AVLink HX-1542W User manual

4*2 HDMI MATRIX
HX-1542W
USER MANUAL V1.0
HX-1542W
Package C ntents-
 1x HX-1542W Unit
 1x User Manual
 1x Power Adapter DC 12V with ock
 1x Remote Controller with Battery
 2x Screws
 4x Foot Pads
Any thing missed, please contact with your vendor.
Features
 4 HDMI inputs and 2 HDMI outputs matrix
 Support high-resolution display up to 4Kx2K@60Hz
(YCbCr 4:2:0 8/10/12/16-bit, RGB/ YCbCr444 only
8-bit)
 Supports 3D pass-through
 HDCP2.2/HDCP1.4 Compliant
 EDID Copy from OUT port 1
 Supports IR remote control
 Supports RS-232 control
-1-
Specificati ns
Functi n HX-1542W
HDMI In Connector HDMI A-Type Female x 4
HDMI Out Connector HDMI A-Type Female x 2
IR In 3.5ψ Stereo Jack x 1
RS-232 Port 9 Pin Female D Type Connector
Baud Rate 9600 bps; 8 data bits, 1 stop bit,
no parity
Max. Resolution 4K x 2K@60Hz
Power Adapter (Min.) DC 12V with ock
Housing Metal
Dimensions ( xWxH) 150 x 80 x 25 mm
Weight 296 g
FRONT VIEW
1. HDMI IN1
2. HDMI IN2
3. IR IN
4. HDMI IN3
5. HDMI IN4
REAR VIEW
1.DC JACK
2.RS-232
3.HDMI OUT2
4.HDMI OUT1
-2-
TOP VIEW
1. TACK SWITCH
2. IR2
3. ED
Installati n
1. Turn off the HDMI source and HDMI display.
2. Connect the HDMI cable between the HDMI source and
the “HDMI IN1~IN4” port of HX-1542W.
3. Turn on the HDMI source and display .
4. Select source by TACK SW, IR or RS-232
Operati n
1. Key button Of Top Unit
Press OUT1 Key: Change Output1 ink Input Port
Press OUT2 Key: Change Output2 ink Input Port
2. Remote Controller
Press Key “1” : Change Output1 ink Input Port
Press Key “2” : Change Output2 ink Input Port

-3-
(Opti nal) IR Receiver Cable
Install
Put it into the HX-1542W “IR IN” port and place the IR
Receiver Cable, so that you can point to it easily with your
IR remote controller.
RS-232 C ntr l
Connect the RS-232 cable between the PC and the
“RS-232” port of HX-1542W.
Key in the command you can change source to output
Command ist:
“route 1 1“ OUT1IN1
“route 1 2“ OUT1IN2
“route 1 3“ OUT1IN3
“route 1 4“ OUT1IN4
“route 2 1“ OUT2IN1
“route 2 2“ OUT2IN2
“route 2 3“ OUT2IN3
“route 2 4“ OUT2IN4
“Help” Display command ist
-4-
Additi nal Opti n
Select any additional options you may require.
1. IR Receiver Cable
Technical Specificati ns Output Signal
Pin # Signal Pin # Signal
1 TMDS Data 2+ 11 TMDS Clock Shield
2 TMDS Data 2 Shield 12 TMDS Clock -
3 TMDS Data 2- 13 CEC
4 TMDS Data 1+ 14 Reserved
(N.C. on device)
5 TMDS Data 1 Shield 15 SC
6 TMDS Data 1- 16 SDA
7 TMDS Data 0+ 17 DDC/CEC Ground
8 TMDS Data 0 Shield 18 +5 Power
9 TMDS Data 0- 19 Hot Plug Detect
10 TMDS Clock+
© AV INK GROUP TD., All rights reserved.
Trademarks:
All the companies, brand names, and product names
referred to this manual are the trademarks or registered
trademarks belonging to their respective companies.
-5-