted into the sockets.
3. Align the edge connector of the memory modules with the alignment key of the sockets and press the
3. Installing Additional RAM 12

memory modules into sockets until the socket levers click into place.
Important: Do not apply pressure at the center of the memory module. Apply pressure to
both ends of the memory module evenly.
Note: If you are installing both the AINVR Performance Upgrade Kit and the AINVR Standard 10GbE
Kit (AINVR-STD-10GBE) in the AINVR, use the using the instructions in the "Installing the 10GbECard
in Slot 3 of Expansion Riser 1" section of the AINVR Standard 10GbE Kit Installation Guide, which
includes instructions to install the GPU card provided in this kit, to complete the installation of both
kits.
4. Removing the Pre-installed GPU Card
1. From the back of the AINVR, locate where the original GPUcard is installed.
2. Lift the expansion card latch to release the slots in expansion riser 1.
3. Disengage the PCIe card holder latch on the GPUcard.
4. Hold the GPU by its edges and slide out the GPU at an angle to release it from the connector on the
riser.
4. Removing the Pre-installed GPU Card 13

5. Disconnect the GPU power cable from the GPU and system board.
Note: The card in this illustration does not match the appearance of the actual card installed
in slot 1.
5. Installing the New GPUcard
1. Unpack the GPUcard and prepare it for installation.
Note: For instructions, see the documentation accompanying the card.
2. At the back of the AINVR, locate where the GPUcard needs to be installed.
3. Pull the expansion card latch.
4. Remove the filler bracket
Tip: Store the filler bracket for future use. Filler brackets must be installed in empty expansion
card slots to maintain Federal Communications Commission (FCC) certification of the system.
The brackets also keep dust and dirt out of the system and aid in proper cooling and airflow
inside the system.
5. Install the new GPUcard in slot 2 and reinstall the original GPU card in slot 1.
For each card:
a. Slide the card into the slot guide opposite the connector to align the connector on the card with
the connector on the riser.
b. Insert the card edge connector firmly into the expansion card connector until the card is fully
seated.
5. Installing the New GPUcard 14

Note: This illustration shows how a card is installed in slot 1 and then how the
expansion card latch is closed. The technique to install the card in slot 2 is the same,
except it is beneath the card in slot 1 and has to be installed first. The card in this
illustration does not match the appearance of the actual card installed in slot 1.
c. Push the expansion card latch closed and re-engage the PCIe Lock .
6. Reattach the NVR5 Cover
When all the components of the kit have been installed:
1. Ensure all expansion card latches are closed and there are filler covers for all empty slots.
2. Close and lock the NVR5 Appliance cover.
3. If the NVR5 Appliance was rack mounted and removed to install the kit, remount it into the rack.
4. Reconnect all the peripherals and cables.
5. Power on the NVR5 Appliance.
6. Reattach the NVR5 Cover 15

7. Confirming the Installation
Verify the upgrade is successful:
1. Log in to the ACC Client on a workstation on the same network as the AINVR.
2. In the System Explorer, click Site Setup, and click Site to expand the site containing the upgraded
AINVR.
3. Click to select the upgraded AINVR.
4. Verify the status of the upgraded AINVR and the presence of the two advanced processing cards:
a. Click Server Management to open the Server Management panel.
b. Enter the administrator credentials for the AINVR.
c. On the Server Management Dashboard, check that:
lThe status indicators on the ACC Server and System cards are green.
lTwo Quadro P2200 cards appear on the Accelerators card and their status is green
d. Log out of the Server Management and close the panel.
5. Verify that the AINVR has 2 CPUs and 32GBof memory installed.
a. In the System Explorer, select the upgraded AINVR server.
b. In the New Task menu , click Site Health.
c. Under the General Information heading, the sum of Memory usage and System Available
Memory should be approximately 32 GB (~32,000 MB).
d. Under the Temperature Probes heading, you should see readings for CPU1 and CPU2.
6. Verify that the analytics load capacity has increased:
a. In the System Explorer, select the upgraded AINVR.
b. In the New Task menu , click Server Analytics . For more information, see the Enabling
Analytics topic in the ACC Client Help.
c. The number of connected cameras should be the same as before the AINVR was upgraded,
and the analytics load should be about half of what it was prior to the upgrade.
7. Confirming the Installation 16

Limited Warranty
Avigilon warranty terms for this product are provided at avigilon.com/warranty.
7. Confirming the Installation 17

For More Information
For additional product documentation and software and firmware upgrades, visit support.avigilon.com.
Technical Support
Contact Avigilon Technical Support at support.avigilon.com/s/contactsupport.
lWindows™ Upgrade and Recovery Guide for Avigilon Systems (link)
lHewlett Packard Enterprise HPE iLO 5 User Guide (link)
lHewlett Packard HPE Gen10 Security Reference Guide (link)
For More Information 18